topic You will need to console into in Wireless

2602E not joining controller

roycemathew — Mon, 05 Jul 2021 09:25:13 GMT

hi All,

I have a scenario where my 2602E is not joining a controller in US. AP is in Netherlands.

AP: AIR-CAP2602E-E-K9

Logs on WLC 5508:

*spamApTask4: Jan 29 10:26:37.398: 18:9c:5d:9b:4d:00 Bridge AP can not join MultiCountry Controller: Bridge mode AP 10.130.90.11:63313 cannot be supported on Multi Country Controll
*spamApTask4: Jan 29 10:26:37.406: 18:9c:5d:9b:4d:00 State machine handler: Failed to process msg type = 3 state = 0 from 10.130.90.11:63313

is there a way i can change the bridge mode from this AP to normal or Local so that it can be useD?

Any help will be great.

thanks

Royce

You will need to console into

Scott Fella — Tue, 03 Feb 2015 16:06:40 GMT

You will need to console into that AP and erase the nvram. There is not other way to get that AP to join as its in bridge mode for some reason.

debug capwap console cli

erase /all nvram:

[confirm]

undebug all

reload

[confirm]

-Scott

so for this WAP there is no i

roycemathew — Tue, 03 Feb 2015 16:58:24 GMT

so for this WAP there is no i can just login on console and try this? i tried telnet and was not happening. So doing above will it remove bridge mode from AP?

I have a scenario where my

Leo Laohoo — Tue, 03 Feb 2015 22:36:08 GMT

I have a scenario where my 2602E is not joining a controller in US. AP is in Netherlands.

Controller in the US and the AP in the Netherlands.

So this means the WLC is configured for two different (and conflicting) regulatory domain. IF disable US from the controller will the AP join?

if i disable Country code

roycemathew — Wed, 04 Feb 2015 02:35:08 GMT

if i disable Country code from WLC wont tat also create issue with other WAP's currently working?

if i disable Country code

Leo Laohoo — Wed, 04 Feb 2015 02:43:56 GMT

if i disable Country code from WLC wont tat also create issue with other WAP's currently working?

I am suspecting the issue is that there are TWO (2) conflicting regulatory domain being configured to the WLC and this is why the European-based AP won't join the controller.

If you disable the US and enable only Europe and see if the AP joins. If the AP joins (and kicks out the US) then you know this is your answer.

you are right. thats my

roycemathew — Wed, 04 Feb 2015 02:47:06 GMT

you are right. thats my situation, as shown in my logs its due to Multi country code on WLC to accomadate European AP on a US WLC. This WAP is in Mesh mode and i wanted to know whether we have a way to get this changed to normal? if yes how.

But by disabling US country code if existing WAP's will go offline then i dont want this option.

Same thing. MESH AP will not

Leo Laohoo — Wed, 04 Feb 2015 03:28:12 GMT

Same thing. MESH AP will not support multiple and conflicting regulatory domain codes.

Just want to let you know (and ease any future "pain") that this issue is about to change since the Cisco has introduced "universal country regulatory domain" of "-UX".

The app for the iPhone can be found HERE.

For Android, it’s found HERE.

Cisco Aironet Universal AP Priming and Cisco AirProvision User Guide

This issue normally arises

Abhishek Abhishek — Tue, 17 Feb 2015 02:53:57 GMT

This issue normally arises due to mismatching regulatory domains between the controller and the AP. You need to get it synchronized.

All,i have got solution for

roycemathew — Tue, 17 Feb 2015 03:29:49 GMT

All,

i have got solution for this situation from Cisco to convert an LWAP.

Scenario: If WAP is delivered with MeshAP mode or image - this is not at all normal as per Cisco and hence this can be considered as a slip/mistake.

Steps:

#debug capwap console cli
test mesh mode local - this will change the mode from MeshAP to Local mode.

Now the WAP should join a WLC and complete the process as normal.Now we dont need to exclude the AP in AUth list.

Hope this helps someone.

check the following.

gohussai — Fri, 27 Feb 2015 18:27:41 GMT

check the following.