topic I think AP1700 can boot by in Wireless

How to convert an AP 1700 / 2700 from lightweight mode to autonomous mode ?

Atsushi Ikeda — Mon, 05 Jul 2021 08:48:23 GMT

I know that AP1700/2700 support the unified mode from version 15.3.3.

http://www.cisco.com/c/en/us/td/docs/wireless/access_point/15-3-3/configuration/guide/cg15-3-3/cg15-3-3-chap1-overview.html

But I could not change the mode because of the following error.

AP1c6a.7a92.5468#capwap ap autonomous

Convert to Autonomous image. Proceed? (yes/[no]): yes

No Autonomous image found! Conversion failed.

Why was that error message displayed ? Please tell me how I can resolve this.

Thanks.

Atsushi

You have to have the

Charlie Moreton — Mon, 27 Oct 2014 12:01:24 GMT

You have to have the autonomous IOS file downloaded to the AP.

ap3g2-k9w7-tar.153-3.JAB.tar

is the file you need, you also need valid CCO Credentials to download the file.

Please Rate Helpful posts and mark this question as answered if, in fact, this does answer your question. Otherwise, feel free to post follow-up questions.

Charles Moreton

Hello, atsushiikeda.Do you

adawa — Mon, 27 Oct 2014 14:46:11 GMT

Hello, atsushiikeda.

Do you have an existing support contract/SmartNet for these APs?

Let me know if you have additional concerns or e-mail (adawa@cisco.com) me directly. Kind regards.

Hello, Charles Thank you for

Atsushi Ikeda — Tue, 28 Oct 2014 06:29:50 GMT

Hello, Charles

Thank you for comment.

O.K. I understand the file is needed.

Is the following command right to download the file to the AP ?
"(Cisco Controller) >config ap tftp-downgrade ~~~"

Please teach me one more point.

Is it possible to convert an AP from autonomous mode to lightweight mode by using any command ? If not , is it only re-installation that allow that conversion ?

Thank you for your support.

The easiest way is to use one

Scott Fella — Tue, 28 Oct 2014 08:08:49 GMT

The easiest way is to use one of the following:

Using a TFTP Server to Return to a Previous Release

http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918

https://supportforums.cisco.com/docs/DOC-18268

http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918

http://www.youtube.com/watch?v=QQ_NuxdRhQ4

https://supportforums.cisco.com/docs/DOC-14960

HelloI tried to confirm

Atsushi Ikeda — Wed, 29 Oct 2014 02:17:37 GMT

Hello

I tried to confirm unified mode operation on an AP2700i.

I found the following results through the validation.

#Conversion from Lightweight to Autonomous

1. When we use the command( "config ap tftp-download...") for conversion on the WLC version 8.0.100, the AP can't boot as autonomous mode unless the version is earlier than 15.3(3)JAB.
*This is explicitly stated in the release note.

#Conversion from Autonomous to Lightweight

1. 15.3(3)JAB autonomous image does not run a WLC discovery process. I think this is not an assumed behaviour. So once the ap boots up as autonomous mode, it never boot up as lightweight mode n spite of the presence or absence of a WLC.

2. So when we convert the AP to autonomous mode , we may have to use lightweight image as before.

3. There is no AP1700 lightweight image 1700 on the software download site ..!

Though I don't still try, I think AP1700 can boot by using a lightweight image that is on the software download page for AP2700/3700. Is this correct ?

Thanks.

Atsushi

I think AP1700 can boot by

Rasika Nayanajith — Wed, 29 Oct 2014 03:12:49 GMT

I think AP1700 can boot by using a lightweight image that is on the software download page for AP2700/3700. Is this correct ?

Yes, it is correct, as per this 1700/2700/2600/3600/3700 all have same image starting with "ap3g2-xxx

http://www.cisco.com/c/en/us/td/docs/wireless/access_point/ios/release/notes/rn-15-3-3.html#32237

Ap3g2

1700I, 2700I/2700E,2600I/2600E, 3600I/3600E, 3700I/3700E

HTH

Rasika

**** Pls rate all useful responses ***

Hello Manannalage Thank you

Atsushi Ikeda — Wed, 29 Oct 2014 05:02:51 GMT

Hello Manannalage

Thank you so much for your answer !

I can resolve the confusioin caused by unified mode.

Atsushi

Hi AtsushiNot a problem, Glad

Rasika Nayanajith — Wed, 29 Oct 2014 05:54:37 GMT

Hi Atsushi

Not a problem, Glad if that helps you

Here is another good post you should read. It is about how to decode those image filename information.

https://supportforums.cisco.com/document/77131/understanding-access-point-ios-images

HTH

Rasika

**** Pls rate all useful responses ****

Re: The easiest way is to use one

fabianwickman — Tue, 09 Oct 2018 14:26:56 GMT

Thank you Scott.

I managed to download the image to the AP by following this:
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
(archive download sw /overwrite)

However, when I reload the AP, it still joins the WLC again like a lightweight AP.

Thanks!

Re: How to convert an AP 1700 / 2700 from lightweight mode to autonomous mode ?

m.rana.ku — Sun, 31 Jan 2021 12:09:29 GMT

Hi,
Step by Step Process has been demonstrated How to of Convert Cisco Aironet 3600 Series Access Point from Lightweight to Autonomous version.

https://www.youtube.com/channel/UCmZZ2BNGXQH1HPS3uIVnr7A?sub_confirmation=1

https://youtu.be/O2qNFVZ-KRQ

Requirements:
1.TFTPd64 Server
2.Cisco IOS Software AP3G2-K9W7-M for (C3600 Series AP)
3.The Cisco AP and the Laptop with TFTP server must be in same network.

According to my network setup
Lightweight AP BVI1 IP address is 192.168.1.4
Laptop's IP address where TFTP server is installed 192.168.1.7 [Default Router IP]

First disconnect the ethernet cable from the AP then Press the Mode button and Put back the ethernet cable to the AP and hold the Mode button Untill flash light turns to umber and Once the Lightweight AP goes to online then apply the following commands to convert it to Autonomous version:

set IP_ADDR 192.168.1.4 [According to my network setup]
set NETMASK 255.255.255.0 [According to my network setup]
set DEFAULT_ROUTER 192.168.1.7 [According to my network setup]
tftp_init
ether_init
flash_init
tar -xtract tftp://192.168.1.7/ap3g2-k9w7-tar.153-3.JH.tar flash:
dir flash
set boot flash:/ap3g2-k9w7-mx.153-3.JH/ap3g2-k9w7-mx.153-3.JH
set
boot