topic Re: EIGRP not working in Network Security https://community.cisco.com/t5/network-security/eigrp-not-working/m-p/1275530#M974469 <HTML><HEAD></HEAD><BODY><P>Raj</P><P></P><P>EIGRP is not supported in the SMI (Base) image. You need to upgrade the image to the EMI version. This can be done on the same switch but there will be a cost to upgrading.</P><P></P><P>Jon</P></BODY></HTML> Wed, 21 Oct 2009 15:19:41 GMT Jon Marshall 2009-10-21T15:19:41Z EIGRP not working https://community.cisco.com/t5/network-security/eigrp-not-working/m-p/1275529#M974467 <P>I have the follow Cisco switch:</P><P></P><P>WIENEU_CORE#sho ver</P><P>Cisco IOS Software, C3550 Software (C3550-IPBASE-M), Version 12.2(25)SEB4, RELEASE SOFTWARE (fc1)</P><P>Copyright (c) 1986-2005 by Cisco Systems, Inc.</P><P>Compiled Tue 30-Aug-05 13:14 by yenanh</P><P></P><P>ROM: Bootstrap program is C3550 boot loader</P><P></P><P> WIENEU_CORE uptime is 3 years, 5 weeks, 5 days, 1 hour, 34 minutes</P><P>System returned to ROM by power-on</P><P>System restarted at 16:10:29 GMT Tue Sep 12 2006</P><P>System image file is "flash:c3550-ipbase-mz.122-25.SEB4/c3550-ipbase-mz.122-25.SEB4.bin"</P><P></P><P>Cisco WS-C3550-48 (PowerPC) processor (revision S0) with 65526K/8192K bytes of memory.</P><P>Processor board ID CAT1012Z3P5</P><P>Last reset from warm-reset</P><P>Running Layer2/3 Switching Image</P><P></P><P>Ethernet-controller 1 has 12 Fast Ethernet/IEEE 802.3 interfaces</P><P></P><P>Ethernet-controller 2 has 12 Fast Ethernet/IEEE 802.3 interfaces</P><P></P><P>Ethernet-controller 3 has 12 Fast Ethernet/IEEE 802.3 interfaces</P><P></P><P>Ethernet-controller 4 has 12 Fast Ethernet/IEEE 802.3 interfaces</P><P></P><P>Ethernet-controller 5 has 1 Gigabit Ethernet/IEEE 802.3 interface</P><P></P><P>Ethernet-controller 6 has 1 Gigabit Ethernet/IEEE 802.3 interface</P><P></P><P>48 FastEthernet interfaces</P><P>2 Gigabit Ethernet interfaces</P><P></P><P>The password-recovery mechanism is enabled.</P><P>384K bytes of flash-simulated NVRAM.</P><P>Base ethernet MAC Address: 00:17:94:23:1E:00</P><P>Motherboard assembly number: 73-5701-10</P><P>Power supply part number: 34-0967-03</P><P>Motherboard serial number: CAT10120FQQ</P><P>Power supply serial number: DTH1005895S</P><P>Model revision number: S0</P><P>Motherboard revision number: A0</P><P>Model number: WS-C3550-48-SMI</P><P>System serial number: CAT1012Z3P5</P><P>Configuration register is 0x10F</P><P></P><P>I have configured routing on, but when I try to configure eigrp i get the message 'Protocol not in this image'.</P><P>Can I upgrade or does the protocol not work on this device?</P> Fri, 21 Feb 2020 11:44:56 GMT https://community.cisco.com/t5/network-security/eigrp-not-working/m-p/1275529#M974467 RVirdi 2020-02-21T11:44:56Z Re: EIGRP not working https://community.cisco.com/t5/network-security/eigrp-not-working/m-p/1275530#M974469 <HTML><HEAD></HEAD><BODY><P>Raj</P><P></P><P>EIGRP is not supported in the SMI (Base) image. You need to upgrade the image to the EMI version. This can be done on the same switch but there will be a cost to upgrading.</P><P></P><P>Jon</P></BODY></HTML> Wed, 21 Oct 2009 15:19:41 GMT https://community.cisco.com/t5/network-security/eigrp-not-working/m-p/1275530#M974469 Jon Marshall 2009-10-21T15:19:41Z Re: EIGRP not working https://community.cisco.com/t5/network-security/eigrp-not-working/m-p/1275531#M974471 <HTML><HEAD></HEAD><BODY><P>Thanks Jon.</P><P>That's exactly the answer I was hoping for.</P></BODY></HTML> Thu, 22 Oct 2009 07:09:07 GMT https://community.cisco.com/t5/network-security/eigrp-not-working/m-p/1275531#M974471 RVirdi 2009-10-22T07:09:07Z