topic Re: 1941w - Need help with IP address assigning, and relay wirel in Wireless

1941w - Need help with IP address assigning, and relay wireless to a DHCP server.

techfactor13 — Sun, 04 Jul 2021 04:46:25 GMT

Hope someone can point me in the right direction -

Basically have a Win08 R2 DHCP server, and a 1941w router.

I've got the internet, got the lan clients getting DHCP ok (with ip helper-address set on the 0/0 internal interface).

Also have the SSID, and wireless clients can connect - but no IPs are being handed out, also not sure if I understand or did the bridging correctly or assigned IPs to the vlan or bvi1 correctly.

for ex:

DHCP server IP:

10.10.2.4

Router Ethernet internal interface 0/0 IP:

10.10.2.1

with helper-address 10.10.2.4 (lan clients are resolving IPs correctly from the DHCP server)

Vlan1 IP address:

10.10.3.1

Does this interface need the helper-address as well? (10.10.2.4)?

wlan-ap 0 IP address:

unnumbered

interface BVI1 IP address (static):

10.10.2.2

am i totally off? not even sure if i have the vlan bridged to the 0/0 adapter or not correctly - but as I said, i can get a wireless client to connect with the SSID.

would appreciate any advice/pointers, thanks

1941w - Need help with IP address assigning, and relay wireless

Stephen Rodriguez — Mon, 12 Mar 2012 13:06:23 GMT

can you post the config of the router and AP?

1941w - Need help with IP address assigning, and relay wireless

techfactor13 — Mon, 12 Mar 2012 16:00:35 GMT

of course - here is the router config:

=======================================================

Using 5591 out of 262136 bytes

version 15.1

no service pad

service tcp-keepalives-in

service tcp-keepalives-out

service timestamps debug datetime msec localtime show-timezone

service timestamps log datetime msec localtime show-timezone

service password-encryption

service sequence-numbers

hostname router

boot-start-marker

boot-end-marker

security authentication failure rate 3 log

security passwords min-length 6

logging buffered 51200

logging console critical

enable secret 5 $1$JWwK$.04.NFg7tQ82UTy68/hyv.

no aaa new-model

service-module wlan-ap 0 bootimage autonomous

no ipv6 cef

no ip source-route

ip cef

no ip bootp server

ip name-server 10.10.2.4

multilink bundle-name authenticated

crypto pki token default removal timeout 0

crypto pki trustpoint TP-self-signed-975501586

enrollment selfsigned

subject-name cn=IOS-Self-Signed-Certificate-975501586

revocation-check none

rsakeypair TP-self-signed-975501586

crypto pki certificate chain TP-self-signed-975501586

certificate self-signed 01 nvram:IOS-Self-Sig#3.cer

license udi pid CISCO1941W-A/K9 sn FTX155085QG

hw-module ism 0

ip tcp synwait-time 10

ip ssh time-out 60

ip ssh authentication-retries 2

interface Embedded-Service-Engine0/0

no ip address

no ip redirects

no ip unreachables

no ip proxy-arp

ip flow ingress

shutdown

interface GigabitEthernet0/0

description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$$ES_LAN$$FW_INSIDE$

