topic AP not joining VWLC in Wireless

AP not joining VWLC

craig.huggins — Mon, 05 Jul 2021 13:23:28 GMT

I am trying to setup a VWLC on my work network for testing, the controller is setup i am just trying to add the ap's which are 1852i-e-k9. The controller is recognizing them but they are just stuck on downloading. I have consoled onto the AP and below is the output. Does anyone have any ideas why it isn't connecting, sorry guys im new to wireless;

CAPWAP State: DTLS Teardown
[*01/18/2017 11:54:53.5111] Dropping dtls packet since session is not established. c0a89617, 147e, c0a896aa, 1480, (nil)
[*01/18/2017 11:54:58.2496] CAPWAP State: Discovery
[*01/18/2017 11:55:08.0000] CAPWAP State: DTLS Setup
[*01/18/2017 11:55:08.0799] CAPWAP State: Join
[*01/18/2017 11:55:08.0999] CAPWAP State: Image Data
[*01/18/2017 11:55:08.1299] do PRECHECK, part1 is active part

paste the output of these

Sandeep Choudhary — Wed, 18 Jan 2017 12:16:34 GMT

paste the output of these commands:

From WLC: sh sysinfo

From AP: sh version

Also paste the complete boot-up process from AP console.

Regards

Dont forget to rate helpful posts

From WLC: sh sysinfo

craig.huggins — Wed, 18 Jan 2017 12:26:19 GMT

From WLC: sh sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller
Product Version.................................. 8.0.140.0
RTOS Version..................................... 8.0.140.0
Bootloader Version............................... 8.3.15.96
Emergency Image Version.......................... 8.0.140.0

Build Type....................................... DATA + WPS

System Name...................................... CiscoWLC
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1631
IP Address....................................... 192.168.150.23
IPv6 Address..................................... ::
System Up Time................................... 1 days 2 hrs 52 mins 0 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180

Configured Country............................... GB - United Kingdom

--More-- or (q)uit

State of 802.11b Network......................... Disabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0

Burned-in MAC Address............................ 00:0C:29:EA:54:80
Maximum number of APs supported.................. 200
System Nas-Id....................................
WLC MIC Certificate Types........................ SHA1

From AP: sh version

ROM: Bootstrap program is U-Boot boot loader
BOOTLDR: U-Boot boot loader Version 24

AP00B0.E1A8.4A70 uptime is 0 days, 0 hours, 46 minutes
Last reload time : Mon Jun 20 12:20:59 UTC 2016
Last reload reason : unknown

cisco AIR-AP1852I-E-K9 ARMv7 Processor rev 0 (v7l) with 966404/740796K bytes of memory.
Processor board ID KWC203906K9
AP Running Image : 8.2.111.0
Primary Boot Image : 8.2.111.0
Backup Boot Image : 0.0.0.0
2 Gigabit Ethernet interfaces
2 802.11 Radios
Radio FW version : 21e6bdcdd6b8c8a2e3830b2f6ddab9b5
NSS FW version : NSS.AK.1.0.c10-00017-E_custC-1

Base ethernet MAC Address : 00:B0:E1:A8:4A:70
Part Number : 0-0000-00
PCA Assembly Number : 074-13149-02
PCA Revision Number : 01
PCB Serial Number : KWC203906K9
Top Assembly Part Number : 000-00000-00
Top Assembly Serial Number : KWC203906K9
Top Revision Number : A0
Product/Model Number : AIR-AP1852I-E-K9

AP Boot up process;

Requesting system reboot70]
[01/18/2017 12:23:49.5167] Restarting system.
[01/18/2017 12:23:49.5467] Going down for restart now

U-Boot 2012.07 (btldr release 24) (Apr 06 2016 - 10:42:24)

This product contains some software licensed under the
"GNU General Public License, version 2" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html

