AP will not join 4402 Controller

Matthew Michaluk — Sun, 04 Jul 2021 03:32:35 GMT

Hello all,

I have a 4402 Controller and two APs that will not join. Any sugguestions would be great.

Thanks,

Matt Michaluk

AP will not join 4402 Controller

Surendra BG — Tue, 09 Aug 2011 14:54:53 GMT

Whats the AP model?? whats the WLC software version?? what does the logs say?? Without this its difficult to answer!!

Regards

Surendra

AP will not join 4402 Controller

Matthew Michaluk — Tue, 09 Aug 2011 15:15:51 GMT

AP 1250

Software Version:6.0.182.0

*Aug 08 16:57:46.235: c4:7d:4f:36:9d:20 Discovery Response sent to 10.1.50.168:62475

*Aug 08 16:57:46.235: c4:7d:4f:36:9d:20 Discovery Request from 10.1.50.168:62475

*Aug 08 16:57:46.236: c4:7d:4f:36:9d:20 Discovery Response sent to 10.1.50.168:62475

*Aug 08 16:57:46.236: c4:7d:4f:36:9d:20 Received LWAPP DISCOVERY REQUEST to 00:24:c4:13:a3:e0 on port '1'
*Aug 08 16:57:46.236: c4:7d:4f:36:9d:20 Discarding discovery request in LWAPP from AP supporting CAPWAP

AP will not join 4402 Controller

Surendra BG — Tue, 09 Aug 2011 15:20:47 GMT

Hi,

I need the complete logs.. Reboot the AP and then wait till the AP rebots on its own.. and paste the logs

Regards

Surendra

AP will not join 4402 Controller

Matthew Michaluk — Tue, 09 Aug 2011 15:47:05 GMT

Username:
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 12 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 8128512
flashfs[0]: Bytes available: 23740416
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: c4:7d:4f:39:3f:fe
Loading "flash:/c1250-k9w8-mx.124-21a.JA/c1250-k9w8-mx.124-21a.JA"...############################################################################################################################################################################################

File "flash:/c1250-k9w8-mx.124-21a.JA/c1250-k9w8-mx.124-21a.JA" uncompressed and installed, entry point: 0x3000
executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706

Cisco IOS Software, C1250 Software (C1250-K9W8-M), Version 12.4(21a)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 08-Jun-09 16:49 by prod_rel_team

Proceeding with system init

Proceeding to unmask interrupts
Initializing flashfs...

flashfs[1]: 12 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31868928
flashfs[1]: Bytes used: 8128512
flashfs[1]: Bytes available: 23740416
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.

Warning: the compile-time code checksum does not appear to be present.

Radio0 present A600 8000 A8020000 0 A8030000 30
Radio1 present A600 8000 B8020000 0 B8030000 13
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-AP1252AG-A-K9 (PowerPC 8349) processor (revision C0) with 49142K/16384K bytes of memory.
Processor board ID FTX1347912G
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from power-on
LWAPP image version 6.0.182.0
1 Gigabit Ethernet interface
2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: C4:7D:4F:39:3F:FE
Part Number                          : 73-10425-06
PCA Assembly Number                  : 800-27630-06
PCA Revision Number                  : B0
PCB Serial Number                    : FOC13450K2E
Top Assembly Part Number             : 800-29039-03
Top Assembly Serial Number           : FTX1347912G
Top Revision Number                  : A0
Product/Model Number                 : AIR-AP1252AG-A-K9
% Please define a domain-name first.

Press RETURN to get started!

*Mar 1 00:00:06.243: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.071: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:07.567: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:07.591: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 12 messages)

*Mar 1 00:00:08.539: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:09.527: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1250 Software (C1250-K9W8-M), Version 12.4(21a)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 08-Jun-09 16:49 by prod_rel_team
*Mar 1 00:00:09.527: %SNMP-5-COLDSTART: SNMP agent on host APc47d.4f39.3ffe is undergoing a cold start
*Jan 20 18:19:18.035: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Jan 20 18:19:18.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Jan 20 18:19:18.195: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Jan 20 18:19:18.195: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Jan 20 18:19:18.199: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Jan 20 18:19:18.503: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Jan 20 18:19:18.503: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jan 20 18:19:19.879: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jan 20 18:19:19.879: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Jan 20 18:19:26.911: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 10.1.50.169, mask 255.255.254.0, hostname APc47d.4f39.3ffe

*Jan 20 18:19:36.855: Logging LWAPP message to 255.255.255.255.

*Jan 20 18:19:39.551: %CDP_PD-4-POWER_OK: 16.8 W power - NEGOTIATED inline power source
*Jan 20 18:19:39.567: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Jan 20 18:19:39.583: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Jan 20 18:19:40.555: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Jan 20 18:19:40.555: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
*Jan 20 18:19:40.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (192.168.10.207) (192.168.10.204)

Translating "CISCO-LWAPP-CONTROLLER"...domain server (192.168.10.207) (192.168.10.204)

*Jan 20 18:19:47.075: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Jan 20 18:19:47.075: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Jan 20 18:19:47.075: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
*Jan 20 18:19:59.091: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Aug 9 15:44:11.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.50.21 peer_port: 5246
*Aug 9 15:44:11.999: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Aug 9 15:44:12.639: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.1.50.21 peer_port: 5246
*Aug 9 15:44:12.639: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.50.21
*Aug 9 15:44:12.639: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Aug 9 15:44:12.743: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Aug 9 15:44:12.743: %CAPWAP-3-ERRORLOG: Starting config timer
*Aug 9 15:44:12.843: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Aug 9 15:44:12.847: %CAPWAP-5-CHANGED: CAPWAP changed state to UP
*Aug 9 15:44:12.851: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Aug 9 15:44:12.855: %CAPWAP-3-ERRORLOG: CAPWAP moved to Run stopping config timer
*Aug 9 15:44:12.855: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller hornell-wlc2
*Aug 9 15:44:12.899: %LWAPP-3-CLIENTEVENTLOG: SSID HB_Corporate_Internal added to the slot[0]
*Aug 9 15:44:12.899: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset

AP will not join 4402 Controller

Surendra BG — Tue, 09 Aug 2011 15:49:31 GMT

This AP has joined the WLC hornell-wlc2

Regards

Surendra

AP will not join 4402 Controller

Matthew Michaluk — Tue, 09 Aug 2011 15:52:21 GMT

Right but it needs to join the primary controlller and not the standby. Do you know of a setting that will force it to the primay?

AP will not join 4402 Controller

Matthew Michaluk — Tue, 09 Aug 2011 16:21:02 GMT

Primary Controller

controler name

10.1.x.x

Secondary Controller

controller name

10.1.x.x

Tertiary Controller

AP will not join 4402 Controller

Surendra BG — Tue, 09 Aug 2011 16:49:54 GMT

Hi,

Force the AP from the secondary WLC to the first by making the HA settings,,

Regards

Surendra

topic AP will not join 4402 Controller in Wireless

AP will not join 4402 Controller

AP will not join 4402 Controller

AP will not join 4402 Controller

AP will not join 4402 Controller

AP will not join 4402 Controller

AP will not join 4402 Controller

AP will not join 4402 Controller

AP will not join 4402 Controller

AP will not join 4402 Controller