ASA image upgrade

tahir_mahmood_kamboh — Wed, 23 Apr 2014 16:26:33 GMT

Need to upgrade my Cisco ASA-5510 image from asa821-k8.bin to asa903-k8.bin with the following License. Do I need to buy a new license with image upgrade ????

#sh version

Cisco Adaptive Security Appliance Software Version 8.2(1)

Device Manager Version 6.2(1)

Compiled on Tue 05-May-09 22:45 by builders

System image file is "disk0:/asa821-k8.bin"

Config file at boot was "startup-config"

TMN-5510 up 294 days 2 hours

Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz

Internal ATA Compact Flash, 256MB

BIOS Flash M50FW080 @ 0xffe00000, 1024KB

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)

Boot microcode : CN1000-MC-BOOT-2.00

SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03

IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04

0: Ext: Ethernet0/0 : address is ***************************

1: Ext: Ethernet0/1 : address is ***************************

2: Ext: Ethernet0/2 : address is ***************************

3: Ext: Ethernet0/3 : address is ***************************

4: Ext: Management0/0 : address ****************************

5: Int: Internal-Data0/0 : address is *****************************

6: Int: Internal-Control0/0 : address is ****************************

Licensed features for this platform:

Maximum Physical Interfaces : Unlimited

Maximum VLANs : 100

Inside Hosts : Unlimited

Failover : Active/Active

VPN-DES : Enabled

VPN-3DES-AES : Enabled

Security Contexts : 2

GTP/GPRS : Disabled

SSL VPN Peers : 2

Total VPN Peers : 250

Shared License : Disabled

AnyConnect for Mobile : Disabled

AnyConnect for Linksys phone : Disabled

AnyConnect Essentials : Disabled

Advanced Endpoint Assessment : Disabled

UC Phone Proxy Sessions : 2

Total UC Proxy Sessions : 2

Botnet Traffic Filter : Disabled

This platform has an ASA 5510 Security Plus license.

Serial Number: ***************************

Running Activation Key: ****************************************************************************

Configuration register is 0x1

Configuration last modified by enable_15 at 22:29:35.255 ****************** Fri Apr 4 2014

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------

Need help

>Do I need to buy a new

ROBERTO TACCON — Wed, 23 Apr 2014 18:33:00 GMT

>Do I need to buy a new license with image upgrade ????

But check the:

https://supportforums.cisco.com/document/48646/asa-83-upgrade-what-you-need-know

2) migrate the configuration from 8.21 to 9.03 asking cisco TAC help

In addition to Roberto's

Marvin Rhoads — Wed, 23 Apr 2014 22:53:06 GMT

In addition to Roberto's correct answer...

Please note that your ASA 5510 with 256 MB of RAM would need an upgrade to 1 GB to run ASA 8.3 or later software.

This is documented here.

Thanks Sir!!!!

tahir_mahmood_kamboh — Fri, 25 Apr 2014 19:25:21 GMT

Thanks Sir!!!!

Thanks for the concise and

tahir_mahmood_kamboh — Fri, 25 Apr 2014 19:26:42 GMT

Thanks for the concise and concrete answer.

topic ASA image upgrade in Network Security

ASA image upgrade

>Do I need to buy a new

In addition to Roberto's

Thanks Sir!!!!

Thanks for the concise and