topic Re: Issue with H-REAP implementation in Wireless

Issue with H-REAP implementation

sumanth_myneni — Sat, 03 Jul 2021 22:14:38 GMT

Hi,

With a 4404 WLC, we tried to implement H-REAP using 1242 AP's. The AP's are continuously rebooting without getting registered to the WLC. Please provide me with the implementation document which is other that Document ID :71250 & WLC configuration guide for 4.0 version.

Re: Issue with H-REAP implementation

Rob Huffman — Mon, 21 Jan 2008 13:29:26 GMT

Hi Sumanth,

Here are some additional references;

Hybrid Remote Edge Access Point (H-REAP) Basic Troubleshooting

http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008081103d.shtml

H-Reap Design and Deployment Guide

http://www.cisco.com/en/US/products/ps6521/products_tech_note09186a0080736123.shtml

H-REAP Modes of Operation Configuration Example

http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00807cc3b8.shtml

Hope this helps!

Rob

Re: Issue with H-REAP implementation

sumanth_myneni — Tue, 22 Jan 2008 11:35:18 GMT

Hi Rob,

Thanks for sending me the links. I actually tried these but i couldn't successed. Could you suggest me why the AP's are continously rebooting? Also, please suggest me any other document.

Re: Issue with H-REAP implementation

jordanperks — Tue, 22 Jan 2008 17:52:38 GMT

Will they register in local mode and then once you set them to H-REAP they start rebooting?

Re: Issue with H-REAP implementation

sumanth_myneni — Wed, 23 Jan 2008 04:32:26 GMT

Yes. When we connect locally, the AP gets registered. At the remote end, the AP continously reboots.

Re: Issue with H-REAP implementation

jordanperks — Wed, 23 Jan 2008 04:54:27 GMT

What I meant was, when your remote APs are in local mode rather than H-REAP mode are they still rebooting? Not physically local, just the mode they are operating in.

Re: Issue with H-REAP implementation

sumanth_myneni — Wed, 23 Jan 2008 05:07:48 GMT

When the AP is in Local mode, the AP gets registered. It doesn't reboot continuously. We have more than 50 AP's working in LOCAL mode without issues.

Re: Issue with H-REAP implementation

jordanperks — Wed, 23 Jan 2008 05:21:01 GMT

So when the AP is in local mode it works fine and the second you use the controller or WCS to put it into H-REAP mode it starts rebooting over and over? Do you have the "enable H-REAP" box on your WLAN checked? I guess I am somewhat at a loss. I have yet to see this happen and I just asked my CCIE Cisco rep today if he has any idea and he couldn't think of anything.

Re: Issue with H-REAP implementation

sumanth_myneni — Wed, 23 Jan 2008 08:02:18 GMT

When the AP connects in local mode, we do not have any issues. If we connect to remote location via H-REAP, the AP doesn't allow me to do any configuration changes and reboots continously. I enabled H-REAP on SSID & in AP details tab too.

Please provide me with the document which can help me.

Re: Issue with H-REAP implementation

sumanth_myneni — Thu, 24 Jan 2008 05:09:30 GMT

Hi,

Please find the error that i observed.

"LWAPP_CLIENT_ERROR_DEBUG: spamHandleJoinTimer: Did not recieve the Join response"

Advice on why this is recurring.

Re: Issue with H-REAP implementation

sumanth_myneni — Mon, 28 Jan 2008 04:52:43 GMT

Can anyone assist me?

Re: Issue with H-REAP implementation

Scott Fella — Fri, 15 Feb 2008 04:13:07 GMT

First of all, did you stage the ap so that the ap has originally joined the controller? If not, then you will have to use dns to resolve cisco-lwapp-controller@yourdomain.com to the management interface ip address. The ap has to join the controller in order for you to configure the ap to h-reap. The ap reboots, because it hasn't joined the WLC.