topic Template that fails on deployment in Wireless

Template that fails on deployment

Philip Vilhelmsson — Sun, 04 Jul 2021 03:52:51 GMT

Hi,

I am trying to deploy a template to our AIR-LAP1242AG-E-K9 (12.4(23c)JA2) in WCS. What the template is doing is enabling VLAN support for HREAP.

The AP parameters enabled in the template are:

AP Mode: HREAP/REAP

HREAP/REAP configuration: our WLANs

VLAN Support Enable with our Native VLAN

But when I try to deploy it I get: Partial Success. **AP Parameters** HREAP: Profile NAME-VLAN Id mappings cannot be applied since VLAN Support status is disabled on the template.

When I check the AP after that VLAN isn't enabled under HREAP configuration.

Any Ideas?

/Ph

Re: Template that fails on deployment

Kayle Miller — Fri, 07 Oct 2011 14:08:34 GMT

Philip,

I have had issues in the past with this as well, and I have never found a solution to pushing out H-REAP configs to the AP's so I created scripts that did it from the CLI. It makes it fairly easy and quick.

The reason it doesn't seem to work is because it doesn't appear to tick the enable vlans check box; but one thing you may try since I know you have to do it from the CLI is try disabling the AP's first then push out the template and see what happens.

Sorry I can't provide more insight.

HTH

Template that fails on deployment

Stephen Rodriguez — Fri, 07 Oct 2011 14:31:35 GMT

To get around this, you'll want to have one template that enables HREAP, then reboots the AP. A second template would then set the WLAN/VLAN mappings.

HTH,
Steve

----------------------------------------------------------------------------------------------------------

Please remember to rate helpful posts or to mark the quesiton as answered so that it can be found later.

Template that fails on deployment

Mirza Cutuk — Fri, 23 Dec 2011 13:26:34 GMT

It is an old thread, but i am experiencing this problem even with multiple templates. One for h-reap enable, one for vlan config.

Re: Template that fails on deployment

Stephen Rodriguez — Fri, 23 Dec 2011 13:29:08 GMT

and you are rebooting the ap after you enable VLAN support?

Sent from Cisco Technical Support iPad App

Template that fails on deployment

Kayle Miller — Fri, 23 Dec 2011 14:01:34 GMT

That's why with H-REAP configurations I have built CLI scripts that make it quick and super easy.

Template that fails on deployment

Mirza Cutuk — Fri, 23 Dec 2011 18:46:27 GMT

Hi Stephen.

The template has the reboot option clicked in. The aps i used to stage before used to reboot after i applied the template. But not anymore.

@Kayle Miller

Do share here or send them to mali.zeleni[at]gmail

Re: Template that fails on deployment

Scott Fella — Fri, 23 Dec 2011 18:57:06 GMT

I think you have to disable the admin status first then execute your templates then enable the admin status.

I too use the CLI for almost everything. If you run through the CLI and figure out what commands you need, you can create a custom CLI template and use that.

Thanks,

Scott Fella

Sent from my iPhone

Template that fails on deployment

s.clinard — Wed, 27 Jun 2012 14:28:11 GMT

Hi Philip -

I know this post is old but I just referenced it to see if it would solve the same issue for me. I figured it out -

When you are congfiguring the AP template, enable H-REAP/REAP configuration, and enable VLAN support with the proper VLAN for your environment. Then apply the template to your APs. Once VLAN support is enabled and applied, go back to your AP template, click Show All Profile-Mapping, select your WLAN, and set the proper VLAN for your environment. Then apply the template to your APs again.

HTH,

Shane

This is my Excel Workbook to

Kayle Miller — Tue, 13 May 2014 20:15:51 GMT

This is my Excel Workbook to do all the H-REAP Commands from CLI, the FlexConnect Commands are different.

Just paste in the AP information on the tabs and fill out the other yellow fields then you have you command syntax populated in the other tabs.

one of the Tabs requires you to paste into wordpad or a text editor and remove the " from the lines. but the others you can just cut and paste.

Re: This is my Excel Workbook to

ray.holtz — Tue, 27 Aug 2019 19:19:22 GMT

5 years later, and this spreadsheet is still helping! I just found it! Thanks Kayle!