https://community.cisco.com/t5/wireless/debug-eap-results/m-p/173989#M11535 <P>After setting my debug settings to troubleshoot EAP authentication, I receive the below debugger results. I am running a WinXP / Aironet 1200 / Windows 2003 IAS / Dell TrueMobile 1150 configuration, and all I want to do is get EAP to start working. Neither the Aironet debugger, the WindowsXP debugger (netsh ras set tracing eapol enabled), nor the Windows 2003 IAS logs do me any good. I'm at a loss with no information...can somebody interpret the following? It appears that some fundamental failure is occuring and kills the client communication.</P><P></P><P>MNTEFG01#debug dot11 aaa dot1x all</P><P>MNTEFG01#</P><P>01:12:27: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 0002.2d7b.0c24 Associ</P><P>ated KEY_MGMT[NONE]</P><P>*Mar 1 01:12:27.655: dot11_dot1x_parse_client_pak: Received EAPOL packet from 0</P><P>002.2d7b.0c24, type 0</P><P>*Mar 1 01:12:27.656: EAPOL pak dump rx</P><P>*Mar 1 01:12:27.656: EAPOL Version: 0x1 type: 0x1 length: 0x0000</P><P>00E11C90: 01010000 ....</P> Sun, 04 Jul 2021 15:52:28 GMT jamieforrest 2021-07-04T15:52:28Z https://community.cisco.com/t5/wireless/debug-eap-results/m-p/173989#M11535 <P>After setting my debug settings to troubleshoot EAP authentication, I receive the below debugger results. I am running a WinXP / Aironet 1200 / Windows 2003 IAS / Dell TrueMobile 1150 configuration, and all I want to do is get EAP to start working. Neither the Aironet debugger, the WindowsXP debugger (netsh ras set tracing eapol enabled), nor the Windows 2003 IAS logs do me any good. I'm at a loss with no information...can somebody interpret the following? It appears that some fundamental failure is occuring and kills the client communication.</P><P></P><P>MNTEFG01#debug dot11 aaa dot1x all</P><P>MNTEFG01#</P><P>01:12:27: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 0002.2d7b.0c24 Associ</P><P>ated KEY_MGMT[NONE]</P><P>*Mar 1 01:12:27.655: dot11_dot1x_parse_client_pak: Received EAPOL packet from 0</P><P>002.2d7b.0c24, type 0</P><P>*Mar 1 01:12:27.656: EAPOL pak dump rx</P><P>*Mar 1 01:12:27.656: EAPOL Version: 0x1 type: 0x1 length: 0x0000</P><P>00E11C90: 01010000 ....</P> Sun, 04 Jul 2021 15:52:28 GMT https://community.cisco.com/t5/wireless/debug-eap-results/m-p/173989#M11535 jamieforrest 2021-07-04T15:52:28Z https://community.cisco.com/t5/wireless/debug-eap-results/m-p/173990#M11536 <HTML><HEAD></HEAD><BODY><P>It looks like holdoff timer issue on the Access Point or client. You can change holdoff time for clients using the dot11 holdoff-time command: This timer controls how long a client has to wait before it can authenticate after using a bad password. Make the timer value as zero. Refer this document for more details:</P><P><A class="jive-link-custom" href="http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo1200/accsspts/b12211ja/b12211cr/cr11main.htm#17406" target="_blank">http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo1200/accsspts/b12211ja/b12211cr/cr11main.htm#17406</A></P></BODY></HTML> Fri, 25 Jul 2003 19:24:31 GMT https://community.cisco.com/t5/wireless/debug-eap-results/m-p/173990#M11536 sbilgi 2003-07-25T19:24:31Z