topic Reset AP to factory default enable password not reset in Wireless

Reset AP to factory default enable password not reset

keith.k.quaye — Sun, 04 Jul 2021 04:24:12 GMT

I was trying to do a password recovery on a 1142 AP but enable password did not reset and I am stuck

AP model is AIR-AP1142N-A-K9

Running IOS c1140-k9w7-mx.124-21a.JA1

Its autonomous so there is no controller. Any direction would be appreciated I renamed the config.txt file but that did not help I am unable to rename or delete the private-config file. I get the message that file or directory cannot be found when i try to rename and permission denied when I try to delete it.

Re: Reset AP to factory default enable password not reset

Scott Fella — Wed, 18 Jan 2012 17:53:05 GMT

Have you tried to hold the mode button down for 15 seconds while powering up the ap?

Sent from Cisco Technical Support iPhone App

Reset AP to factory default enable password not reset

keith.k.quaye — Wed, 18 Jan 2012 18:14:32 GMT

Thanks for your response Scott but I did that with no luck I just formatted the flash (overkill I think)and I am tftping a new image to see if that helps

Re: Reset AP to factory default enable password not reset

Scott Fella — Wed, 18 Jan 2012 18:23:36 GMT

That will do it too, just didn't want to get you in that situation of having an ap with no image:)

Thanks,

Scott Fella

Sent from my iPhone

Reset AP to factory default enable password not reset

keith.k.quaye — Wed, 18 Jan 2012 18:28:16 GMT

Funny that didn't seem to work its not recognizing the default enable which i understand to be cisco. I am consoled in if that makes any difference.

Re: Reset AP to factory default enable password not reset

Scott Fella — Wed, 18 Jan 2012 18:32:37 GMT

Do an erase /all nvram:

Thanks,

Scott Fella

Sent from my iPhone

Reset AP to factory default enable password not reset

keith.k.quaye — Wed, 18 Jan 2012 18:43:58 GMT

Device will not respond to esc or mode button for me to do that now. This is weird

Re: Reset AP to factory default enable password not reset

Scott Fella — Wed, 18 Jan 2012 19:00:06 GMT

What shows up in the console output.

Thanks,

Scott Fella

Sent from my iPhone

Reset AP to factory default enable password not reset

keith.k.quaye — Wed, 18 Jan 2012 19:13:46 GMT

ddr init done

Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
................................................................................ ................................................................................ ................................................................................ ......
Xmodem file system is available.

DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x87000800, 0x40000000
RQDC, RFDC : 0x80000037, 0x0000020d

PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is up.
PCIE1: VC0 is active
PCIEx: initialization done
flashfs[0]: 143 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 5543936
flashfs[0]: Bytes available: 26841088
flashfs[0]: flashfs fsck took 19 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 64:9e:f3:b3:5c:84
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/c1140-k9w7-mx.124-21a.JA1/c1140-k9w7-mx.124-21a.JA1"...##############################################################################################################################################################################################################################################################################################################################################################################################################################################################################################################

File "flash:/c1140-k9w7-mx.124-21a.JA1/c1140-k9w7-mx.124-21a.JA1" uncompressed and installed, entry poi;wçGN¸¸vW7WGçwçÎ99áÃenet halted

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706

Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 18:09 by prod_rel_team

Proceeding with system init

Proceeding to unmask interrupts
Initializing flashfs...

flashfs[1]: 143 files, 7 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32385024
flashfs[1]: Bytes used: 5543936
flashfs[1]: Bytes available: 26841088
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.

Radio0 present A600 8000 90020000 0 90030000 B
Radio1 present A600 8000 98020000 0 98030000 0
Ethernet speed is 1000 Mb - FULL duplex

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-AP1142N-A-K9 (PowerPC405ex) processor (revision A0) with 98294K/32768K bytes of memory.
Processor board ID FTX1547E8D8
PowerPC405ex CPU at 586Mhz, revision number 0x147E
Last reset from watchdog timer expired
1 Gigabit Ethernet interface
2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 64:9E:F3:B3:5C:84
Part Number                          : 73-12836-03
PCA Assembly Number                  : 800-33767-03
PCA Revision Number                  : A0
PCB Serial Number                    : FOC15441UUL
Top Assembly Part Number             : 800-33775-02
Top Assembly Serial Number           : FTX1547E8D8
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1142N-A-K9

Press RETURN to get started!

*Mar 1 00:00:0
*Mar 1 00:00:11.925: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:57.018: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Mar 1 00:00:57.019: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 00:00:57.020: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar 1 00:00:57.038: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Wed 16-Sep-09 18:09 by prod_rel_team
*Mar 1 00:00:57.038: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Mar 1 00:00:58.008: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:58.018: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:58.018: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
ap>

At any rate I managed to get in I used Cisco with capital C which I swear I had done a couple of times before and it worked.

Re: Reset AP to factory default enable password not reset

Scott Fella — Wed, 18 Jan 2012 19:29:06 GMT

Haha. At least you figured it out

Thanks,

Scott Fella

Sent from my iPhone

Reset AP to factory default enable password not reset

keith.k.quaye — Wed, 18 Jan 2012 19:31:07 GMT

Thanks for your help I like it when i have someone to bounce ideas off it gives me a focus and helps troubleshoot better.

Re: Reset AP to factory default enable password not reset

Scott Fella — Wed, 18 Jan 2012 19:39:36 GMT

No problem. That's what's nice about this forum:)

Thanks,

Scott Fella

Sent from my iPhone

Reset AP to factory default enable password not reset

kristjan.edvardsson — Tue, 28 May 2013 15:14:15 GMT

I just did this for a customer. He had 1142 AP with autonomous image but password was lost.

I pressed the mode key for 5 sec and released. The ap rebooted with factory defaults, it kept the ip address

like they have usually done before.

By pressing the key for 9 seconds or more you go for a software-recovery. So be sure you need that.

You see clearly the console reports. "Mode button pressed for mor than 9 secons, waiting to be released"

then the AP takes a 10.0.0.x IP by default and broadcasts for x.tar.default image.

By having a TFTP server with 10.0.0.10 for example and the image ready, the software can be changed

from lwap to ios (autonomous) for example.