DRAM: 1 GiB
NAND (ONFI): Detected SPANSION S34MS02G2 [256 MiB]
SF: Detected Macronix MX25U3235F [4 MiB]
MFG data loaded
Scanning shenv data blocks
Total valid parts=4
Active shenv part[1:0], write_counter=3
PCI0 Link Intialized
PCI1 Link Intialized
Net:
PHY ID = 0x4dd074, eth0 found AR8033 PHY
PHY ID = 0x4dd074, eth1 found AR8033 PHY
Valid I2C chip addresses: 51 52
AP 1832/1852 detected...
Power Type: 802.3af POE or Others detected...
Signature returns 0
BL signing verification success, continue to run...
Auto boot mode, use bootipq directly
Hit ESC key to stop autoboot: 0
Specified BOOT: part1

Booting from part1

Read 1024 bytes from volume part1 to 45000000
Read 19317163 bytes from volume part1 to 45000000
Signature returns 0
Image signing verification success, continue to run...
Using machid 0x1260 from environment

Starting image ...

[01/01/1970 00:00:00.0000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d
[01/01/1970 00:00:00.0000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[01/01/1970 00:00:00.0000] Machine: Cisco Systems 11ac Wave2 Wifi Access Point
[01/01/1970 00:00:00.0000] Memory policy: ECC disabled, Data cache writealloc
[01/01/1970 00:00:00.0000] Kernel command line: ubi.mtd=0 crashkernel=30M@1280M console=ttyHSL1,9600n8 activepart=part1 activeboot=0 wdgtriggered=0
[01/01/1970 00:00:00.1500] CPU1: Booted secondary processor
[01/01/1970 00:00:10.8068] msm_serial_hs: probe of msm_serial_hs.0 failed with error -2
[01/01/1970 00:00:11.4666] buginf tty flushing thread started, ttyport=ef4c2690
[01/01/1970 00:00:15.9252] msm_hsusb_host msm_hsusb_host: unable to find transceiver
[01/01/1970 00:00:16.0551] watchdog: only one watchdog can use /dev/watchdog
[01/01/1970 00:00:16.1251] watchdog: error registering /dev/watchdog (err=-16)
[*01/01/1970 00:00:16.2950] buginf() enabled.

Welcome to Cisco.

Usage of this device is governed by Cisco's End User License Agreement,
available at:
http://www.cisco.com/c/en/us/td/docs/general/warranty/English/EU1KEN_.html.

Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to
restrictions as set forth in subparagraph (c) of the Commercial
Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

This product contains some software licensed under the
"GNU Library General Public License, version 2" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Library
General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.0.html

This product contains some software licensed under the
"GNU Lesser General Public License, version 2.1" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Lesser
General Public License, version 2.1", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html

This product contains some software licensed under the
"GNU General Public License, version 3" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, Version 3", available here:
http://www.gnu.org/licenses/gpl.html.

[*01/01/1970 00:00:16.3050] Made it into bootsh: Jun 20 2016 12:20:37
[*01/01/1970 00:00:16.3050] bootsh build T-b8710c3994a0cfe8a83c99849ab890ba4b053118-gb8710c39-kalairam
init started: BusyBox v1.20.2 (2016-06-20 11:49:35 PDT)

