topic Re: Cisco 2504 WLC - one AP is not joining in Wireless

Cisco 2504 WLC - one AP is not joining

ITexpert — Mon, 05 Jul 2021 15:25:13 GMT

Hello Guys,

I am using the 2504 WLC with 69 APs but 1 AP is not joining the WLC.

I dont even know where that AP physically located.

I can ping that AP from any WIFI connected device.

Please advice how to join this AP.

Thanks

@Flavio Miranda @patoberli

Thanks

Re: Cisco 2504 WLC - one AP is not joining

mohanraj_blr — Thu, 22 Mar 2018 18:29:09 GMT

Hi ,

As per your statement ap got ip, just enable capwap debug on controller to check discovery request and response going out from the wlc. how is your network is designed meaning ap got wlc ip using dhcp option 43 or directly prime into the ap?.

Re: Cisco 2504 WLC - one AP is not joining

ITexpert — Thu, 22 Mar 2018 18:30:08 GMT

After entering the command ---- sh AP join stats detailed mac-address

I got this reason : Number of message transmission to the AP has reached maximum.

Re: Cisco 2504 WLC - one AP is not joining

ITexpert — Thu, 22 Mar 2018 18:36:10 GMT

Hello Mohan,

all APs and controller management port is in default vlan and NO DHCP option 43 is configured.

i have 69 APs just this one is not joined.

when i enter command ---- sh ap join stats detailed mac

Reason fo last AP connection Failure ..... Number of message retransmission to the AP has reached max

Re: Cisco 2504 WLC - one AP is not joining

Daniel Ordóñez Flores — Thu, 22 Mar 2018 18:53:39 GMT

Hi @ITexpert @mohanraj_blr

This AP is same model that rest go them?

Re: Cisco 2504 WLC - one AP is not joining

ITexpert — Thu, 22 Mar 2018 19:01:32 GMT

I believe so but not sure because that AP is not listed In Access points in GUI.

I dont even know how to check this info from CLI.

please advice with command ?

@Daniel Ordóñez Flores

Thanks

Re: Cisco 2504 WLC - one AP is not joining

Daniel Ordóñez Flores — Thu, 22 Mar 2018 19:11:00 GMT

🙂

You said that you can ping this AP, right? can you track it the MAC address and use "show cdp neighbors" to check the model on the switch?

In your WLC can you share the output "show license capacity"

Re: Cisco 2504 WLC - one AP is not joining

ITexpert — Thu, 22 Mar 2018 19:32:52 GMT

The results of Show License Capacity

Max count: 70 Current count:68 remaining count:2 remaining capacity:7/75

Total APs are 69 , show license capacity only showing 68 that are joined.

We just acquire this building, and everything is unmanaged and no documentation, So give me some time to figure out the switch where this AP is connected.

Thanks

Re: Cisco 2504 WLC - one AP is not joining

wrainwater — Thu, 22 Mar 2018 20:03:10 GMT

I would log into the core switch and do an arp or rarp on the AP and track down the switch its connected to from there.

Do you have any type of monitoring tools such as solarwinds, whatsupgold, etc that keeps track of all the ip addresses that flow through your environment? do you have cisco prime?

As far as where it is physically, I'd use a fluke or some other RF tracking program and walk the building until you see the signal for the AP get closer. That should give you an idea of where it may be. The "Netscout Aircheck G2" looks like a great tool to use for this as well.

Re: Cisco 2504 WLC - one AP is not joining

Leo Laohoo — Fri, 23 Mar 2018 06:24:49 GMT

@wrainwater wrote:

As far as where it is physically, I'd use a fluke or some other RF tracking program and walk the building until you see the signal for the AP get closer. That should give you an idea of where it may be. The "Netscout Aircheck G2" looks like a great tool to use for this as well.

One can use the existing APs and "reverse" triangulation.

Another method is to find out if the switch the AP is connected to supports TDR and then do a TDR test to determine how far is the cable run.

Re: Cisco 2504 WLC - one AP is not joining

ITexpert — Fri, 23 Mar 2018 12:23:24 GMT

Hello Leo,

Can you explain more About Triangulation and TDR.

@Leo Laohoo

Thanks

Re: Cisco 2504 WLC - one AP is not joining

Leo Laohoo — Fri, 23 Mar 2018 12:29:02 GMT

First is to find where the AP is. Maybe it's connected to the wrong VLAN? Maybe it's crashed and the port needs to be rebooted?

Re: Cisco 2504 WLC - one AP is not joining

mohanraj_blr — Fri, 23 Mar 2018 13:38:28 GMT

Hi,

As per your below output remaining ap capacity should be 2/70, can you remove any one of the associated ap and check not joining ap connected and also check with not joined ap mac or ip with msg log and snmp trap logs, check in snmp trap or msg log for license related msg is flooding.

The results of Show License Capacity

Max count: 70 Current count:68 remaining count:2 remaining capacity:7/75

Total APs are 69 , show license capacity only showing 68 that are joined.

Re: Cisco 2504 WLC - one AP is not joining

ITexpert — Fri, 23 Mar 2018 14:43:09 GMT

Hello Guys,

Its working now, The think it was due to IP conflict-ion , Now i see that DHCP provide diff IP and its working.

@mohanraj_blr But its still showing count 6\75... Total APS 69 now... Max count-70

Thanks