topic data rate configurations in Wireless

data rate configurations

saleh.iskandar — Sun, 04 Jul 2021 07:25:51 GMT

Dear All,

in cisco WLC,

can we disable certain data rate for specific WLAN/SSID instead of using global paramaters ???

(Wireless > 802.11a/n or 802.11b/g/n > Network to open the 802.11a (or 802.11b/g) Global Parameters page)

Re: data rate configurations

George Stefanick — Tue, 16 Jul 2013 02:20:54 GMT

No sorry .. Global only ..

Sent from Cisco Technical Support iPad App

Re: data rate configurations

Leo Laohoo — Tue, 16 Jul 2013 02:38:47 GMT

can we disable certain data rate for specific WLAN/SSID  instead of using global paramaters ???

Yes you can. If you enable RF Profile. Wireless > RF Profile

NOTE: Not available in all codes. I believe it's supported in 7.3.X and up.

Re: data rate configurations

saleh.iskandar — Tue, 16 Jul 2013 02:41:34 GMT

When we apply rf profile , does it means we associate the rf profile to AP groups ?

Therefore I think, it is per AP level (affecting all WLAN inside) not per WLAN/SSID.

data rate configurations

Leo Laohoo — Tue, 16 Jul 2013 02:44:44 GMT

When we apply rf profile , does it means we associate the rf profile to AP groups ?

Yes.

Therefore I think, it is per AP level (affecting all WLAN inside)  not per WLAN/SSID.

No. It's SSID-level too. You put your APs in an AP Group, attach the RF Profile in.

Re: data rate configurations

George Stefanick — Tue, 16 Jul 2013 02:48:30 GMT

I just got schooled !

+5 Leo

Sent from Cisco Technical Support iPad App

Re: data rate configurations

Scott Fella — Tue, 16 Jul 2013 02:50:02 GMT

Haha

Sent from Cisco Technical Support iPhone App

data rate configurations

Leo Laohoo — Tue, 16 Jul 2013 03:17:48 GMT

Thanks for the ratings, George.

Re: data rate configurations

Scott Irey — Wed, 17 Jul 2013 00:53:49 GMT

Rf profiles made their debut in 7.2

Sent from Cisco Technical Support iPhone App

Re: data rate configurations

Saurav Lodh — Wed, 17 Jul 2013 04:23:04 GMT

To define the data rates on a per-SSID basis, do the following:

Define the average data rate TCP traffic per SSID by entering the rate in Kbps in the Average Data Rate text boxes. A value of 0 indicates that the value specified in the selected QoS profile will take effect.
Define the peak data rate for TCP traffic per SSID by entering the rate in Kbps in the Burst Data Rate text boxes. A value of 0 indicates that the value specified in the selected QoS profile will take effect.
Note
The burst data rate should be greater than or equal to the average data rate. Otherwise, the QoS policy may block traffic in the WLANs.
Define the average real-time rate for UDP traffic per SSID by entering the rate in Kbps in the Average Real-Time Rate text boxes. A value of 0 indicates that the value specified in the selected QoS profile will take effect.
Define the peak real-time rate for UDP traffic per SSID by entering the rate in Kbps in the Burst Real-Time Rate text boxes. A value of 0 indicates that the value specified in the selected QoS profile will take effect.
Note
The burst real-time rate should be greater than or equal to the average real-time rate. Otherwise, the QoS policy may block traffic in the WLANs.

Please refer the below link ( Qos )

http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/consolidated/b_cg74_CONSOLIDATED_chapter_01010111.html

Re: data rate configurations

George Stefanick — Wed, 17 Jul 2013 16:01:28 GMT

I think he was asking for PHY rates not thoughtput .. And btw RF profile is based around AP not SSID.

__________________________________________________________________________________________
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
__________________________________________________________________________________________
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

Re: data rate configurations

saleh.iskandar — Wed, 17 Jul 2013 16:16:26 GMT

george is right

I am asking for PHY rate

And also I agree with george, RF profile is around AP not SSID.

Well, FYI, I experienced with Aruba in the past, and Aruba Mobility Controller can do rate configurations around

virtual AP/SSID (not per AP level).

thanks all !.

regards

Saleh Iskandar

Re: data rate configurations

George Stefanick — Wed, 17 Jul 2013 16:22:51 GMT

Which leads me back to my original comment , it's not supported .. Lol

Sent from Cisco Technical Support iPhone App