ip address 10.10.2.1 255.255.255.0

ip helper-address 10.10.2.4

no ip redirects

no ip unreachables

no ip proxy-arp

ip flow ingress

ip nat inside

ip virtual-reassembly in

duplex auto

speed auto

no mop enabled

interface wlan-ap0

description Service module interface to manage the embedded AP

ip unnumbered GigabitEthernet0/0

no ip redirects

no ip unreachables

no ip proxy-arp

ip flow ingress

arp timeout 0

no mop enabled

no mop sysid

interface GigabitEthernet0/1

description $ES_WAN$$FW_OUTSIDE$

ip address dhcp client-id GigabitEthernet0/1

no ip redirects

no ip unreachables

no ip proxy-arp

ip flow ingress

ip nat outside

ip virtual-reassembly in

duplex auto

speed auto

no mop enabled

interface Wlan-GigabitEthernet0/0

description Internal switch interface connecting to the embedded AP

no ip address

interface Vlan1

ip address 10.10.3.1 255.255.255.0

ip helper-address 10.10.2.4

no ip redirects

no ip unreachables

no ip proxy-arp

ip flow ingress

ip forward-protocol nd

ip http server

ip http authentication local

ip http secure-server

ip http timeout-policy idle 60 life 86400 requests 10000

ip nat inside source list 1 interface GigabitEthernet0/1 overload

logging trap debugging

access-list 1 remark INSIDE_IF=GigabitEthernet0/0

access-list 1 remark CCP_ACL Category=2

access-list 1 permit 10.10.2.0 0.0.0.255

no cdp run

control-plane

line con 0

transport output telnet

line aux 0

transport output telnet

line 2

no activation-character

no exec

transport preferred none

transport input all

transport output pad telnet rlogin lapb-ta mop udptn v120 ssh

stopbits 1

line 67

no activation-character

no exec

transport preferred none

transport input all

transport output pad telnet rlogin lapb-ta mop udptn v120 ssh

line vty 0 4

privilege level 15

transport input telnet ssh

line vty 5 15

privilege level 15

transport input telnet ssh

scheduler allocate 20000 1000

end

=======================================================

and the ap config:

=======================================================

Using 2067 out of 32768 bytes

version 12.4

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

hostname ap

enable secret 5 $1$xKDT$GdLGeA6h.H9LKL9l3dPmj.

no aaa new-model

dot11 syslog

dot11 ssid WIFI1

vlan 1

authentication open

authentication key-management wpa

mbssid guest-mode

wpa-psk ascii 7 044B1E030D2D43632A

bridge irb

interface Dot11Radio0

no ip address

no ip route-cache

encryption vlan 1 mode ciphers aes-ccm

broadcast-key vlan 1 change 30

ssid WIFI1

antenna gain 0

station-role root

interface Dot11Radio0.1

encapsulation dot1Q 1 native

no ip route-cache

bridge-group 2

bridge-group 2 subscriber-loop-control

bridge-group 2 block-unknown-source

no bridge-group 2 source-learning

no bridge-group 2 unicast-flooding

bridge-group 2 spanning-disabled

interface Dot11Radio1

no ip address

no ip route-cache

encryption vlan 1 mode ciphers aes-ccm

broadcast-key vlan 1 change 30

ssid WIFI1

antenna gain 0

dfs band 3 block

channel dfs

station-role root

interface Dot11Radio1.1

encapsulation dot1Q 1 native

no ip route-cache

bridge-group 2

bridge-group 2 subscriber-loop-control

bridge-group 2 block-unknown-source

no bridge-group 2 source-learning

no bridge-group 2 unicast-flooding

bridge-group 2 spanning-disabled

interface GigabitEthernet0

description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router

no ip address

no ip route-cache

interface GigabitEthernet0.1

encapsulation dot1Q 1 native

no ip route-cache

bridge-group 1

no bridge-group 1 source-learning

bridge-group 1 spanning-disabled

interface BVI1

ip address 10.10.2.2 255.255.255.0

no ip route-cache

ip http server

no ip http secure-server

ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

bridge 1 route ip

line con 0

no activation-character

line vty 0 4

end

============================================

1941w - Need help with IP address assigning, and relay wireless

Stephen Rodriguez — Mon, 12 Mar 2012 16:10:27 GMT

ok, so a couple of things.

interface Wlan-GigabitEthernet0/0

description Internal switch interface connecting to the embedded AP

no ip address

This tells me that the AP is going to be in VLAN 1, 10.10.3.x/24, but the AP has a static IP that doesn't match.

Then under the Radio subinterfaces, you call encapsulation dot1q 1 native, but are linked to bridge-group 2. When you issue the native command, it should place that interface in bridge-group 1.

So to fix this.

Conf t

interface Dot11Radio0.1

bridge-group 1

interface Dot11Radio1.1

bridge-group 1

exit

Interface BVI 1

ip address dhcp ( or set a 10.10.3.x address)

end

Steve

1941w - Need help with IP address assigning, and relay wireless

techfactor13 — Mon, 12 Mar 2012 16:44:22 GMT

excellent! that worked for passing through dhcp but i have one problem left -

i get all the settings, but there is a problem with getting the internet

i can't ping ip addresses or domain names.

set up manual DNS entries on a wireless client and still nothing.

changed to all manual settings (ip address in the 10.10.2.0 range and the 10.10.3.0 range)

no successful pings.

1941w - Need help with IP address assigning, and relay wireless

techfactor13 — Mon, 12 Mar 2012 16:45:35 GMT

to clarify - the wired lan clients get the internet - dns resolves correctly.

the wireless clients do not resolve or ping successfully

1941w - Need help with IP address assigning, and relay wireless

Stephen Rodriguez — Mon, 12 Mar 2012 16:53:55 GMT

ok, so the client should be getting 10.10.3.x address space.

