Getting command prompt on AP 3502i

mahesh18 — Sun, 04 Jul 2021 05:25:03 GMT

Hi all,

I have AP which is not connected to switch.

I console it and it gives error unable to to get IP from WLC.

Need to know is there any way that i can go to command prompt of this AP without getting IP from WLC??

I tried control + c etc it does not go to command prompt.

Getting command prompt on AP 3502i

Saravanan Lakshmanan — Tue, 17 Jul 2012 17:38:20 GMT

if you're not allowed to enter any info on console it could be the putty/secure crt config issue, fix that.

can't telnet/ssh to AP when it is not joined to wlc, however you should be able to console it.

Getting command prompt on AP 3502i

mahesh18 — Tue, 17 Jul 2012 18:20:23 GMT

Hi,

Thanks for reply.

How can i fix putty/secure crt config issue, fix that when i am not getting command prompt on AP?

Thanks

MAhesh

Getting command prompt on AP 3502i

Saravanan Lakshmanan — Tue, 17 Jul 2012 18:23:04 GMT

could you post the AP output and where it stops from boot process.

Getting command prompt on AP 3502i

mahesh18 — Tue, 17 Jul 2012 19:05:27 GMT

Hi,

here is boot process

r WRDTR,CLKTR: 0x88000800 0x00000000
r RQDC ,RFDC : 0x80000035 0x00000257

using eeprom values

WRDTR,CLKTR: 0x88000800 0x00000000
RQDC ,RFDC : 0x80000035 0x00000257

ddr init done

Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
......................................................................................................................................................................................................................................................
Xmodem file system is available.

DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x88000800, 0x00000000
RQDC, RFDC : 0x80000035, 0x00000257

PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
64bit PCIE devices
PCIEx: initialization done
flashfs[0]: 33 files, 8 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31739904
flashfs[0]: Bytes used: 8309760
flashfs[0]: Bytes available: 23430144
flashfs[0]: flashfs fsck took 10 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 70:81:05:c0:56:c1
Waiting for PHY auto negotiation to complete... TIMEOUT !
Ethernet link is down.

The system has encountered an error initializing
the Ethernet port.
The system is ignoring the error and continuing to boot.
If you abort the system boot process, the following
commands will re-initialize Ethernet, TFTP, and finish
loading the operating system software:

    ether_init
    tftp_init
    boot

Loading "flash:/ap3g1-k9w8-mx.124-23c.JA3/ap3g1-k9w8-mx.124-23c.JA3"...#######################################################################################################################################################################################################################################################################################################################################################################################################################################################################

File "flash:/ap3g1-k9w8-mx.124-23c.JA3/ap3g1-k9w8-mx.124-23c.JA3" uncompressed and installed, entry point: 0x4000
executing...
enet halted

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706

Cisco IOS Software, C3500 Software (AP3G1-K9W8-M), Version 12.4(23c)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 18-Oct-11 14:59 by prod_rel_team

Proceeding with system init

Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
......................................................................................................................................................................................................................................................

flashfs[1]: 33 files, 8 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31481856
flashfs[1]: Bytes used: 8309760
flashfs[1]: Bytes available: 23172096
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 1 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.

Waiting for PHY auto negotiation to complete... TIMEOUT !
Ethernet link is down.
Error: RGMII speed

Radio0 present 8364B 8000 B8020000 0 B8030000 10
Radio1 present 8364B 8000 B0020000 0 B0030000 C
status of voice_diag_test from WLC is false
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-CAP3502I-A-K9 (PowerPC460exr) processor (revision A0) with 81910K/49152K bytes of memory.
Processor board ID FGL1543S0NY
PowerPC460exr CPU at 666Mhz, revision number 0x18A8
Last reset from power-on
LWAPP image version 7.0.220.0
1 Gigabit Ethernet interface
2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 70:81:05:C0:56:C1
Part Number                          : 73-12175-05
PCA Assembly Number                  : 800-32268-05
PCA Revision Number                  : A0
PCB Serial Number                    : FOC15323GV0
Top Assembly Part Number             : 800-32891-01
Top Assembly Serial Number           : FGL1543S0NY
Top Revision Number                  : A0
Product/Model Number                 : AIR-CAP3502I-A-K9
% Please define a domain-name first.

Press RETURN to get started!

%LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
%LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
%LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
%SSH-5-ENABLED: SSH 2.0 has been enabled
%LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
%LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
%LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
%CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
%LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:09.698: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:09.707: *** CRASH_LOG = YES

*Mar 1 00:00:09.707: 64bit PCIE devicesSecurity Core found.
Base Ethernet MAC address: 70:81:05:C0:56:C1

