Router Configuration

dimigav1977 — Thu, 12 Aug 2021 22:19:57 GMT

Can someone recognize what is the following and how this translated to cisco router (IOS15.7) configuration?

[sip]
sig_port=5060
rtp_port=10000
rtp_port_max=10020
sig_tos=184
voice_tos=184
qos_enable=1
session_time_enable=1
session_time=1800
session_time_min=90
dtmf_event_payload=0
crypto=1
mwi_enable=0
mwi_period=3600
digit_map=1xxxxx|[26789]xxxxxxxxx|4[0-2]xxxxxxxx|54xxx|50xxxxxxxx|00xxxxxxxxxxx.T|807xxxx|*xx*.T|*xx*x.#|*#xx#|#xx#|#xx*x.#|*xx*x.*x.#|*xx*x.T|*xx#|**xx
reg_T1=32
reg_T2=100
stun_enable=0
stun_addr=
base_time=30
o_base_time=90
max_time=1800
srtp=0
only_trusted_ca=0
prefer_crypto=AES_CM_128_HMAC_SHA1_80
reg_mode=0 (0=fallback, 1=secure, 2=insecure)
naptr_enable=0
enable_100rel=1
use_white_list=0
clip_source=0
option_enable=0
option_time=250
emergency=100|166|199|112
nat_short_num=
ims_call_feature_enable=0
internal_enable=0
codec_perport=0
ipv6_support=0
codec_perport=0
gain_perport=0
bEcPerport=0
bRtcpPerport=1
bFaxPerport=0
bJBPerport=1

[sipreg-1]
sip_reg_enable=1
sip_provider_id=1
proxy=ngn.hol.net
proxy_port=5060
sec_proxy=
sec_proxy_port=5060
reg_proxy=ngn.hol.net
reg_proxy_port=5060
user_agent=
sec_user_agent=
reg_domain=ngn.hol.net
ob_enable=0
obproxy=
obproxy_port=0
sec_obproxy=
sec_obproxy_port=5060
reg_expire=1800
reg_period=0
dnssrv_enable=1
keep_alive_enable=0
keep_alive_timeout=0
tx_port_type=1

[sip-line1]
enable=1
user=2392XXXXXX@ngn.hol.net
pw=********
telno=2392XXXXXX
display_name=Account1
cf_number=
sipreg_idx=0
single_use=0
busy_reject=0
telno_hide=0
send_reg=1
local_port=5060
txptype=1
sipprovider_id=1
sipprofile_id=1
sipline_id=1
Guiline_idx=0
sipabsoluteline_id=101
nRegisterStatus=2
nRegisterResponseCode=200
nCallStatus=0
nEmergencyCall=0
dtmf_relay=0

[FWD sip-line1]
cf_mode=0
CFU_number=
CFB_number=
CFN_number=

[Supplementary-1]
internal_no=**1
lan_internal_no=
Hotline enable=0
Hotline number=
Hotline delay=7000
CallHold enable=1
Call3Way enable=1
CallXfer enable=1

[voice]
analog_tx_gain=7
analog_rx_gain=21
hold_inact=1
bFaxDetection=1
Hook offh_persist=200
Hook br_min=20
Hook br_max=90
Hook mk_min=20
Hook mk_max=80
Hook pd_enable=0
Hook flash_min=80
Hook flash_max=900
Hook onhook_min=910

[-- Coder line-1 (only show enable line)--]
[name=PCMA]
codec=8
pack=20
vad=0
vbd_pt=255
clock=8000
channel=1
bitrate=65536
nAbsoluteLineId=101
[name=G729]
codec=18
pack=20
vad=0
vbd_pt=255
clock=8000
channel=1
bitrate=40960
nAbsoluteLineId=101
[name=telephone-event]
codec=101
pack=20
vad=0
vbd_pt=255
clock=8000
channel=1
bitrate=0
nAbsoluteLineId=101

[general]
first_dgt_tout=15000
dgt_tout=4000
record_intercal_call=0
model_name=VFH300S
firmware_version=1.0.10.07T3

spd_dial_enable=1
dpm_enable=1
ss_dpm_enable=1

[fxs-1]
enable=1
Gain dsp_tx_gain=-7
Gain dsp_rx_gain=-8
Gain fax_tx_gain=0
Gain fax_rx_gain=-6
Gain agc_on=0
EC bEnable=1
EC bInUse=0
EC u16Tail=5
RTCP Enable=1
RTCP EnableXR=0
RTCP TxInterval=5000
FAX u16Mode=2
FAX u32T38EcType=0
FAX u32T38LsRedundancy=0
FAX u32T38HsRedundancy=0
FAX u32T38BitRate=7200
FAX u32T38RateMgt=0
FAX u32T38Ecm=0
FAX u32FaxCng=0
FAX u32IdrLevel=0
FAX u32T30CdrLevel=0
FAX bXModem=1
JB u16Fixed=0
JB u32Min=40
JB u32Max=140
bSupportG722=1
out_sip_altern=0
in_sip_map=0001
out_sip_map[1]=0
out_sip_map[2]=-1
out_sip_map[3]=-1
out_sip_map[4]=-1
out_sip_map[5]=-1
out_sip_map[6]=-1
out_sip_map[7]=-1
out_sip_map[8]=-1
out_sip_map[9]=-1
out_sip_map[10]=-1
out_sip_map[11]=-1
out_sip_map[12]=-1
out_sip_map[13]=-1
out_sip_map[14]=-1
out_sip_map[15]=-1

