topic Re: Error downloading image from 5508 to 3602 in Wireless

Error downloading image from 5508 to 3602

matthew.coffin — Sun, 04 Jul 2021 05:27:45 GMT

Here is the full rundown of the bootup and (attempted image load from the lap):

IOS Bootloader - Starting system.

flash is writable

FLASH CHIP: Numonyx Mirrorbit (0089)

Xmodem file system is available.

flashfs[0]: 4 files, 3 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 31997952

flashfs[0]: Bytes used: 3364864

flashfs[0]: Bytes available: 28633088

flashfs[0]: flashfs fsck took 12 seconds.

Reading cookie from SEEPROM

Base Ethernet MAC address: a4:93:4c:c1:1d:5c

Ethernet speed is 1000 Mb - FULL Duplex

Loading "flash:/ap3g2-rcvk9w8-mx.124-23c.JY/ap3g2-rcvk9w8-mx.124-23c.JY"...###################################################################################################################################################################

File "flash:/ap3g2-rcvk9w8-mx.124-23c.JY/ap3g2-rcvk9w8-mx.124-23c.JY" uncompressed and installed, entry point: 0x2003000

executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

Rights clause at FAR sec. 52.227-19 and subparagraph

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, C3600 Software (AP3G2-RCVK9W8-M), Version 12.4(23c)JY, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Wed 26-Oct-11 19:21 by prod_rel_team

Proceeding with system init

Proceeding to unmask interrupts

Initializing flashfs...

FLASH CHIP: Numonyx Mirrorbit (0089)

flashfs[1]: 4 files, 3 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 31739904

flashfs[1]: Bytes used: 3364864

flashfs[1]: Bytes available: 28375040

flashfs[1]: flashfs fsck took 7 seconds.

flashfs[1]: Initialization complete.

flashfs[2]: 0 files, 1 directories

flashfs[2]: 0 orphaned files, 0 orphaned directories

flashfs[2]: Total bytes: 11999232

flashfs[2]: Bytes used: 1024

flashfs[2]: Bytes available: 11998208

flashfs[2]: flashfs fsck took 0 seconds.

flashfs[2]: Initialization complete....done Initializing flashfs.

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

%Error opening flash:/ap3g2-rcvk9w8-mx/info (No such file or directory)cisco AIR-CAP3602I-A-K9 (PowerPC) processor (revision B0) with 167926K/81920K bytes of memory.

Processor board ID FTX1625GNE8

PowerPC CPU at 800Mhz, revision number 0x2151

Last reset from power-on

LWAPP image version 7.0.114.214

1 Gigabit Ethernet interface

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: A4:93:4C:C1:1D:5C

Part Number : 73-14521-01

PCA Assembly Number : 800-37501-01

PCA Revision Number : A0

PCB Serial Number : FOC16223RVZ

Top Assembly Part Number : 800-35852-02

Top Assembly Serial Number : FTX1625GNE8

Top Revision Number : A0

Product/Model Number : AIR-CAP3602I-A-K9

% Please define a domain-name first.

logging facility kern

% Invalid input detected at '^' marker.

Press RETURN to get started!

*Mar 1 00:00:09.311: %LWAPP-3-CLIENTEVENTLOG: Unable to open event log file flash:/event.log

*Mar 1 00:00:09.311: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 0 messages)

*Mar 1 00:00:11.235: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up

*Mar 1 00:00:11.251: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C3600 Software (AP3G2-RCVK9W8-M), Version 12.4(23c)JY, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyrig

Compiled Wed 26-Oct-11 19:21 by prod_rel_team

*Jun 11 00:27:35.027: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Jun 11 00:27:35.979: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to downDPAA Initialization Complete

*Jun 11 00:27:37.627: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited

*Jun 11 00:27:38.627: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up

*Jun 11 00:27:48.251: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 192.168.0.233, mask 255.255.255.0, hostname APa493.4cc1.1d5c

*Jun 11 00:27:57.451: %CDP_PD-2-POWER_LOW: All radios disabled - INJECTOR_DETECTED_PD AIR-CAP3602E-A-K9 (0000.0000.0000)

Translating "CISCO-CAPWAP-CONTROLLER"...domain server (192.168.0.1)

Translating "CISCO-LWAPP-CONTROLLER"...domain server (192.168.0.1)

*Jul 26 18:12:02.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.0.2 peer_port: 5246

*Jul 26 18:12:02.999: %CAPWAP-5-CHANGED: CAPWAP changed state to

*Jul 26 18:12:03.499: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.0.2 peer_port: 5246

*Jul 26 18:12:03.499: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.0.2

*Jul 26 18:12:03.499: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

examining image...

