Configuring 881W wireless

thefilmguy — Sun, 04 Jul 2021 04:41:35 GMT

I'm having trouble configuring my router for wireless. I have followed guides but with no luck. Right now my issue is below with the radio. I cannot figure out why this is stuck in reset. I have reloaded the AP with no luck. Any suggestions? Config is posted below.

Interface IP-Address OK? Method Status Protocol

BVI1 10.20.50.35 YES DHCP up up

Dot11Radio0 unassigned YES NVRAM reset down

GigabitEthernet0 unassigned YES NVRAM up up

GigabitEthernet0.2 unassigned YES unset up up

CONFIG

########################ROUTER#######################

Current configuration : 5422 bytes

! Last configuration change at 18:55:56 PCTime Wed Feb 29 2012 by msetnes

! NVRAM config last updated at 18:37:40 PCTime Wed Feb 29 2012 by msetnes

version 15.1

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

hostname XXXXXX

boot-start-marker

boot-end-marker

aaa new-model

aaa authentication login ciscocp_vpn_xauth_ml_1 local

aaa authorization network ciscocp_vpn_group_ml_1 local

aaa session-id common

memory-size iomem 10

clock timezone PCTime -6 0

clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00

ip source-route

ip dhcp excluded-address 10.20.30.1 10.20.30.99

ip dhcp excluded-address 10.20.50.1 10.20.50.31

ip dhcp pool LOCAL

import all

network 10.20.30.0 255.255.255.0

default-router 10.20.30.1

dns-server 8.8.8.8 8.8.4.4

ip dhcp pool WIFI

import all

network 10.20.50.0 255.255.255.0

default-router 10.20.30.1

dns-server 8.8.8.8 8.8.4.4

ip cef

ip name-server 8.8.8.8

ip name-server 8.8.4.4

no ipv6 cef

username XXXXXX privilege 15 secret 5 XXXXXXXX

ip ssh time-out 60

ip ssh authentication-retries 2

ip ssh version 1

bridge irb

interface FastEthernet0

no ip address

interface FastEthernet1

no ip address

interface FastEthernet2

no ip address

interface FastEthernet3

no ip address

interface FastEthernet4

description "Connection to internet"

ip address dhcp client-id FastEthernet4

ip flow ingress

ip nat outside

ip virtual-reassembly in

duplex auto

speed auto

interface wlan-ap0

description "Service module interface connecting to embedded AP"

ip unnumbered Vlan2

arp timeout 0

interface Wlan-GigabitEthernet0

description "Internal switch interface connecting to AP"

switchport trunk native vlan 2

switchport mode trunk

interface Vlan1

description "Local"

ip address 10.20.30.1 255.255.255.0

ip flow ingress

ip nat inside

ip virtual-reassembly in

interface Vlan2

description "Wireless"

ip address 10.20.50.1 255.255.255.0

ip flow ingress

ip nat inside

ip virtual-reassembly in

ip forward-protocol nd

ip http server

ip http access-class 23

ip http authentication local

ip http secure-server

ip http timeout-policy idle 60 life 86400 requests 10000

ip nat inside source list 23 interface FastEthernet4 overload

ip route 0.0.0.0 0.0.0.0 dhcp

logging esm config

access-list 22 remark

access-list 23 permit 10.20.30.0 0.0.0.255

access-list 23 permit 10.20.50.0 0.0.0.255

control-plane

bridge 1 protocol ieee

bridge 1 route ip

line con 0

no modem enable

line aux 0

line 2

no activation-character

no exec

transport preferred none

transport input all

line vty 0 4

exec-timeout 5 0

transport input all

transport output all

end

#########################AP##########################

dot11 ssid XXXXXX

authentication open

guest-mode

username XXXXXX privilege 15 secret 5 XXXXXX

bridge irb

interface Dot11Radio0

no ip address

no ip route-cache

ssid SkyNET

speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

interface GigabitEthernet0

description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router

no ip address

no ip route-cache

bridge-group 1

no bridge-group 1 source-learning

bridge-group 1 spanning-disabled

interface BVI1

ip address dhcp

no ip route-cache

ip default-gateway 10.20.30.1

ip http server

no ip http secure-server

ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

bridge 1 route ip

line con 0

privilege level 15

no activation-character

line vty 0 4

end

Re: Configuring 881W wireless

Stephen Rodriguez — Thu, 01 Mar 2012 01:34:30 GMT

when you define the VLAN under the SSID you need ti create the sub interface under the radio as well.

If your only going to have the one SSID the you can remove the VLAN from under the said and encryption statement.

Steve

Sent from Cisco Technical Support iPhone App

Re: Configuring 881W wireless

thefilmguy — Thu, 01 Mar 2012 01:56:48 GMT

Thanks, this brought the radio back up. I seem to be connecting and disconnecting consistently. Is there something I'm missing in my config?

EDIT--

I removed encryption just to resolve this issue for now. My issue now is I am not able to talk outside of the wifi network. I can only ping within the 10.20.50.0 network.

Re: Configuring 881W wireless

Stephen Rodriguez — Thu, 01 Mar 2012 02:11:03 GMT

nothing I'm noticing of the top of my head. Can you be more specific with the issue? Do you get an up address the drop or do you not get that far?

Sent from Cisco Technical Support iPhone App

Re: Configuring 881W wireless

thefilmguy — Thu, 01 Mar 2012 02:18:41 GMT

I receive an IP address (10.20.50.36) I can only ping this wireless IP within the AP and router, nowhere else.

Re: Configuring 881W wireless

Stephen Rodriguez — Thu, 01 Mar 2012 02:21:53 GMT

check your GW address according to your scope it's 10.20.30.1 which is VLAN 1. It should be 10.20.50.1 the VLAN 2 address.

Steve

Sent from Cisco Technical Support iPad App

Configuring 881W wireless

thefilmguy — Thu, 01 Mar 2012 02:30:11 GMT

I've corrected the default gateway on the AP to no avail. I still cannot talk between wireless and wired clients, as well as not being able to reach outside the network with WiFi.

Re: Configuring 881W wireless

Stephen Rodriguez — Thu, 01 Mar 2012 02:39:34 GMT

not the AP, but that one too. The GW in your dhcp scope is showing the wrong IP

Sent from Cisco Technical Support iPad App

Configuring 881W wireless

thefilmguy — Thu, 01 Mar 2012 02:48:14 GMT

Removing the VLAN and encryption statements under dot11 ssid resolved the connecting issue

Changing the DHCP scope default router to 10.20.501 resolved the communication issue.

Both networks can talk now and both and reach externally.

Thanks Stephen, much appreciated.

topic Re: Configuring 881W wireless in Wireless

Configuring 881W wireless

Re: Configuring 881W wireless

Re: Configuring 881W wireless

Re: Configuring 881W wireless

Re: Configuring 881W wireless

Re: Configuring 881W wireless

Configuring 881W wireless

Re: Configuring 881W wireless

Configuring 881W wireless