topic Re: Configuring AIR-WLC4402-50-K9 through CLI in Wireless

Configuring AIR-WLC4402-50-K9 through CLI

decrypted08 — Sun, 04 Jul 2021 02:31:58 GMT

I have many AIR-WLC4402-50-K9 devices to configure and the cli is frusterating- does anyone have a link to a step by step document that walks through assigning an IP, SSID, and enabling the radios using the cli? I cant seem to find one that works completly. I just need to assign it an ip so I can use the web gui!

Thnaks

Re: Configuring AIR-WLC4402-50-K9 through CLI

Surendra BG — Fri, 10 Dec 2010 17:02:24 GMT

Hi,

This is the command to assign the IP address...

CONFIG INTERFACE ADDRESS MANAGEMENT

CONFIG INTERFACE ADDRESS MANAGEMENT 10.10.10.224 255.255.255.0 10.10.10.1

CONFIG INTERFACE ADDRESS AP-MANAGER 10.10.10.224 255.255.255.0 10.10.10.1

Then issue the commandto enable WEB access and TELNET access.

CONFIG NETWORK WEBMODE ENABLE

CONFIG NETWORK TELNET ENABLE

Here is the link which gives info on the complete command guide for WLC... (This needs CCO login to view)

http://www.cisco.com/en/US/partner/docs/wireless/controller/6.0/command/reference/cli60.html#wp1321947

Lemme know if this answered your question..

Regards

Surendra

===

Please rate the posts which answered your quiestion or was helpfull

Re: Configuring AIR-WLC4402-50-K9 through CLI

Surendra BG — Fri, 10 Dec 2010 17:04:37 GMT

oops sorry.. the AP-MANAGER should be assigned to a different ip.. here is the example again..

CONFIG INTERFACE ADDRESS MANAGEMENT 10.10.10.224 255.255.255.0 10.10.10.1

CONFIG INTERFACE ADDRESS AP-MANAGER 10.10.10.223 255.255.255.0 10.10.10.1

then

CONFIG NETWORK WEBMODE ENABLE

CONFIG NETWORK TELNET ENABLE

Lemme know if this answered your question..

Regards

Surendra

===

Please rate the posts which answered your quiestion or was helpfull

Re: Configuring AIR-WLC4402-50-K9 through CLI

decrypted08 — Fri, 10 Dec 2010 17:14:28 GMT

it doesnt work:

I have to start in an elevated mode right?

enable - password - right? then what? configure radio0 ...... ?

Re: Configuring AIR-WLC4402-50-K9 through CLI

Surendra BG — Fri, 10 Dec 2010 17:18:29 GMT

The WLC CLI is completely different.. the command which i provided will help you out.. here is the command.. There is no En or dot11 0 commands on the WLC CLI..

(Cisco Controller) >

(Cisco Controller) > CONFIG INTERFACE ADDRESS MANAGEMENT 10.10.10.224 255.255.255.0 10.10.10.1

(Cisco Controller) > CONFIG INTERFACE ADDRESS AP-MANAGER 10.10.10.223 255.255.255.0 10.10.10.1

(Cisco Controller) > CONFIG NETWORK WEBMODE ENABLE

(Cisco Controller) > CONFIG NETWORK TELNET ENABLE

Lemme know if this answered your question..

Regards

Surendra

===

Please rate the posts which answered your quiestion or was helpfull

Re: Configuring AIR-WLC4402-50-K9 through CLI

decrypted08 — Fri, 10 Dec 2010 17:20:29 GMT

Oh! I am so sorry, I ment the access point not the wlc- err my appologies, its the

1130ag access point im connected to!

Re: Configuring AIR-WLC4402-50-K9 through CLI

Surendra BG — Fri, 10 Dec 2010 17:33:05 GMT

AP is in Autonomous mode or in LWAPP mode?? i mean you do not want to use WLC right??

If its in Autononmous mode.. then the below command will help you..

AP>en

password:

ap#conf t

ap(conf t)#int bvi 1

ap(conf-if)#ip address

ap(conft-if)#no shut

ap(conft-if)#exit

ap(conf t)#ip default-gateway

ap(conf t)#end

Example..

AP>en

password:

ap#conf t

ap(conf t)#int bvi 1

ap(conf-if)#ip address 10.0.0.2 255.255.255.0

ap(conft-if)#no shut

ap(conft-if)#exit

ap(conf t)#ip default-gateway 10.0.0.1

This will help you!!

if you are not able to go to the CONFIG mode after entering the command CONFIG T, then the AP will be in LWAPP mode and you need to convert the same to Autonomous.. here is the link..

https://supportforums.cisco.com/thread/2055997

Lemme know if this answered your question..

Regards

Surendra

===

Please rate the posts which answered your quiestion or was helpfull

Regards
Surendra

Re: Configuring AIR-WLC4402-50-K9 through CLI

Surendra BG — Fri, 10 Dec 2010 17:46:20 GMT

Everythings working??

lemme know if this answered your question..

Regards

Surendra

========

Please dont forget to rate the post if this answered your question or was helpfull

Re: Configuring AIR-WLC4402-50-K9 through CLI

decrypted08 — Fri, 10 Dec 2010 17:46:59 GMT

Ok so this configured the ip of the bridge interface, i still need to assign a SSID and enable the radios right?

