topic Hello All i need help i want in Wireless

Cisco-5508 WLC

thusharadennis — Mon, 05 Jul 2021 09:02:28 GMT

Dear Team,

I am configuring a controller in Portugal and the Model of the AP in the particular location is AIR-CAP3702E-A-K9 from google I understood that the country code is of Canada . So i tried enabling two Country code in the WLC but after that also the AP ia not registering with the controller.

Also checked in the switch end , AP is getting IP address and the controller IP is reachable from the Switch.

Kindly provide clarification on the same.

Device ID: APf40f.1bd1.a84c
Entry address(es):
IP address: 10.197.91.3
Platform: cisco AIR-CAP3702E-A-K9, Capabilities: Router Trans-Bridge
Interface: FastEthernet0/47, Port ID (outgoing port): GigabitEthernet0.1
Holdtime : 175 sec

Version :
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.2(4)JB6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 22-Aug-14 11:52 by prod_rel_team

advertisement version: 2
Duplex: full
Power drawn: 15.400 Watts
Power request id: 22470, Power management id: 3
Power request levels are:16800 15400 13000 0 0
Management address(es):

Regards

Thushara

Hi Thushara,Here is the Cisco

Rasika Nayanajith — Mon, 01 Dec 2014 21:39:48 GMT

Hi Thushara,

Here is the Cisco AP regulatory domain reference document

http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1300-series/product_data_sheet0900aecd80537b6a.html

It is not recommended to configure countries in two different regulatory domain on the same WLC. Then WLC has to work out common channel & power level applicable to both these domain & due to this sometimes radios get disabled.

In your case, you have to get the correct regulatory domain AP to install in Portugal as regulatory requirement is different in EMEA region that to the North America.

HTH

Rasika

**** Pls rate all useful responses ****

Post the WLC output to the

Leo Laohoo — Mon, 01 Dec 2014 21:42:32 GMT

Post the WLC output to the command "sh sysinfo".

Dear Team i nee to implement

Assadullah — Sun, 07 Dec 2014 07:25:53 GMT

Dear Team

i nee to implement the IPv6 on my cisco wireless controller with version 5508 image version 7.6.110.0 with ap 1262 and 1252

Regards

Assad

Hi Assad,If you want to

Rasika Nayanajith — Sun, 07 Dec 2014 08:01:17 GMT

Hi Assad,

If you want to implement IPv6, then best WLC code is 8.x. I would suggest you to wait for 8.0MR1 code to be released & then move on to that. Here is the IPv6 deployment guide of that code

http://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/8-0/IPV6_DG.html

Here is the link if you want to get pre-release of 8.0MR1

https://supportforums.cisco.com/document/12298741/80-mr1-beta-availability

HTH

Rasika

*** Pls rate all useful responses ****

Dear Manannalage Thanks iam

Assadullah — Sun, 07 Dec 2014 09:59:59 GMT

Dear Manannalage

Thanks iam using wireless controller 5508 with ios version 7.6.110.0 with access point 1262 and 1252 how i can configured IPv6 in the mention Aps

Need your cooperation

Regards

Assad

Hi Assad,Pls explain your

Rasika Nayanajith — Sun, 07 Dec 2014 10:24:06 GMT

Hi Assad,

Pls explain your requirement in detail. Also mention the IPv6 scheme need to be used in your solution.

Rasika

Dear ManannalageThanks too

Assadullah — Sun, 07 Dec 2014 10:35:57 GMT

Dear Manannalage

Thanks too much for your help for the first time just i want to know how i can configured IPv6 in my wireless controller model 5508 IOS 7.6.110.0 this wlc is supporting 500 ap

iam using Cisco access point 1260 AIR-LAP1262N-N-K9

I need your support if possible some videos it will understandable for me

HiCheck below link as it

Rasika Nayanajith — Sun, 07 Dec 2014 10:41:38 GMT

Check below link as it gives very basic idea on how to configure it on 7.0.x code.

https://www.youtube.com/watch?v=94vGOhkXr0s

https://supportforums.cisco.com/document/71146/ipv6-support-cisco-wlc-wireless-lan-controller-configuring-ipv6-bridging

As I said earlier, 8.x is the code which added native IPv6 support on these WLC. So if you really want IPv6 that is the code to be.