User Access Verification
Username: [*01/01/1970 00:00:19.5540] Active version: 8.2.111.0
[*01/01/1970 00:00:19.5540] Backup version: 0.0.0.0
[*01/01/1970 00:00:19.6840] AP1852I
[*01/01/1970 00:00:19.7740] nss_driver - Turbo Support 1
[*01/01/1970 00:00:19.7740] Supported Frequencies - 110Mhz 550Mhz 733Mhz
[*01/01/1970 00:00:19.8839]
[*01/01/1970 00:00:19.8839] phy_value=0: org="0x1000" phy_reg="0x1800"
[*01/01/1970 00:00:20.2338] Current value of FACTORY_RESET=0
[*01/01/1970 00:00:20.2438] Last reload time: Jan 18 12:23:46 2017
[*01/18/2017 12:23:46.0000] Setting system time Wed Jan 18 12:23:46 UTC 2017
[*01/18/2017 12:23:46.0399] device wired0 entered promiscuous mode
[*01/18/2017 12:23:46.1099] device wired1 entered promiscuous mode
[*01/18/2017 12:23:46.4399] stile_lm_ft_corsica: module license [01/18/2017 12:23:46.4599] stile module dp init successfully
[01/18/2017 12:23:46.5498] NBAR Label:BLD_MCP_DEV_LATEST_20150424_123021 NBAR VERSION:module build date: Nov 4 2015 at 14:26:22
'Copyright (c) 2014-2015 by cisco Systems, Inc.' taints kernel.
[*01/18/2017 12:23:46.4599] stile_lm_dp_corsica: module license 'Copyright (c) 2014-2015 by cisco Systems, Inc.' taints kernel.
[*01/18/2017 12:23:47.0797]
[*01/18/2017 12:23:47.0797] boot 2 build T-b8710c3994a0cfe8a83c99849ab890ba4b053118-gb8710c39-kalairam board corsica mac 00:B0:E1:A8:4A:70
[*01/18/2017 12:23:47.0897] Module: qca_nss_gmac .text=0xbf000000 data=0xbf006b24 bss=0xbf006fe4
[*01/18/2017 12:23:47.0897] Module: qca_nss_drv .text=0xbf010000 data=0xbf0277b0 bss=0xbf028560
[*01/18/2017 12:23:47.0897] Module: qca_nss_capwapmgr .text=0xbf044000 data=0xbf047b84 bss=0xbf047cd8
[*01/18/2017 12:23:47.0897] Module: nssmgrctl .text=0xbf04d000 data=0xbf04e728 bss=0xbf04ea4c
[*01/18/2017 12:23:47.0897] Module: proclikefs .text=0xbf054000 data= bss=0xbf054b40
[*01/18/2017 12:23:47.0897] Module: stile_lm_ft .text= data= bss=
[*01/18/2017 12:23:47.0897] Module: stile_lm_dp .text= data= bss=
[*01/18/2017 12:23:47.0897] Module: qca_nss_profile_drv .text=0xbf8b9000 data=0xbf8ba324 bss=0xbf8ba498
[*01/18/2017 12:23:47.4495] Last reload reason : reload command
[*01/18/2017 12:23:48.6692] adf: module license 'Proprietary' taints kernel.
[*01/18/2017 12:23:48.6692] asf: module license 'Proprietary' taints kernel.
[*01/18/2017 12:23:48.6792] ath_hal: module license 'Proprietary' taints kernel.
[*01/18/2017 12:23:48.6892] ath_dfs: module license 'Proprietary' taints kernel.
[*01/18/2017 12:23:48.6892] ath_rate_atheros: module license 'Proprietary' taints kernel.
[*01/18/2017 12:23:48.6992] ath_dev: module license 'Proprietary' taints kernel.
[*01/18/2017 12:23:48.7291]
[*01/18/2017 12:23:48.7291] __ol_ath_attach() Allocated scn c42c0480
[*01/18/2017 12:23:48.7391] Chip id: 0x9, chip version: 0x1000000
[*01/18/2017 12:23:48.7391]
[*01/18/2017 12:23:48.7391] Target Version is 1000000
[*01/18/2017 12:23:48.7391]
[*01/18/2017 12:23:48.7391] Flash Download Address c0000
[*01/18/2017 12:23:48.7391] ol_transfer_bin_file: flash data file defined
[*01/18/2017 12:23:48.7391] Cal location [0]: 00000000
[*01/18/2017 12:23:48.7391]
[*01/18/2017 12:23:48.7391] Wifi0 NAND FLASH Select OFFSET 0x1000
[*01/18/2017 12:23:48.7591] qc98xx_verify_checksum: flash checksum passed: 0x30f4