Re: Configuring AIR-WLC4402-50-K9 through CLI

decrypted08 — Fri, 10 Dec 2010 17:51:17 GMT

Well no, Its not broadcasting anything- thought the interface ip is configured

Re: Configuring AIR-WLC4402-50-K9 through CLI

Surendra BG — Fri, 10 Dec 2010 17:52:19 GMT

ok.. i tot this post is for getting the GUI access.. is that right?? now u can iopen up the browser and hit the BVI ip and then you can get the access to the GUI..

here is the link to configure WPA auth and SSID..

The below link will help you out in getting the basic wireless config on the AP..

http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008055c39a.shtml

here is the link for WPA-2 PSK as well

https://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008054339e.shtml#pers

Lemme know if this answered your question..

Regards

Surendra

===

Please dont forget to rate the posts which answered your quiestion or was helpfull

Re: Configuring AIR-WLC4402-50-K9 through CLI

Surendra BG — Fri, 10 Dec 2010 17:53:46 GMT

Thats because you have not configured anything.. please have a look into my previous reply and lemme know how this works

Regards

Surendra

Re: Configuring AIR-WLC4402-50-K9 through CLI

decrypted08 — Fri, 10 Dec 2010 18:10:52 GMT

I still cannot get access to the AP- i configured an SSID of TEST assigned radio

0 and 1 ip address but there is nothing broadcasting for me to connect to! How can i access the gui

wirelessly ( i dont have a crossover cable)

Re: Configuring AIR-WLC4402-50-K9 through CLI

decrypted08 — Fri, 10 Dec 2010 18:16:47 GMT

after show conf- it looks like radio is up and with an ssid but i dont see any available in wireless network to connec

t to to get to the gui...

!
interface Dot11Radio0
ip address 10.10.10.100 255.255.255.0
no ip route-cache
!
ssid test
!
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled...

interface BVI1
ip address 10.10.10.5 255.255.255.0
no ip route-cache

Re: Configuring AIR-WLC4402-50-K9 through CLI

Surendra BG — Fri, 10 Dec 2010 18:18:14 GMT

if you have the access to the AP CLI.. then issue the below command..

conf t

dot11 ssid

GUEST-MODE >>>>>>. This command will bradcast the SSID

end

wr >>> To save the config..

Regards
Surendra

Re: Configuring AIR-WLC4402-50-K9 through CLI

Surendra BG — Fri, 10 Dec 2010 18:20:12 GMT

dont assign IP to "interface dot11 0 "

it should be like this..

nterface Dot11Radio0
no ip address
no ip route-cache
!
ssid test
!
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled...

Re: Configuring AIR-WLC4402-50-K9 through CLI

decrypted08 — Fri, 10 Dec 2010 18:34:33 GMT

To clafiry-

1: I am conencted to the AP through a console cable-

2: I am trying to gain web gui access wirelessly

3: the ap is configured as so:

ap#show conf
Using 1498 out of 32768 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
enable secret 5 $1$hDfR$kvTnx/C3JJ0KOqrQzgwuY1
!
no aaa new-model
!
!
dot11 syslog
!
dot11 ssid GTEST
!
dot11 ssid test
!
dot11 ssid test2
!
!
!
username Cisco password 7 047802150C2E
!
!
bridge irb
!
!
interface Dot11Radio0
ip address 10.10.10.100 255.255.255.0
no ip route-cache
!
ssid test
!
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface Dot11Radio1
ip address 10.10.10.101 255.255.255.0
no ip route-cache
!
ssid GTEST
!
ssid test2
!
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface BVI1
ip address 192.168.1.200 255.255.255.0
no ip route-cache
!
ip default-gateway 192.168.1.1
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag 1 route ip
!
!
!
line con 0
line vty 0 4
login local
!
end

bridge

At the moment I dont see anything broadcasting for me to connect to, to gain access to the web gui- I'm sure i screwed the pooch somewhere!

Re: Configuring AIR-WLC4402-50-K9 through CLI

Federico Lovison — Sat, 11 Dec 2010 11:35:39 GMT

Hi Brian,

I would suggest to modify your configuration as follows, so to be able to associate to the open SSID called "test".

Please see the changes I marked in red :

!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
enable secret 5 $1$hDfR$kvTnx/C3JJ0KOqrQzgwuY1
!
no aaa new-model
!
!
dot11 syslog
!
dot11 ssid GTEST
!
dot11 ssid test
    authentication open     # add this
    guest-mode                 # add this
!
dot11 ssid test2
!
!
!
username Cisco password 7 047802150C2E
!
!
bridge irb
!
!
interface Dot11Radio0
ip address 10.10.10.100 255.255.255.0   # remove this
no ip route-cache
!
ssid test
!
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface Dot11Radio1
ip address 10.10.10.101 255.255.255.0    # remove this
no ip route-cache
!
ssid GTEST
!
ssid test2
!
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface BVI1
ip address 192.168.1.200 255.255.255.0    # open the web-gui through this IP address
no ip route-cache
!
ip default-gateway 192.168.1.1
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag 1 route ip
!
!
!
line con 0
line vty 0 4
login local
!
end

I hope this helps.

Regards,

Federico

--
If this answers your question please mark the question as "answered" and rate it, so other users can easily find it.

Re: Configuring AIR-WLC4402-50-K9 through CLI

decrypted08 — Sat, 11 Dec 2010 16:54:23 GMT

How do I remove the IP addresses and

enable the guest and open modes for the radio?

Re: Configuring AIR-WLC4402-50-K9 through CLI

Surendra BG — Sun, 12 Dec 2010 01:12:41 GMT

Hi Brian,

Here is the comand to remove the ip address..

conf t

int dot11 0

no ip address 10.10.10.101 255.255.255.0

end

Regards

Surendra