*Mar 1 00:00:51.407: %SYS-2-INTSCHED: 'suspend' at level 0 -Process= "Init", ipl= 0, pid= 3 -Traceback= 0x5F7C0 0x1A5650 0x173DF0 0x4F3D08 0x4E8BDC 0x4A97E0 0x190ED0 0x190F84 0x56EF0 0x571D0 0x1A5AF0
*Mar 1 00:00:51.416: %SYS-2-INTSCHED: 'may_suspend' at level 0 -Process= "Init", ipl= 0, pid= 3 -Traceback= 0x5F7C0 0x1A5650 0x17415C 0x2BD1C8 0x2C272C 0x287120 0x4E86B8 0x4E8BF4 0x4A97E0 0x190ED0 0x190F84 0x56EF0 0x571D0 0x1A5AF0
*Mar 1 00:00:51.416: %SYS-2-INTSCHED: 'may_suspend' at level 0 -Process= "Init", ipl= 0, pid= 3 -Traceback= 0x5F7C0 0x1A5650 0x17415C 0x2BCEFC 0x2BD1F0 0x2C272C 0x287120 0x4E86B8 0x4E8BF4 0x4A97E0 0x190ED0 0x190F84 0x56EF0 0x571D0 0x1A5AF0
*Mar 1 00:00:51.416: %SYS-2-INTSCHED: 'may_suspend' at level 0 -Process= "Init", ipl= 0, pid= 3 -Traceback= 0x5F7C0 0x1A5650 0x17415C 0x2BCEFC 0x2BD1F0 0x2C272C 0x287120 0x4E86B8 0x4E8BF4 0x4A97E0 0x190ED0 0x190F84 0x56EF0 0x571D0 0x1A5AF0
*Mar 1 00:00:51.416: %SYS-2-INTSCHED: 'may_suspend' at level 0 -Process= "Init", ipl= 0, pid= 3 -Traceback= 0x5F7C0 0x1A5650 0x17415C 0x2BCEFC 0x2BD1F0 0x2C272C 0x287120 0x4E86B8 0x4E8BF4 0x4A97E0 0x190ED0 0x190F84 0x56EF0 0x571D0 0x1A5AF0
*Mar 1 00:00:51.416: %SYS-2-INTSCHED: 'may_suspend' at level 0 -Process= "Init", ipl= 0, pid= 3 -Traceback= 0x5F7C0 0x1A5650 0x17415C 0x2BCEFC 0x2BD1F0 0x2C272C 0x287120 0x4E86B8 0x4E8BF4 0x4A97E0 0x190ED0 0x190F84 0x56EF0 0x571D0 0x1A5AF0
*Mar 1 00:00:51.416: %SYS-2-INTSCHED: 'may_suspend' at level 0 -Process= "Init", ipl= 0, pid= 3 -Traceback= 0x5F7C0 0x1A5650 0x17415C 0x2BD1C8 0x2C272C 0x287120 0x4E86B8 0x4E8BF4 0x4A97E0 0x190ED0 0x190F84 0x56EF0 0x571D0 0x1A5AF0
*Mar 1 00:00:51.416: %SYS-2-INTSCHED: 'may_suspend' at level 0 -Process= "Init", ipl= 0, pid= 3 -Traceback= 0x5F7C0 0x1A5650 0x17415C 0x2BCEFC 0x2BD1F0 0x2C272C 0x287120 0x4E86B8 0x4E8BF4 0x4A97E0 0x190ED0 0x190F84 0x56EF0 0x571D0 0x1A5AF0
*Mar 1 00:00:51.416: %SYS-2-INTSCHED: 'may_suspend' at level 0 -Process= "Init", ipl= 0, pid= 3 -Traceback= 0x5F7C0 0x1A5650 0x17415C 0x2BCEFC 0x2BD1F0 0x2C272C 0x287120 0x4E86B8 0x4E8BF4 0x4A97E0 0x190ED0 0x190F84 0x56EF0 0x571D0 0x1A5AF0
*Mar 1 00:32:58.456: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:32:59.456: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:33:15.833: status of voice_diag_test from WLC is false
*Mar 1 00:33:15.912: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to down
*Mar 1 00:33:15.921: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:33:15.937: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up

*Mar 1 00:33:45.909: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!

*Mar 1 00:33:55.910: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!

*Mar 1 00:34:05.910: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!

*Mar 1 00:34:15.910: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does *Mar 1 00:33:45.909: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:33:55.910: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:34:05.910: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:34:15.910: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does

Getting command prompt on AP 3502i

Saravanan Lakshmanan — Tue, 17 Jul 2012 19:17:32 GMT

Waiting for PHY auto negotiation to complete... TIMEOUT !

Ethernet link is down.

did the ethernt link came up lately.

Getting command prompt on AP 3502i

mahesh18 — Tue, 17 Jul 2012 19:20:07 GMT

Hi,

I tried to connect ethernet port to pc initally.

Thanks

Getting command prompt on AP 3502i

Saravanan Lakshmanan — Tue, 17 Jul 2012 19:57:31 GMT

if my memory servers well the AP prompt may not show up until user hits enter. check the config particularly the flow control should be set to none.

Re: Getting command prompt on AP 3502i

Leo Laohoo — Tue, 17 Jul 2012 22:20:52 GMT

*Mar  1 00:00:51.416: %SYS-2-INTSCHED: 'may_suspend' at level 0 -Process= "Init", ipl= 0, pid= 3 -Traceback= 0x5F7C0 0x1A5650 0x17415C 0x2BD1C8 0x2C272C 0x287120 0x4E86B8 0x4E8BF4 0x4A97E0 0x190ED0 0x190F84 0x56EF0 0x571D0 0x1A5AF0

I'm also concerned about this error message.

topic Getting command prompt on AP 3502i in Wireless

Getting command prompt on AP 3502i

Getting command prompt on AP 3502i

Getting command prompt on AP 3502i

Getting command prompt on AP 3502i

Getting command prompt on AP 3502i

Getting command prompt on AP 3502i

Getting command prompt on AP 3502i

Getting command prompt on AP 3502i

Re: Getting command prompt on AP 3502i