[*01/18/2017 12:23:48.7591] ol_transfer_bin_file 4017: Download Flash data len 12064
[*01/18/2017 12:23:48.7791]
[*01/18/2017 12:23:48.7791] Board data initialized
[*01/18/2017 12:23:48.8291] ol_ath_download_firmware :First OTP download and Execute is good address:0xa000 return param 4660
[*01/18/2017 12:23:48.8291] ol_ath_download_firmware:##Board Id 8 , CHIP Id 1
[*01/18/2017 12:23:48.8291] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=AR900B/hw.2/boardData_AR900B_CUS260_negative_pwr_offset_2G_v2_008.bin
[*01/18/2017 12:23:48.8991]
[*01/18/2017 12:23:48.8991] [Flash] : Ignore Module param
[*01/18/2017 12:23:48.9091] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0
[*01/18/2017 12:23:48.9291] ol_transfer_bin_file: Downloading firmware file: AR900B/hw.2/athwlan.bin
[*01/18/2017 12:23:50.0287] Startup Mode-0 set
[*01/18/2017 12:23:50.0287] HTC Service:0x0300 ep:1 TX flow control disabled
[*01/18/2017 12:23:50.0287] HTC Service:0x0100 ep:2 TX flow control disabled
[*01/18/2017 12:23:50.0387] Firmware_Build_Number:84
[*01/18/2017 12:23:50.0387] host/RAM_fw Build Ver Mismatch: H:0x47, F:0x54 !
[*01/18/2017 12:23:50.0387] num_rf_chain:0x00000004 ht_cap_info:0x0000185b vht_cap_info:0x339a79b2 vht_supp_mcs:0x0000ffea
[*01/18/2017 12:23:50.0387]
[*01/18/2017 12:23:50.0387] RES CFG Support wmi_service_bitmap 9778
[*01/18/2017 12:23:50.0387]
[*01/18/2017 12:23:50.0387] Sending Ext resource cfg: HOST PLATFORM as 0 and fw_feature_bitmap as 10 to TGT
[*01/18/2017 12:23:50.0387] Mesh Supported
[*01/18/2017 12:23:50.1187] wmi_ready_event_rx: WMI UNIFIED READY event
[*01/18/2017 12:23:50.1187] ACS not enabled
[*01/18/2017 12:23:50.1187] ol_ath_thermal_mitigation_attach: --
[*01/18/2017 12:23:50.1187]
[*01/18/2017 12:23:50.1187] __ol_ath_attach() Allocated scn ee4c0480
[*01/18/2017 12:23:50.1287] Chip id: 0x9, chip version: 0x1000000
[*01/18/2017 12:23:50.1287]
[*01/18/2017 12:23:50.1287] Target Version is 1000000
[*01/18/2017 12:23:50.1287]
[*01/18/2017 12:23:50.1287] Flash Download Address c0000
[*01/18/2017 12:23:50.1287] ol_transfer_bin_file: flash data file defined
[*01/18/2017 12:23:50.1287] Cal location [1]: 00004000
[*01/18/2017 12:23:50.1287]
[*01/18/2017 12:23:50.1287] wifi1 NAND FLASH Select OFFSET 0x5000
[*01/18/2017 12:23:50.1487] qc98xx_verify_checksum: flash checksum passed: 0x 2e9
[*01/18/2017 12:23:50.1487] ol_transfer_bin_file 4017: Download Flash data len 12064
[*01/18/2017 12:23:50.1687]
[*01/18/2017 12:23:50.1687] Board data initialized
[*01/18/2017 12:23:50.2187] ol_ath_download_firmware :First OTP download and Execute is good address:0x9c00 return param 4660
[*01/18/2017 12:23:50.2187] ol_ath_download_firmware:##Board Id 7 , CHIP Id 1
[*01/18/2017 12:23:50.2187] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=AR900B/hw.2/boardData_AR900B_CUS239_negative_pwr_offset_5G_v2_007.bin
[*01/18/2017 12:23:50.2887]
[*01/18/2017 12:23:50.2887] [Flash] : Ignore Module param
[*01/18/2017 12:23:50.2987] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0
[*01/18/2017 12:23:50.3186] ol_transfer_bin_file: Downloading firmware file: AR900B/hw.2/athwlan.bin
[*01/18/2017 12:23:51.0384] FWLOG: [24737] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 )