[fxs-2]
enable=1
Gain dsp_tx_gain=-7
Gain dsp_rx_gain=-8
Gain fax_tx_gain=0
Gain fax_rx_gain=-6
Gain agc_on=0
EC bEnable=1
EC bInUse=0
EC u16Tail=5
RTCP Enable=1
RTCP EnableXR=0
RTCP TxInterval=5000
FAX u16Mode=2
FAX u32T38EcType=0
FAX u32T38LsRedundancy=0
FAX u32T38HsRedundancy=0
FAX u32T38BitRate=7200
FAX u32T38RateMgt=0
FAX u32T38Ecm=0
FAX u32FaxCng=0
FAX u32IdrLevel=0
FAX u32T30CdrLevel=0
FAX bXModem=1
JB u16Fixed=0
JB u32Min=40
JB u32Max=140
bSupportG722=1
out_sip_altern=0
in_sip_map=0000
out_sip_map[1]=-1
out_sip_map[2]=-1
out_sip_map[3]=-1
out_sip_map[4]=-1
out_sip_map[5]=-1
out_sip_map[6]=-1
out_sip_map[7]=-1
out_sip_map[8]=-1
out_sip_map[9]=-1
out_sip_map[10]=-1
out_sip_map[11]=-1
out_sip_map[12]=-1
out_sip_map[13]=-1
out_sip_map[14]=-1
out_sip_map[15]=-1

[HS]

[DECT]
dect_active=1
halb=0
eco_mode=0
pin=0000
adddect=0
rf19apu_mlse=

[SPY]
spy_enable=0
spy_level=2
tcr_level=6
strSpyFileName=/var/voice.log
strSipFileName=/var/sip.log
strLsmFileName=/var/lsm.log
strSbmFileName=/var/sbm.log
strCsmFileName=/var/csm.log
strSipCtrlFileName=/var/sipctrl.log
strSpyDir=/var/voip_log

[SPY]
spy_enable=0
loglevel=2
tcrtracelevel=6

[FCI]
target_number=
call_duration=0
call_success_time=0
max_retry_attempts=0
enable=0

[WANIF]
if_name=nas0_1
ipv4_con_state=1
ipv4_ip_addr=10.220.41.176
ipv4_gw_addr=
ipv4_dns1_addr=
ipv6_con_state=0
ipv6_ip_addr=
ipv6_gw_addr=
ipv6_dns1_addr=
===CONF END===

Re: Router Configuration

Elliot Dierksen — Fri, 13 Aug 2021 15:12:25 GMT

5060 is the default SIP signaling port, so nothing to do there. To restrict the RTP port range would be this.

voice service voip
 rtp-port range 10000 10020

That would limit you quite a lot on the number of calls. Is the an SBC/CUBE config, or are you trying to register line side? Please provide some more details on what you are trying to accomplish.

Re: Router Configuration

dimigav1977 — Fri, 13 Aug 2021 20:05:59 GMT

I think is from an ISP router trying to register to sip provider. This router provided by ISPs to home users for GPON/ONT FFTH. This is all that I have. I'm trying to understand too.

Re: Router Configuration

Elliot Dierksen — Sat, 14 Aug 2021 02:07:40 GMT

That makes it sounds like this is some kind of ATA type device trying to register as the line side of SIP. I have seen some examples of a CUBE router (or CME) allowing the line side to register, but I have never seen it register as the line side client.

Re: Router Configuration

dimigav1977 — Sat, 14 Aug 2021 08:18:40 GMT

Could you give me some information on examples of this kind? Could this connection be made with a C2901 router with uck9 licenses ??

Re: Router Configuration

Elliot Dierksen — Sat, 14 Aug 2021 13:16:11 GMT

Not from what I can find. I think the device config sounds like something that would be in an ATA with multi-platform software. Basically something that is acting like a phone.

Re: Router Configuration

dimigav1977 — Sat, 14 Aug 2021 20:42:26 GMT

The attached file is sip log from this device and 10.220.41.176 is the device IP address taken from ISP DHCP Server.

topic Re: Router Configuration in Unified Communications Infrastructure

Router Configuration

Re: Router Configuration

Re: Router Configuration

Re: Router Configuration

Re: Router Configuration

Re: Router Configuration

Re: Router Configuration