topic Lightweight AP disable console logging in Wireless

Lightweight AP disable console logging

Philip91 — Sun, 04 Jul 2021 07:48:08 GMT

Hello Guys,

how can i disable logging, when i am connected to an LWAP via console ?

I guess on a switch its something like "no logging console".

Is there a Lightweight AP CLI command reference ?

Thanks for help !

Greetings

Re: Lightweight AP disable console logging

Rasika Nayanajith — Tue, 10 Sep 2013 10:32:17 GMT

Try "debug capwap console cli" command & then apply "no logging console" command as shown below

APbc16.6516.790e#debug capwap console cli

This command is meant only for debugging/troubleshooting

Any configuration change may result in different

behavior from centralized configuration.

CAPWAP console CLI allow/disallow debugging is on

APbc16.6516.790e#conf t

Enter configuration commands, one per line. End with CNTL/Z.

APbc16.6516.790e(config)#no logging console

HTH

Rasika

Lightweight AP disable console logging

Rasika Nayanajith — Tue, 10 Sep 2013 10:48:39 GMT

Here are the WLC CLI command references (for 5508,2504, WiSM)

http://www.cisco.com/en/US/customer/products/ps10315/prod_command_reference_list.html

Here is the IOS XE CLI command reference (for 5700/3850)

http://www.cisco.com/en/US/customer/docs/wireless/controller/3.2_0_se/multibook/command_reference/b_consolidated_command_reference_chapter_01100.html

HTH

Rasika

Rasika you are my Hero. After

zjohnson1 — Sat, 12 Mar 2016 23:40:17 GMT

Rasika you are my Hero. After hours of searching it was your Post that saved me! THANK YOU!

Great to see this help you

Rasika Nayanajith — Sat, 12 Mar 2016 23:47:31 GMT

Great to see this help you out 😉

Rasika

Re: Lightweight AP disable console logging

Kunal Kumar Singh — Wed, 08 Aug 2018 17:57:01 GMT

The command is not working on 3802i .. what the new command to get into config t mode and also delete nvram.

Re: Lightweight AP disable console logging

davidpoole1 — Thu, 09 May 2019 11:01:18 GMT

I can get onto the 3802i but I don't see all of the cli commands

how do I view those

Re: Lightweight AP disable console logging

Sathiyanarayanan Ravindran — Thu, 09 May 2019 11:21:55 GMT

Login in to AP and go to enable mode use the command

login as: test
test@xx.xx.xx.xx's password: Enter login password
LABAP>en
Password: Enter enable password
LABAP#logging console disable

Re: Lightweight AP disable console logging

ahervey — Fri, 14 Jun 2019 14:31:59 GMT

logging console disable

Re: Lightweight AP disable console logging

Kunal Kumar Singh — Sat, 03 Aug 2019 19:58:47 GMT

Command is no more supported on 3802i as these controller can also be configured as mobility Express. Workaround is to load mobility express image on these AP and configure Mobility controller. once done. Same AP will also join as AP under mobility controller. ( Concept is similar as Autonomous WDS where an AP act as both WDS Server and AP that participate). Once AP join . You can configure AP for standalone for wireless site survey purpose.

Re: Lightweight AP disable console logging

Alejandro Josue Barquero Bustos — Tue, 28 May 2024 22:35:28 GMT

Helping 13 years after!

Re: Lightweight AP disable console logging

tidjes — Sat, 16 Aug 2025 04:05:50 GMT

Thank you very much Sir!