Pls rate all useful responses (2 star rating is not that encouraging :))

HTH

Rasika

Hello Manannalagethanks for

Assadullah — Mon, 08 Dec 2014 06:53:58 GMT

Hello Manannalage

thanks for your support i hear IPv6 is not work with lightweight access point

Regards

Assad

thanks for your support i

Rasika Nayanajith — Mon, 08 Dec 2014 23:58:11 GMT

thanks for your support i hear IPv6 is not work with lightweight access point

From where you hear that message, all the links I Provided talks about IPv6 in Lightweight (or WLC managed) AP deployments.

HTH

Rasika

Hello Dear Manannalagecan you

Assadullah — Wed, 10 Dec 2014 05:05:36 GMT

Hello Dear Manannalage

can you help me how to up garde my lightweight access 1260 vs with wlc 5508

Regards

Assad

Hi Assad,You simply need to

Rasika Nayanajith — Wed, 10 Dec 2014 05:16:41 GMT

Hi Assad,

You simply need to upgrade your 5508 controller software & then AP will automatically upgraded by getting the image from your WLC.

Read the release notes of the version you going for

http://www.cisco.com/c/en/us/support/wireless/5500-series-wireless-controllers/products-release-notes-list.html

Also make sure your WLC FUS upgraded to latest 1.9.0.0 as well. This will take around 30-40min & prefer if you can do it via console.

http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/fus_rn_OL-31390-01.html

HTH

Rasika

*** Pls rate all useful response ***

Hi Mr.ManannalageI have up

Assadullah — Wed, 10 Dec 2014 05:42:51 GMT

Hi Mr.Manannalage

I have up garde my wireless controller from 7.0.116.0 to 7.6.110.0 still some of my access 11/n is not support it it means it is not change the ap ios

Regards

Assad

Pls provide "show sysinfo"

Rasika Nayanajith — Wed, 10 Dec 2014 09:10:06 GMT

Pls provide "show sysinfo" output from your WLC

Rasika

Dear ManannalageThis is the

Assadullah — Wed, 10 Dec 2014 09:14:05 GMT

Dear Manannalage

This is the sysinfor

(Cisco Controller) >show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.110.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS

System Name...................................... TEST
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 172.30.221.232
Last Reset....................................... Software reset
System Up Time................................... 8 days 22 hrs 27 mins 39 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180

Configured Country............................... Multiple Countries:KE,US
Operating Environment............................ Commercial (0 to 40 C)

--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +33 C
External Temperature............................. +19 C
Fan Status....................................... OK

State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 7
Number of Active Clients......................... 0

Burned-in MAC Address............................ 50:57:A8:BB:EC:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 250

Your WLC 802.11a network is

Rasika Nayanajith — Wed, 10 Dec 2014 19:09:17 GMT

Your WLC 802.11a network is globally disabled. Try to enable it & see

(2504-1) >config 802.11a enable network

You can verify using this

(2504-1) >show 802.11a

If you cannot enable, that may be due to multiple country configured in different regulatory domains

Configured Country............................... Multiple Countries:KE,US

In which country AP is in ? Check your 1262 AP & make sure it belong to correct regulatory domain (show version of the AP provide this info)

http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1300-series/product_data_sheet0900aecd80537b6a.html#Table280211abgnControllerBasedAcc

HTH

Rasika

**** Pls rate all useful responses ****

Hello Mannanalage Thanks for

Assadullah — Wed, 07 Jan 2015 05:32:48 GMT

Hello Mannanalage

Thanks for always support i need your help how i can take my wireless lan controller 5508 ios back up

and next i want to up garde my Cisco access point 1262 ios lightweight

Regards

Assad

You should upgrade to v7.6

Scott Fella — Wed, 07 Jan 2015 12:33:27 GMT

You should upgrade to v7.6.130.0 as that image your in isn't stable. Also you didn't upgrade your FUS to 1.9.0.0 like Rasika mentioned. If your talking about backed my up the configurations, you can look at the WLC configuration guide as it will explain how to perform that. There is no need to backup the WLC image as you can always download that again. Access points gets upgraded when the join the WLC. If you have autonomous AP's, then search Google for:

Cisco autonomous to lightweight conversion

Yiu will find many ways to do this along with YouTube videos. You can also search the forum for specifics if you run into issues.

-Scott

Hello All i need help i want

Assadullah — Tue, 13 Jan 2015 07:23:52 GMT

Hello All

i need help i want to for users make a username and password when users want to connect in wireless asking for username and password iam wlc 5508 with ap 1262

Regards

Assad