You need to add ip nat inside to VLAN 1, and add add the 10.10.3.0 to the NAT ACL

Current config only shows 10.10.2.0 in the permit list:

access-list 1 remark INSIDE_IF=GigabitEthernet0/0

access-list 1 remark CCP_ACL Category=2

access-list 1 permit 10.10.2.0 0.0.0.255

conf t

interface VLAN 1

ip nat inside

exit

access-list 1 permit 10.10.3.0 0.0.0.255

end

once that is done, you should be able to get the wireless cliens out to the interwebs.

Steve

1941w - Need help with IP address assigning, and relay wireless

techfactor13 — Mon, 12 Mar 2012 17:11:58 GMT

was pulling that up the same time i saw your post.

added the entry - it's now picking up the correct dns suffix in ipconfig

but still no ping or domain resolution on the wireless clients.

====================================================

ip nat inside source list 1 interface GigabitEthernet0/1 overload

logging trap debugging

access-list 1 remark INSIDE_IF=GigabitEthernet0/0

access-list 1 remark CCP_ACL Category=2

access-list 1 permit 10.10.2.0 0.0.0.255

access-list 1 permit 10.10.3.0 0.0.0.255

Re: 1941w - Need help with IP address assigning, and relay wirel

techfactor13 — Mon, 12 Mar 2012 17:12:52 GMT

i am pinging the entire internal network successfully with wireless and wired

both with ip address and machine name

1941w - Need help with IP address assigning, and relay wireless

Stephen Rodriguez — Mon, 12 Mar 2012 17:13:15 GMT

and you added the ip nat inside to the VLAN 1?

Can you post the current config from the router?

Steve

Re: 1941w - Need help with IP address assigning, and relay wirel

techfactor13 — Mon, 12 Mar 2012 17:34:25 GMT

yeah i did both -

current config

========================================

Current configuration : 7040 bytes

version 15.1

no service pad

service tcp-keepalives-in

service tcp-keepalives-out

service timestamps debug datetime msec localtime show-timezone

service timestamps log datetime msec localtime show-timezone

service password-encryption

service sequence-numbers

hostname router

boot-start-marker

boot-end-marker

security authentication failure rate 3 log

security passwords min-length 6

logging buffered 51200

logging console critical

enable secret 5 $1$JWwK$.04.NFg7tQ82UTy68/hyv.

no aaa new-model

service-module wlan-ap 0 bootimage autonomous

no ipv6 cef

no ip source-route

ip cef

no ip bootp server

ip name-server 10.10.2.4

multilink bundle-name authenticated

crypto pki token default removal timeout 0

crypto pki trustpoint TP-self-signed-975501586

enrollment selfsigned

subject-name cn=IOS-Self-Signed-Certificate-975501586

revocation-check none

rsakeypair TP-self-signed-975501586

hw-module ism 0

ip tcp synwait-time 10

ip ssh time-out 60

ip ssh authentication-retries 2

interface Embedded-Service-Engine0/0

no ip address

no ip redirects

no ip unreachables

no ip proxy-arp

ip flow ingress

shutdown

interface GigabitEthernet0/0

description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$$ES_LAN$$FW_INSIDE$