[*01/18/2017 12:23:51.0384] FWLOG: [24737] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 )
[*01/18/2017 12:23:51.0384] FWLOG: [24737] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 )
[*01/18/2017 12:23:51.0384] FWLOG: [24737] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 )
[*01/18/2017 12:23:51.4283] Startup Mode-0 set
[*01/18/2017 12:23:51.4283] HTC Service:0x0300 ep:1 TX flow control disabled
[*01/18/2017 12:23:51.4283] HTC Service:0x0100 ep:2 TX flow control disabled
[*01/18/2017 12:23:51.4283] Firmware_Build_Number:84
[*01/18/2017 12:23:51.4283] host/RAM_fw Build Ver Mismatch: H:0x47, F:0x54 !
[*01/18/2017 12:23:51.4283] num_rf_chain:0x00000004 ht_cap_info:0x0000185b vht_cap_info:0x339b79b2 vht_supp_mcs:0x0000ffea
[*01/18/2017 12:23:51.4283]
[*01/18/2017 12:23:51.4283] RES CFG Support wmi_service_bitmap 9778
[*01/18/2017 12:23:51.4283]
[*01/18/2017 12:23:51.4283] Sending Ext resource cfg: HOST PLATFORM as 0 and fw_feature_bitmap as 10 to TGT
[*01/18/2017 12:23:51.4283] Mesh Supported
[*01/18/2017 12:23:51.4983] wmi_ready_event_rx: WMI UNIFIED READY event
[*01/18/2017 12:23:51.5083] acfg_attach: Offload using existing sock eea0d200
[*01/18/2017 12:23:51.5083] ACS not enabled
[*01/18/2017 12:23:51.5083] ol_ath_thermal_mitigation_attach: --
[*01/18/2017 12:23:51.5183] ath_pktlog: module license 'unspecified' taints kernel.
[*01/18/2017 12:23:51.5183] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16
[*01/18/2017 12:23:51.5183] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16
[*01/18/2017 12:23:52.4280] FWLOG: [26108] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 )
[*01/18/2017 12:23:52.4280] FWLOG: [26108] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 )
[*01/18/2017 12:23:52.4280] FWLOG: [26108] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 )
[*01/18/2017 12:23:52.4280] FWLOG: [26108] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 )
[*01/18/2017 12:23:53.0278] click-config/io-real.click:73: While configuring 'todev_nsscapwap0 :: ToDevice':
[*01/18/2017 12:23:53.0278] warning: device 'nsscapwap0' is down
[*01/18/2017 12:23:53.0478] click-config/io-real.click:73: While configuring 'fromdev_nsscapwap0 :: FromDevice':
[*01/18/2017 12:23:53.0478] warning: device 'nsscapwap0' is down
[*01/18/2017 12:23:53.6376] pid 1401's current affinity mask: 3
[*01/18/2017 12:23:53.6376] pid 1401's new affinity mask: 1
[*01/18/2017 12:23:54.1574] wmi_dbg_cfg_send: mod[0]00000000 dbgcfg40000000 cfgvalid[0] 00000000 cfgvalid[1] 00000000
[*01/18/2017 12:23:54.1574] wmi_dbg_cfg_send: mod[0]00000000 dbgcfg40000000 cfgvalid[0] 00000000 cfgvalid[1] 00000000
[*01/18/2017 12:23:55.5270] wired0: 1000 Mbps Full Duplex
[*01/18/2017 12:23:55.5270]
[*01/18/2017 12:23:59.3858] ethernet_port wired0, ip 192.168.150.170, netmask 255.255.255.0, gw 192.168.150.254, mtu 1500, bcast 192.168.150.255, dns1 192.168.150.4, vid 0, static_ip_failover false, dhcp_vlan_failover false
[*01/18/2017 12:24:09.7826] Loading sha2...
[*01/18/2017 12:24:09.7826] Dumpping sha1...
[*01/18/2017 12:24:10.8822] Loading MIC cert and key
[*01/18/2017 12:24:10.8822] Dumpping sha2...
[*01/18/2017 12:24:11.8619] Loading MIC cert and key
