topic Re: Cisco AIR CAP3502I E K9--- standalone Config in Wireless

Cisco AIR CAP3502I E K9--- standalone Config

muzecisco — Sun, 04 Jul 2021 04:06:33 GMT

Hello good people. I have recently bought Cisco AIR CAP3502I E K9 but i am seeing that it can only work with WLAN controller. How can I make it work as a stand alone.

Your help will be appreciated.

Cisco AIR CAP3502I E K9--- standalone Config

muzecisco — Mon, 21 Nov 2011 15:50:04 GMT

Any good links on how i can start configuring it as standalone WAP

Re: Cisco AIR CAP3502I E K9--- standalone Config

Scott Fella — Mon, 21 Nov 2011 15:51:11 GMT

You can use the 1260 autonomous code if you want. Just remember, this isn't supported by Cisco but it will work.

Sent from my iPhone

Cisco AIR CAP3502I E K9--- standalone Config

Surendra BG — Mon, 21 Nov 2011 15:52:50 GMT

U can convert but not supported by TAC!!

use the below link..

https://supportforums.cisco.com/docs/DOC-14960

Please dont forget to rate the usefull posts!!

Regards

Surendra

Re: Cisco AIR CAP3502I E K9--- standalone Config

Scott Fella — Mon, 21 Nov 2011 15:54:11 GMT

Take a look at this

https://supportforums.cisco.com/docs/DOC-20537

Sent from my iPhone

Re: Cisco AIR CAP3502I E K9--- standalone Config

muzecisco — Wed, 30 Nov 2011 10:45:54 GMT

Scott whats the autonomous code 1260 for and how is it used. I have never confugured a cisco wirelsess AP

Re: Cisco AIR CAP3502I E K9--- standalone Config

muzecisco — Wed, 30 Nov 2011 12:43:41 GMT

This information is so helpful. Last part is where can i get

cisco IOS for 1260 ap3g1-k9w7-tar.124-25d.JA1

Don have smartnet account

Cisco AIR CAP3502I E K9--- standalone Config

Scott Fella — Wed, 30 Nov 2011 13:33:52 GMT

Send me an email you on that.

Cisco AIR CAP3502I E K9--- standalone Config

muzecisco — Wed, 30 Nov 2011 15:09:47 GMT

muzendaf@gmail.com

Cisco AIR CAP3502I E K9--- standalone Config

muzecisco — Thu, 01 Dec 2011 07:36:14 GMT

Team confirm that after this conversion to standalone it can pass traffic. I have read some text which say it cannot pass traffic.

Re: Cisco AIR CAP3502I E K9--- standalone Config

Scott Fella — Thu, 01 Dec 2011 07:41:02 GMT

Where did you read that? You should have no issue since the 3502 radios are the same as the 1260. You just won't have the full feature of the 3502.

Sent from Cisco Technical Support iPhone App

Re: Cisco AIR CAP3502I E K9--- standalone Config

Scott Fella — Thu, 01 Dec 2011 07:44:52 GMT

Here is a link from George's blog page

http://www.my80211.com/home/2011/11/18/autonomous-ios-support-for-3500-and-3600-series-access-point.html

Sent from Cisco Technical Support iPhone App

Cisco AIR CAP3502I E K9--- standalone Config

muzecisco — Thu, 01 Dec 2011 07:44:56 GMT

Thanks Fella.

Any document showing how to finish off the configs after the IOS chnage. The howto docs for 1260/3502 for stand alone most i am seeing are for controller based. Have never setup a cisco WAP but i understanda and am into cisco

Re: Cisco AIR CAP3502I E K9--- standalone Config

Scott Fella — Thu, 01 Dec 2011 07:48:25 GMT

You can reference this guide for the 1140

http://www.cisco.com/en/US/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html

http://www.cisco.com/en/US/docs/wireless/access_point/12.3_7_JA/configuration/guide/s37ssid.html

http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008055c39a.shtml

Sent from Cisco Technical Support iPhone App

Cisco AIR CAP3502I E K9--- standalone Config

muzecisco — Wed, 07 Dec 2011 11:56:01 GMT

I am still having troubles with this issue.

Scott kindly resend the image again as it should be uploaded.

Another challenges is setting the ip address go g0 interface. Even though i do that manually dhcp continues to discard the manual n gets smthing from my dhcp since it will continously look for WController.

How do i sort this out.

I have also failed to access the GUI thru the private ip add

Cisco AIR CAP3502I E K9--- standalone Config

muzecisco — Wed, 07 Dec 2011 14:47:12 GMT

Looks like the file is now extracting. Thanks Scott.

one last problem is how do i stop renew of IP address.

I have assigned the address manually but its being overwritten by the DHCP ip which renews afters a minute.

Solving this should make me a happy man.

Re: Cisco AIR CAP3502I E K9--- standalone Config

Scott Fella — Wed, 07 Dec 2011 15:19:41 GMT

Here is how to configure an ip address to the bvi1 interface.

Command

Purpose

Step 1

configure terminal

Enter global configuration mode.

Step 2

interface bvi1

Enters interface configuration mode for the BVI.

Step 3

ip address ip_address net_mask

Assigns an IP address and subnet mask address to the BVI.

http://www.cisco.com/en/US/docs/wireless/access_point/1140/autonomous/getting_started/guide/ap1140aut_getstart.html#wp42920

Sent from my iPhone

Cisco AIR CAP3502I E K9--- standalone Config

muzecisco — Tue, 07 Feb 2012 08:15:45 GMT

Happy New year,

My 3502 AP is not accepting config t

on show int brief its also showing Ge0 only and no bvi is shown.

What do i need to do for it to accept config t command

Cisco AIR CAP3502I E K9--- standalone Config

muzecisco — Tue, 07 Feb 2012 08:49:22 GMT

I have entered the following command

debug capwap console cli

and have manged to configure the ip address for Ge0 manually

This address is however renewed after some few minutes to a dhcp assigned which is also continously renewed.

What should i do to stabilise this assignment.

Cisco AIR CAP3502I E K9--- standalone Config

Leo Laohoo — Tue, 07 Feb 2012 10:19:46 GMT

What do i need to do for it to accept config t command

What are you trying to do? 3500 does NOT "support" autonomous IOS. When I mean "support", I mean you can load autonomous IOS but don't get Cisco TAC to help you with any configuration issues.