ip address 10.10.2.1 255.255.255.0

ip helper-address 10.10.2.4

no ip redirects

no ip unreachables

no ip proxy-arp

ip flow ingress

ip nat inside

ip virtual-reassembly in

duplex auto

speed auto

no mop enabled

interface wlan-ap0

description Service module interface to manage the embedded AP

ip unnumbered GigabitEthernet0/0

no ip redirects

no ip unreachables

no ip proxy-arp

ip flow ingress

arp timeout 0

no mop enabled

no mop sysid

interface GigabitEthernet0/1

description $ES_WAN$$FW_OUTSIDE$$ETH-WAN$

ip address dhcp client-id GigabitEthernet0/1

no ip redirects

no ip unreachables

no ip proxy-arp

ip flow ingress

ip nat outside

ip virtual-reassembly in

duplex auto

speed auto

no mop enabled

interface Wlan-GigabitEthernet0/0

description Internal switch interface connecting to the embedded AP

no ip address

interface Vlan1

ip address 10.10.3.1 255.255.255.0

ip helper-address 10.10.2.4

no ip redirects

no ip unreachables

no ip proxy-arp

ip flow ingress

ip nat inside

ip virtual-reassembly in

ip forward-protocol nd

ip http server

ip http authentication local

ip http secure-server

ip http timeout-policy idle 60 life 86400 requests 10000

ip nat inside source list 1 interface GigabitEthernet0/1 overload

logging trap debugging

access-list 1 remark INSIDE_IF=GigabitEthernet0/0

access-list 1 remark CCP_ACL Category=2

access-list 1 permit 10.10.2.0 0.0.0.255

access-list 1 remark WLAN

access-list 1 permit 10.10.3.0 0.0.0.255

no cdp run

control-plane

line con 0

transport output telnet

line aux 0

transport output telnet

line 2

no activation-character

no exec

transport preferred none

transport input all

transport output pad telnet rlogin lapb-ta mop udptn v120 ssh

stopbits 1

line 67

no activation-character

no exec

transport preferred none

transport input all

transport output pad telnet rlogin lapb-ta mop udptn v120 ssh

line vty 0 4

privilege level 15

transport input telnet ssh

line vty 5 15

privilege level 15

transport input telnet ssh

scheduler allocate 20000 1000

end

Re: 1941w - Need help with IP address assigning, and relay wirel

Stephen Rodriguez — Mon, 12 Mar 2012 17:51:07 GMT

what happens if you do a source ping from the vlan 1 interface? can you traceroute from the client to an address?

Re: 1941w - Need help with IP address assigning, and relay wirel

techfactor13 — Mon, 12 Mar 2012 18:07:11 GMT

traceroute from client - request timed out with DHCP settings.

source ping from 10.10.3.1 succeeds to outside ip

changing a wireless client to the 10.10.3.0 range also successful outside ping.

actually the wireless client gets internet with an 10.10.3.0 range and using the internal DNS server (10.10.2.4)

tracert with the 10.10.3.0 range first hop is 10.10.3.1 == successful.

Re: 1941w - Need help with IP address assigning, and relay wirel

Stephen Rodriguez — Mon, 12 Mar 2012 18:14:37 GMT

what do you mean changing the wireless to a 10.10.3.x address?

The AP is linked to VLAN 1/10.10.3.0. What address are you assigning to the clients?

Do you want them to be in a different subnet?

Steve

Re: 1941w - Need help with IP address assigning, and relay wirel

techfactor13 — Mon, 12 Mar 2012 18:20:57 GMT

just testing, no don't want the wireless clients to be in a different subnet.

didn't change anything on the router/ap config

just tested a wireless client with a random ip from the 10.10.3.0 range

ip settings on client:

ip: 10.10.3.25/24

gateway: 10.10.3.1 (the vlan1)

dns: 10.10.2.4

got internet access.

when dhcp is assigned:

10.10.2.xx/24

gateway: 10.10.2.1

dns: 10.10.2.4

no internet access on wireless clients.

Re: 1941w - Need help with IP address assigning, and relay wirel

Stephen Rodriguez — Mon, 12 Mar 2012 18:25:56 GMT

the client shouldn't be getting an address in 10.10.2.x subnet, as the DHCP request should be encapsulated with 10.10.3.1 when it's sent to the server. So it should get 10.10.3 from teh server, or no address if there is not a scope configured.

Steve

Re: 1941w - Need help with IP address assigning, and relay wirel

techfactor13 — Mon, 12 Mar 2012 18:29:58 GMT

currently when the wireless client gets a dhcp assignment - it is assigned from the 10.10.2.x subnet

i.e. wireless client

10.10.2.xx

gate: 10.10.2.1

dns: 10.10.2.4 (dhcp/dns server)

Re: 1941w - Need help with IP address assigning, and relay wirel

techfactor13 — Mon, 12 Mar 2012 18:32:10 GMT

do i need a 10.10.3.x scope on the DHCP server?

is there a need for the 'ip helper-address 10.10.2.4' entry on the vlan1?

Re: 1941w - Need help with IP address assigning, and relay wirel

Stephen Rodriguez — Mon, 12 Mar 2012 18:35:21 GMT

you could put the scope on the router, but if you have a server available that would work as well.

What could be happening, is that the client is not getting a new DHCP address and it's holding on to it's old one.

The ip helper will be needed on the VLAN 1 interface, as it tells the interface where to send a DHCP request.

Steve

Re: 1941w - Need help with IP address assigning, and relay wirel

techfactor13 — Mon, 12 Mar 2012 18:41:58 GMT

thought there might be something like that (holding on to the old ip) so before i tested i not only uninstalled/reinstall the net adapter, i flushed dns, and reset the tcp/ip stack... plus i forced an exclusion on the DHCP server to push new ip addresses

still got an ip in the 10.10.2.x range

would it work to put a dhcp scope on the router, would the wireless clients still get a 10.10.2.x ip address and be able to connect to the 10.10.2.x subnet?