topic Cisco WLAN LAN in Wireless

Cisco WLAN LAN

Muhammad0 — Mon, 05 Jul 2021 12:45:31 GMT

hi,

i am using cisco wlan controller 5508 and ap2702 and 702 for my network.....all APs are continuously blinking orange green and blue.....what is the problem.?????????????.....and via wireless my network is much slower than LAN connectivity,,,,

Seems like AP are not

Rasika Nayanajith — Tue, 30 Aug 2016 19:24:54 GMT

Seems like AP are not registered to your WLC.

Were these AP working previously ?

Ensure these AP get IP and can reach WLC. You need to have one method (DHCP option 43, DNS, static or broadcast forwarding) configure to let AP know what is the WLC IP.

http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/70333-lap-registration.html

Otherwise WLC managemnt and AP management should be on the same vlan.

HTH

Rasika

*** Pls rate all useful responses ***

i have not configured dhcp

Muhammad0 — Wed, 31 Aug 2016 04:34:37 GMT

i have not configured dhcp option 43....but others configurations are okay...bcoz all of my users are connected through this AP....and can access to internet...but getting slower internet connectivity than my LAN....

and another thing to inform

Muhammad0 — Wed, 31 Aug 2016 04:41:25 GMT

and another thing to inform that i ahve configured dhcp pool in my Router

Check the led status : http:/

mohanak — Wed, 31 Aug 2016 04:44:15 GMT

Check the led status : http://www.cisco.com/c/en/us/td/docs/wireless/access_point/2700/quick/guide/ap2700getstart.html#pgfId-37791

as per ur docs,,,,,,*Access

Muhammad0 — Wed, 31 Aug 2016 06:02:20 GMT

as per ur docs,,,,,,*Access point location command invoked*

but how can i resolve this problem

seems you haven't primed the

yogender singh ranawat — Wed, 31 Aug 2016 12:00:31 GMT

seems you haven't primed the APs, use cisco airprovision App for the same.

how could I do that...plz

Muhammad0 — Wed, 31 Aug 2016 12:13:35 GMT

how could I do that...plz send any docs or a screenshot plz

http://www.cisco.com/c/en/us

yogender singh ranawat — Wed, 31 Aug 2016 12:28:07 GMT

http://www.cisco.com/c/en/us/td/docs/wireless/access_point/ux-ap/guide/uxap-mobapp-g.html

be careful it needs AP reboots downtime required in production environment you just need to do in one AP other will automatically done via NDP.

ok,,,

Muhammad0 — Wed, 31 Aug 2016 15:13:08 GMT

ok,,,

APs are working properly but

Muhammad0 — Wed, 31 Aug 2016 15:19:47 GMT

APs are working properly but Cycling through green, red, and off....which means Discovery/join process in progress,,,,,how can i solve this problem????

APs are working properly but

Muhammad0 — Wed, 31 Aug 2016 15:20:34 GMT

APs are working properly but Cycling through green, red, and off....which means Discovery/join process in progress,,,,,how can i solve this problem????

Console into one of those APs

Rasika Nayanajith — Wed, 31 Aug 2016 19:33:05 GMT

Console into one of those APs and attach output while it is going through this process.

Also get the output of "show version" from the AP and "show sysinfo" from your WLC CLI

HTH

Rasika

Have these AP's ever worked

pwwiddicombe — Sat, 10 Sep 2016 02:33:39 GMT

Have these AP's ever worked properly, or have they always done this?

I have had a few 3602's that periodically (i.e. every few months) needed a hard reset (just pull the ethernet cable they are attached to out of the switch for 20 seconds or so).

RMA'd them eventually, and the problem went away.

Are you saying the ap's are

Scott Fella — Sun, 11 Sep 2016 02:40:23 GMT

Are you saying the ap's are working fine, but the LED is cycling through the various colors? Maybe you have the blink LED configured somehow? Maybe try this command:

config ap led-state flash disable <Cisco AP>

-Scott

*** Please rate helpful posts ***