[*01/18/2017 12:24:11.8619] /etc/init.d/S80cisco: line 161: /usr/bin/show_skun.lua: not found
[*01/18/2017 12:24:11.8919] Generating key, this may take a while...
[*01/18/2017 12:24:13.2015] Public key portion is:
[*01/18/2017 12:24:13.2015] ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQCAyJtXAoMwMEBhfRc36B2hY0V5oFqkzl367bDq/F3RMhPTrdW+98SBi/R6rVf2BZBoGX+NYbXP/U2h5SWXhfzuKGDl+mjeotS5yXEcAAGQ5zPMO5umN4p9Sp/cqd7SL/cKCLbwEc2ZpFCDqZSa3O4Nd/ARbOMUbtwiABgvxnR/Tpp3ZKqzOoM9K0KE8V64q24X8t8zQZDIv+rhNDxNbbHvqq7D7wvkjI6ib16w2AZF/cWHmWmQ97KUEnUzoUNLfAlnIjSGDumNPo7aY6vVQDAGqg+00ciJyFiKUBdpDojO6PAJSw0kZaX7SXPkJIUjNZUJHrHvbJLbt9S8PEshK5cz root@m00B0E1A84A70
[*01/18/2017 12:24:13.2015] Fingerprint: md5 10:9c:21:c1:e7:fa:42:53:1b:91:c3:6b:e2:68:0f:d7
[*01/18/2017 12:24:13.2515] pid 2660's current affinity mask: 3
[*01/18/2017 12:24:13.2515] pid 2660's new affinity mask: 1
[*01/18/2017 12:24:13.3315] gzip -dc /etc/wcp.usermodule.template.gz | sed -e 's/__TX_POWER_2G_FILE__/\/radio_fw\/R2.csv/g' -e 's/__TX_POWER_5G_FILE__/\/radio_fw\/R5.csv/g' -e 's/__EVM_POWER_2G_FILE__/\/radio_fw\/EVM_2.csv/g' -e 's/__EVM_POWER_5G_FILE__/\/radio_fw\/EVM_5.csv/g' -e 's/__DOMAIN_2G__/1/g' -e 's/__DOMAIN_5G__/12/g' -e 's/__PRODUCT_ID__/AIR-AP1852I-E-K9/g' -e 's/__AP_TYPE__/48/g' -e 's/__WIRELESS_MAC__/00:B0:E1:A9:8F:00/g' -e 's/__WIRED_MAC__/00:B0:E1:A8:4A:70/g' -e 's/__WIRED1_MAC__/00:B0:E1:A8:4A:70/g' | DMALLOC_OPTIONS=debug=0x4e48503,inter=1000,log=/tmp/wcp.dmalloc.log,limit=40000000 wcpd &
[*01/18/2017 12:24:13.6813] Password for 'Cisco' changed
[*01/18/2017 12:24:14.8910] DOT11_DRV[0]: Init Radio0
[*01/18/2017 12:24:14.9010] DOT11_DRV[0]: Stop Radio0
[*01/18/2017 12:24:14.9010] DOT11_DRV[0]: set_channel Channel set to 6
[*01/18/2017 12:24:14.9010] DOT11_DRV[1]: Init Radio1
[*01/18/2017 12:24:14.9110] DOT11_DRV[1]: Stop Radio1
[*01/18/2017 12:24:14.9210] DOT11_DRV[1]: set_channel Channel set to 36
[*01/18/2017 12:24:15.7207] DOT11_DRV[0]: set_channel Channel set to 1
[*01/18/2017 12:24:15.7207] DOT11_DRV[0]: Channel set to 1, width 20
[*01/18/2017 12:24:15.7307] DOT11_DRV[0]: Channel set to 1, width 20
[*01/18/2017 12:24:15.7407] DOT11_DRV[1]: set_channel Channel set to 36
[*01/18/2017 12:24:15.7507] DOT11_DRV[1]: Channel set to 36, width 20
[*01/18/2017 12:24:15.7507] DOT11_DRV[1]: Channel set to 36, width 20
[*01/18/2017 12:24:15.7607] WTP IP Address = 192.168.150.170
[*01/18/2017 12:24:15.7907] DOT11_DRV[0]: Channel set to 1, width 20
[*01/18/2017 12:24:15.7907] DOT11_DRV[0]: Channel set to 1, width 20
[*01/18/2017 12:24:15.8007] DOT11_DRV[1]: Channel set to 36, width 20
[*01/18/2017 12:24:15.8007] DOT11_DRV[1]: Channel set to 36, width 20
[*01/18/2017 12:24:15.8007] CAPWAP State: Discovery
[*01/18/2017 12:24:15.8107] CAPWAP State: Init
[*01/18/2017 12:24:15.8107] CAPWAP State: Discovery
[*01/18/2017 12:24:16.8903] device capwap0 entered promiscuous mode
[*01/18/2017 12:24:16.9203] device capwap1 entered promiscuous mode
[*01/18/2017 12:24:25.3077] CAPWAP State: Discovery
[*01/18/2017 12:25:22.0000] CAPWAP State: DTLS Setup
[*01/18/2017 12:25:22.0799] CAPWAP State: Join
[*01/18/2017 12:25:22.0999] CAPWAP State: Image Data
[*01/18/2017 12:25:22.1399] do PRECHECK, part1 is active part

