topic Not able to access controller using management interface in Wireless

Not able to access controller using management interface

wajahatkhan — Sun, 04 Jul 2021 06:50:52 GMT

Dear All,

I configure IP address on the management interface port 1 of 5508 controller when i connect it direct to my laptop i can't ping or access controller from my laptop even i connect through layer 2 switch still i can't not.

IP Address of management interface : 10.21.0.50

Laptop IP Address : 10.21.0,51

Re: Not able to access controller using management interface

Scott Fella — Fri, 05 Apr 2013 01:23:59 GMT

You need to make sure that the manager interface is untagged. The vlan should be set to zero (0). Then you will be able to ping and access the WLC.

Sent from Cisco Technical Support iPhone App

Re: Not able to access controller using management interface

Scott Fella — Fri, 05 Apr 2013 01:25:42 GMT

Now best practice is to not connect you laptop to the WLC. You know that though... So eventually you will connect it to a switch and them you will want to actually tag the vlan. So if the WLC managing is on vlan 50 let's say, you will change the manager interface vlan to 50. Hope this helps:)

Sent from Cisco Technical Support iPhone App

Not able to access controller using management interface

wajahatkhan — Fri, 05 Apr 2013 01:26:45 GMT

Thank for your reply...

Management interface is untagged and i can access using serive port but not through management interface

Re: Not able to access controller using management interface

Scott Fella — Fri, 05 Apr 2013 01:30:15 GMT

If your WLC is connected to a switch, you must make sure it's a gigabit switch. The WLC is only gigabit not 10/100/1000.

If you connect it to a switch, make sure it's a dot1q trunk port. Now connect your port on an access port assigned to that same vlan as the WLC manager interface is on.

Sent from Cisco Technical Support iPhone App

Re: Not able to access controller using management interface

Scott Fella — Fri, 05 Apr 2013 01:30:53 GMT

Please post from the CLI show interface summary

Sent from Cisco Technical Support iPhone App

Not able to access controller using management interface

wajahatkhan — Fri, 05 Apr 2013 01:31:19 GMT

i tried this as well i connect my WLC to the through switch and i tag WLC interface to vlan 10 and also configured my switch interface which is connected to wlc to configured as vlan 10 and also my laptop in vlan 10 still not working

Re: Not able to access controller using management interface

Scott Fella — Fri, 05 Apr 2013 01:33:45 GMT

The port the WLC connects to should be a trunk port not an access port.

Please post the switchport configuration the WLC is connected to and the one your laptop is connected to. Don't forget the show interface summary from the WLC.

Sent from Cisco Technical Support iPhone App

Not able to access controller using management interface

wajahatkhan — Fri, 05 Apr 2013 01:38:35 GMT

Interface Name Port Vlan Id IP Address Type Ap Mgr Guest

-------------------------------- ---- -------- --------------- ------- ------ -----

management 1 10 10.21.0.50 Static Yes No

service-port N/A N/A 192.168.102.11 Static No No

virtual N/A N/A 192.168.167.11 Static No No

PC on the switch:

interface GigabitEthernet1/0/23

switchport access vlan 10

switchport mode access

WLC on the swich

interface GigabitEthernet1/0/24

description *** connected to WLC ***

switchport trunk native vlan 10

switchport mode trunk

switch model is 2960S

Re: Not able to access controller using management interface

Scott Fella — Fri, 05 Apr 2013 01:40:24 GMT

Change your switch config to this

interface GigabitEthernet1/0/24
description *** connected to WLC ***
switchport mode trunk

Sent from Cisco Technical Support iPhone App

Re: Not able to access controller using management interface

Scott Fella — Fri, 05 Apr 2013 01:41:31 GMT

Basically this is what you need to issue

config t
interface GigabitEthernet1/24
no switchport trunk native vlan 10

Sent from Cisco Technical Support iPhone App

Re: Not able to access controller using management interface

Scott Fella — Fri, 05 Apr 2013 01:43:01 GMT

When you define the native vlan 10, you essentially are not tagging the vlan 10. So if you keep the native vlan 10 command, you need to change the manager interface vlan on the WLC to zero (0).

Sent from Cisco Technical Support iPhone App

Not able to access controller using management interface

wajahatkhan — Fri, 05 Apr 2013 01:53:55 GMT

Now i reach my home let me try in the morning and i will update you

Re: Not able to access controller using management interface

Scott Fella — Fri, 05 Apr 2013 01:58:12 GMT

No problem. Keep me posted.

Sent from Cisco Technical Support iPhone App