topic Re: WLC5508 in HA with OEAP in Wireless

WLC5508 in HA with OEAP

csco10734177 — Sun, 04 Jul 2021 07:15:49 GMT

Hi,

is it possible to combine the AP in local mode and the OEAP on WLC in HA mode?

1. I configured the WLC5508 in HA mode with AP in local mode registered:ok

2. When the HA in up and running, it is not possible to configure the NAT on management interface!

is it a limitation ?

in advance thank you support.

Augustin

WLC5508 in HA with OEAP

Scott Fella — Thu, 20 Jun 2013 17:15:51 GMT

WLC in HA doesn't support OEAP600 so I would think that it would also not support enabling nat ip.

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

Re: WLC5508 in HA with OEAP

Kasper Roholt — Fri, 21 Jun 2013 06:40:28 GMT

I have this serup running. You need to disable sso when configuring nat ip. After configuring nat ip you Can enable sso ( remember to enable inside så join, If used)

Sent from Cisco Technical Support iPhone App

WLC5508 in HA with OEAP

Scott Fella — Fri, 21 Jun 2013 12:43:05 GMT

Yeah, I can see that working that way, since your disabling AP SSO. I'm wondering if this is supported from TAC's point of view, because typically the feature should be available instead of having to do a work around to get something configured.

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

Re: WLC5508 in HA with OEAP

Willem de Groot — Thu, 31 Oct 2013 11:32:04 GMT

Hi,

Whats software version are you running?

is this problem solved in V7.5?

Thanks

Willem

Re: WLC5508 in HA with OEAP

Yahya Jaber — Thu, 31 Oct 2013 14:15:18 GMT

Hi Willem,

here is the official defect, subscribe to it to get any updates on it.

http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCue90285

basically, any change on the management interface will cause a reset hence a false switchover, that is why you cannot configure it.

Re: WLC5508 in HA with OEAP

Willem de Groot — Fri, 01 Nov 2013 06:16:51 GMT

Ok,

It is not possible to set the NAT as long as the HA cluster is build.
It is possible (as written above) to break the HA, set the NAt and build the HA again.

Does the OEAP600 work on the HA cluster?

Does remote LAN work as well?

Thanks

Willem

Re: WLC5508 in HA with OEAP

Kasper Roholt — Fri, 01 Nov 2013 07:04:37 GMT

Have oeap600 working in this specific setup.... Have not tested remote LAN (after HA setup)...

Kasper

Re: WLC5508 in HA with OEAP

Willem de Groot — Fri, 01 Nov 2013 08:00:45 GMT

Hi Kasper,

Thanks!

What version are you running?

Re: WLC5508 in HA with OEAP

Yahya Jaber — Fri, 01 Nov 2013 08:08:13 GMT

Hi Willem,

Yes, OEAP600 works with HA cluster in 7.5, but the client SSO does not.

Re: WLC5508 in HA with OEAP

Kasper Roholt — Fri, 01 Nov 2013 08:12:55 GMT

Hi Willem

Ver. is 7.4.100.0 (Customer have not yet find a service window to upgrade)

Kasper

Re: WLC5508 in HA with OEAP

Willem de Groot — Fri, 01 Nov 2013 08:29:33 GMT

Hi Yahya and Kasper

This is good news, My customer runs 7.4.100.60.

Client SSO is not importent on the OEAP.

Am not sure I will stay with the HA Cluster.
If I have to break the cluser, I can make it to a N+1 as well.

The main reason of the cluster was the license back in 7.3, only to have 50 Licenses for the secondary WLC.