Hi,

Sandeep Choudhary — Wed, 18 Jan 2017 14:12:37 GMT

Hi,

AIR-AP1852I-E-K9: This AP need minimum SW version "8.1.111.0 or higher" on WLC.

and you are running "Product Version.................................. 8.0.140.0"

Update the WLC and try again.

Here is the compatibility matrix: http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html

Regards

Dont forget to rate helpful posts

Re: AP not joining VWLC

deepakshukla27062013 — Sat, 13 Oct 2018 09:33:09 GMT

I have problem in VWLC not able to find DHCP in Image file 8.2

@craig.huggins wrote:

I am trying to setup a VWLC on my work network for testing, the controller is setup i am just trying to add the ap's which are 1852i-e-k9. The controller is recognizing them but they are just stuck on downloading. I have consoled onto the AP and below is the output. Does anyone have any ideas why it isn't connecting, sorry guys im new to wireless;

CAPWAP State: DTLS Teardown
[*01/18/2017 11:54:53.5111] Dropping dtls packet since session is not established. c0a89617, 147e, c0a896aa, 1480, (nil)
[*01/18/2017 11:54:58.2496] CAPWAP State: Discovery
[*01/18/2017 11:55:08.0000] CAPWAP State: DTLS Setup
[*01/18/2017 11:55:08.0799] CAPWAP State: Join
[*01/18/2017 11:55:08.0999] CAPWAP State: Image Data
[*01/18/2017 11:55:08.1299] do PRECHECK, part1 is active part

Re: Hi,

deepakshukla27062013 — Sat, 13 Oct 2018 09:36:35 GMT

What should be recommend Image File for 1852I for enabling the DHCP Services in VWLC.

@Sandeep Choudhary wrote:

Hi,

AIR-AP1852I-E-K9: This AP need minimum SW version "8.1.111.0 or higher" on WLC.

and you are running "Product Version.................................. 8.0.140.0"

Update the WLC and try again.

Here is the compatibility matrix: http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html

Regards

Dont forget to rate helpful posts