ASA 5510 configuring ethernet interfaces problem

andrew278 — Mon, 11 Mar 2019 12:28:56 GMT

New ASA, was made "config factory-default"

Then I set to Ethernet 0/0 192.168.164.56/22. But when I tried to ping it "ping 192.168.164.56", I've got "No route to host 192.168.164.56". What's the problem?

------

My running-config:

ciscoasa# show running-config

: Saved

ASA Version 8.0(2)

hostname ciscoasa

enable password xxx

names

interface Ethernet0/0

no nameif

no security-level

ip address 192.168.164.56 255.255.252.0

interface Ethernet0/1

shutdown

no nameif

no security-level

no ip address

interface Ethernet0/2

shutdown

no nameif

no security-level

no ip address

interface Ethernet0/3

shutdown

no nameif

no security-level

no ip address

interface Management0/0

nameif management

security-level 100

ip address 192.168.1.1 255.255.255.0

management-only

passwd xxx

ftp mode passive

pager lines 24

logging asdm informational

mtu management 1500

no failover

icmp unreachable rate-limit 1 burst-size 1

no asdm history enable

arp timeout 14400

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00

timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00

timeout uauth 0:05:00 absolute

dynamic-access-policy-record DfltAccessPolicy

http server enable

http 192.168.1.0 255.255.255.0 management

no snmp-server location

no snmp-server contact

snmp-server enable traps snmp authentication linkup linkdown coldstart

no crypto isakmp nat-traversal

telnet timeout 5

ssh timeout 5

console timeout 0

dhcpd address 192.168.1.2-192.168.1.254 management

dhcpd enable management

threat-detection basic-threat

threat-detection statistics access-list

class-map inspection_default

match default-inspection-traffic

policy-map type inspect dns preset_dns_map

parameters

message-length maximum 512

policy-map global_policy

class inspection_default

inspect dns preset_dns_map

inspect ftp

inspect h323 h225

inspect h323 ras

inspect rsh

inspect rtsp

inspect esmtp

inspect sqlnet

inspect skinny

inspect sunrpc

inspect xdmcp

inspect sip

inspect netbios

inspect tftp

service-policy global_policy global

prompt hostname context

Cryptochecksum:xxx

: end

Re: ASA 5510 configuring ethernet interfaces problem

allanc_16 — Wed, 09 Apr 2008 12:58:25 GMT

Issue the command "show int Ethernet0/0" and see if the interface is up.

Also to make a complete configuration go ahead and assign a name to the interface and a security level.

interface Ethernet0/0

nameif myInterface

security-level 99

no shut

Thanks!

Re: ASA 5510 configuring ethernet interfaces problem

andrew278 — Thu, 10 Apr 2008 07:02:04 GMT

Thank you very much. The problem was solved by this two lines:

nameif myInterface

security-level 99

topic Re: ASA 5510 configuring ethernet interfaces problem in Network Security

ASA 5510 configuring ethernet interfaces problem

Re: ASA 5510 configuring ethernet interfaces problem

Re: ASA 5510 configuring ethernet interfaces problem