2702i - AP

Anukalp S — Mon, 05 Jul 2021 12:41:49 GMT

Hi.. I have a AP 2702i which I have converted it into Autonomous mode. I want to use it as standalone wifi device. I have made changes for this but the SSID which I have set is not broadcasting. SSID is not getting appeared. Am I missing anything. I am using open authentication with PSK, WPA2.

Please suggest what is missing.

Please provide the config

zdesignstudio — Mon, 22 Aug 2016 13:18:54 GMT

Please provide the config from the AP.

Please rate useful posts and mark answers as correct if applicable.

Hi,

Sandeep Choudhary — Mon, 22 Aug 2016 13:22:03 GMT

Hi,

Please use this post to configure your AP properly:

https://rscciew.wordpress.com/2014/05/24/single-ssid-configuration-on-autonomous-ap/

https://mrncciew.com/2012/10/24/multiple-ssid-config-on-autonomous-ap/

Regards

Dont forget to rate helpful posts

Please see below config.

Anukalp S — Tue, 23 Aug 2016 03:51:57 GMT

Please see below config.

ap#sh run
Building configuration...

Current configuration : 1950 bytes
!
version 15.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
!
logging rate-limit console 9
enable secret 5 $1$llsg$D.pLZVzE3b.oMBpqKpKqi/
!
no aaa new-model
no ip source-route
no ip cef
!
!
!
!
dot11 pause-time 100
dot11 syslog
!
dot11 ssid LAVAIND
   band-select
   authentication open
   authentication key-management wpa version 2
   wpa-psk ascii 7 1042080F0446405858
   information-element ssidl
!
!
!
no ipv6 cef
!
!
username Cisco password 7 0802455D0A16
!
!
bridge irb
!
!
!
interface Dot11Radio0
no ip address
shutdown
!
encryption mode ciphers aes-ccm tkip
!
ssid LAVAIND
!
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface Dot11Radio1
no ip address
shutdown
!
encryption mode ciphers aes-ccm tkip
antenna gain 0
peakdetect
no dfs band block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
!
interface GigabitEthernet0
no ip address
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
!
interface GigabitEthernet1
no ip address
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
!
interface BVI1
mac-address 5c83.8fd9.3c2c
ip address dhcp
ipv6 address dhcp
ipv6 address autoconfig
ipv6 enable
!
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
!
!
bridge 1 route ip
!
!
!
line con 0
line vty 0 4
login local
transport input all
!
end

===========================================================

ap#sh ip int
BVI1 is up, line protocol is up
Internet address is 172.16.41.20/24
Broadcast address is 255.255.255.255
Address determined by DHCP
MTU is 1500 bytes
Helper address is not set
Directed broadcast forwarding is disabled
Multicast reserved groups joined:
Outgoing access list is not set
Inbound access list is not set
Proxy ARP is enabled
Local Proxy ARP is disabled
Security level is default
Split horizon is enabled
ICMP redirects are always sent
ICMP unreachables are always sent
ICMP mask replies are never sent
IP fast switching is disabled
IP fast switching on the same interface is disabled
IP CEF switching is disabled
IP Null turbo vector
IP Null turbo vector
IP multicast fast switching is disabled
IP multicast distributed fast switching is disabled
IP route-cache flags are Fast
Router Discovery is disabled
IP output packet accounting is disabled
IP access violation accounting is disabled
TCP/IP header compression is disabled
RTP/IP header compression is disabled
Policy routing is disabled
Network address translation is disabled
BGP Policy Mapping is disabled
Input features: MCI Check
Dot11Radio0 is administratively down, line protocol is down
Internet protocol processing disabled
Dot11Radio1 is administratively down, line protocol is down
Internet protocol processing disabled
GigabitEthernet0 is up, line protocol is up
Internet protocol processing disabled
GigabitEthernet1 is up, line protocol is down
Internet protocol processing disabled

Re: Hi,

KOD — Fri, 31 Mar 2023 18:40:10 GMT

Hi,

I have done the same

just I named my AP myap
I put my domain so on the IP 192.168.1.111 = myap.mydomain.xyz

I have a SSL certificate for *.mydomain.xyz

I wish to access to https://myap.mydomain.xyz secure mode.... how or where I can upload the SSL certificate ?

I try https://www.cisco.com/c/en/us/td/docs/wireless/access_point/15-3-3-JB/configuration/guide/cg_book/cg-chap2-gui.html the part for (I think to generate a certificate) it didn't work

Many thanks in advance

Regards

topic Please see below config. in Wireless

2702i - AP

Please provide the config

Hi,

Refer link : http://www.cisco

Please see below config.

Re: Hi,