*Jul 26 18:12:08.499: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.0.2perform archive download capwap:/ap3g2 tar file

*Jul 26 18:12:08.511: %CAPWAP-6-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.

*Jul 26 18:12:08.515: %CAPWAP-5-CHANGED: CAPWAP changed state to IMAGE

*Jul 26 18:12:08.515: Loading file /ap3g2...

logging facility kern

% Invalid input detected at '^' marker.

%Error opening flash:/update/info (No such file or directory)

ERROR: Image is not a valid IOS image archive.

archive download: takes 48 seconds

*Jul 26 18:12:56.567: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.0.2:5246

*Jul 26 18:12:56.567: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Jul 26 18:12:56.627: %CAPWAP-3-ERRORLOG: capwap ifs: read error or timeout

*Jul 26 18:12:56.635: capwap_image_proc: problem extracting tar file

*Jul 26 18:13:06.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.0.2 peer_port: 5246

*Jul 26 18:13:06.000: %CAPWAP-5-CHANGED: CAPWAP changed state to

*Jul 26 18:13:06.495: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.0.2 peer_port: 5246

*Jul 26 18:13:06.499: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.0.2

*Jul 26 18:13:06.499: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN

This is from the logs on the wlc:

*spamApTask7: Jul 26 14:32:11.044: %CAPWAP-3-TX_ERR: capwap_ac_sm.c:4172 The system has failed to transmit image data request to AP 2c:54:2d:9c:a1:f9

*spamApTask7: Jul 26 14:32:11.044: %CAPWAP-3-ENCODE_ERR: capwap_ac_sm.c:2425 The system has failed to encode Image data request to AP 2c:54:2d:9c:a1:f9

*spamApTask7: Jul 26 14:32:11.044: %CAPWAP-3-IMAGE_DOWNLOAD_ERR3: capwap_ac_platform.c:782 Refusing image download request from AP - unable to open image file /bsn/ap//ap3g2

Any ideas?

I have so far:

Tried mac filtering for this particular ap, as well as two others.

verified auth vs mic was enabled with appropriate mac entered, and removed it as well.

The wlc is set as the master.

Error downloading image from 5508 to 3602

matthew.coffin — Thu, 26 Jul 2012 18:39:40 GMT

Additionally:

The error under stats is:

Last Error Occurred Reason Timed out while waiting for ECHO repsonse from the AP

Error downloading image from 5508 to 3602

Stephen Rodriguez — Thu, 26 Jul 2012 18:42:14 GMT

What version of code are you running on the WLC?

Can you capture the output of the following debugs while the AP is trying to join?

debug mac-address a4:93:4c:c1:1d:5c

debug capwap events enable

debug capwap errors enable

HTH,
Steve

-----------------------------------------
Please remember to rate useful posts, and mark questions as answered

Re: Error downloading image from 5508 to 3602

matthew.coffin — Thu, 26 Jul 2012 18:55:33 GMT

Running version

7.2.103.0

Debug logs:

(Cisco Controller) >debug

(Cisco Controller) debug>capwap events enable

spamApTask0: Jul 26 14:51:37.420: a4:93:4c:c1:1d:5c Failed to parse CAPWAP packet from 192.168.0.233:4567

*spamApTask7: Jul 26 14:52:14.494: 2c:54:2d:9c:a1:f9 DTLS connection not found, creating new connection for 192:168:0:222 (51745) 192:168:0:2 (5246)

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCID: called to evaluate

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCID: comparing to row 0, CA cert >bsnOldDefaultCaCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCID: comparing to row 1, CA cert >bsnDefaultRootCaCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCID: comparing to row 2, CA cert >bsnDefaultCaCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCID: comparing to row 3, CA cert >bsnDefaultBuildCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCID: comparing to row 4, CA cert >cscoDefaultNewRootCaCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCID: comparing to row 5, CA cert >cscoDefaultMfgCaCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCID: comparing to row 0, ID cert >bsnOldDefaultIdCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCID: comparing to row 1, ID cert >bsnDefaultIdCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCID: comparing to row 2, ID cert >cscoDefaultIdCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCertFromCID: called to get cert for CID 13244df5

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultCaCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultRootCaCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCertFromCID: comparing to row 2, certname >bsnDefaultCaCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCertFromCID: comparing to row 3, certname >bsnDefaultBuildCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCertFromCID: comparing to row 4, certname >cscoDefaultNewRootCaCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCertFromCID: comparing to row 5, certname >cscoDefaultMfgCaCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCertFromCID: comparing to row 0, certname >bsnOldDefaultIdCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCertFromCID: comparing to row 1, certname >bsnDefaultIdCert<

*spamApTask7: Jul 26 14:52:14.494: sshpmGetCertFromCID: comparing to row 2, certname >cscoDefaultIdCert<