topic with WGB and multiple vlans in Wireless

Universal Workgroup Bridge & IP Broadcasts

rshade-cti — Mon, 05 Jul 2021 10:24:10 GMT

I'm attempting to configure the integrated AP in the C819 as a bridge. I can't rely on the infrastructure to be Cisco, so I'm using "station-role workgroup-bridge universal" with the MAC of the router. For some reason, the bridge AP is not accepting/forwarding broadcast traffic from the infrastructure. Broadcast packets (DHCP/ARP) egress the bridge AP (I can see them on the infrastructure side), but the replies never make it through the bridge AP. I blame the bridge AP because other clients can ARP/DHCP just fine w/the infrastructure. Unicast packets from the infrastructure are forwarded correctly.

We currently have a few hundred 3200 MARs using this exact technique and they don't have trouble with broadcasts.

Any idea what I could be missing?

with WGB and multiple vlans

ali aqrabawi — Sun, 14 Jun 2015 17:49:09 GMT

with WGB and multiple vlans two things should be configured :

1) add the command "infra-structure SSID" , under the WGB SSID .

2)the WGB SSID should be in native vlan which is 12 , i see its configured for 11 and 11 is tagged vlan.

correct these two things and it should work ,

Thanks for looking at it, Ali

rshade-cti — Mon, 15 Jun 2015 16:02:47 GMT

Thanks for looking at it, Ali.

Unfortunately, I'm still seeing the same behavior that suggestion. My current config is attached.

yes the configuration now is

ali aqrabawi — Mon, 15 Jun 2015 19:21:19 GMT

yes the configuration now is correct ,

is it working now ?

No. The router is still not

rshade-cti — Mon, 15 Jun 2015 19:22:34 GMT

No. The router is still not receiving any of the broadcast packets from the wireless.

can you share the show run

ali aqrabawi — Mon, 15 Jun 2015 19:41:31 GMT

can you share the show run from the root AP ?

is it cisco or non-cisco AP ?

collect show brdige and show arp from the WGB .

and show run from 3200 mobility router

do you see the DHCP packet going out the wired/wireless clients behind the WGB , but no reply from the other side ? or you are checking from the root AP side ,

if you connect a wired client behind the bridge to vlan 20 , does it take ip address ?

Sorry for the delay. Thanks

rshade-cti — Wed, 17 Jun 2015 16:10:42 GMT

Sorry for the delay. Thanks again for looking at this.

can you share the show run from the root AP ?

> attached

is it cisco or non-cisco AP ?

> Cisco, for testing purposes

collect show brdige and show arp from the WGB .

vehicle-router-ap#show bridge

Total of 300 station blocks, 299 free
Codes: P - permanent, S - self

Bridge Group 1:

Address Action Interface Age RX count TX count
6cfa.89d5.84a2 forward Gi0.11 0 5 0
vehicle-router-ap#show arp

vehicle-router-ap#

and show run from 3200 mobility router

> That's a bit tough due to all the customer specific data. Here are some relevant snippets:

dot11 ssid (redacted)
vlan 11
authentication open eap eap_methods1
authentication network-eap eap_methods1
authentication key-management wpa
accounting acct_methods1
dot1x credentials TLS
encryption mode ciphers tkip
!

bridge irb
!
!
interface Dot11Radio0
no ip address
no ip route-cache
!
ssid (redacted)
!
antenna transmit right-a
antenna receive right-a
station-role workgroup-bridge universal 1cdf.0fcc.7052
rts threshold 4000
no cdp enable
infrastructure-client
!
interface Dot11Radio0.11
encapsulation dot1Q 11 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
!
interface FastEthernet0
no ip address
no ip route-cache
speed auto
full-duplex
!
interface FastEthernet0.11
description IP address here needed to support SNMP signaling to MARC
encapsulation dot1Q 11 native
ip address 10.255.253.251 255.255.255.0
no ip route-cache
bridge-group 1
!
interface FastEthernet0.20
description Sub-interface for consistent access/administration whether inside or outside of 802.11 coverage
encapsulation dot1Q 20
ip address 10.255.255.251 255.255.255.0
no ip route-cache
bridge-group 20
!
interface BVI1
description Bridge Virtual Address - On Vlan11 from MARC's perspective
ip address 10.255.254.251 255.255.255.0
no ip route-cache
!
ip default-gateway 10.255.255.254
no ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

bridge 1 route ip
bridge 1 aging-time 120
bridge 20 aging-time 86400

do you see the DHCP packet going out the wired/wireless clients behind the WGB , but no reply from the other side ? or you are checking from the root AP side ,

> I have a monitor session on the switchport the root AP is connected to

> I see the broadcasted DISCOVER from the WGB and a broadcasted OFFER. There's no indication in the router receives it (based on the output from debug dhcp)

if you connect a wired client behind the bridge to vlan 20 , does it take ip address ?

> yes. Other clients (laptops/iPhones) also work when connecting to the root AP

on the AP of the 3200 add

ali aqrabawi — Wed, 17 Jun 2015 16:25:17 GMT

on the AP of the 3200 add this subinterface :

interface Dot11Radio0.20

encapsulation dot1q 20

bridge-group 20

----------------------------------------

on the root AP, you can copy and paste :

add below :

interface Dot11Radio0.20

encapsulation dot1q 20

bridge-group 20

interface Dot11Radio0.11

encapsulation dot1q 11 native

bridge-group 1

interface FastEthernet0.20

encapsulation dot1q 20

bridge-group 20

interface FastEthernet0.11

encapsulation dot1q 11 native

bridge-group 1

dot11 ssid iotwifi

vlan 11

===========

it should work ,

if not collect show bridge again from both sides .