Web interface not work

remosa2010 — Sun, 04 Jul 2021 02:01:45 GMT

Good morning, i've purchased an AP LAP 1131AG, i need to access in web interface but this not work.

i've configured static ip means console port, i ping that ip , but when i try to access in web interface this not work.

this is my startup:

Reset done!

ethernet link up, 100 mbps, full-duplex

Ethernet port 0 initialized: link is up

Loading "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"...###########################

################################################################################

##############################################################

File "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx" uncompressed and installed, entr

y point: 0x3000

executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

Rights clause at FAR sec. 52.227-19 and subparagraph

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEA

SE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Mon 17-Jul-06 11:38 by alnguyen

Image text-base: 0x00003000, data-base: 0x0035E440

Initializing flashfs...

flashfs[1]: 4 files, 2 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 15998976

flashfs[1]: Bytes used: 1870848

flashfs[1]: Bytes available: 14128128

flashfs[1]: flashfs fsck took 4 seconds.

flashfs[1]: Initialization complete....done Initializing flashfs.

cisco AIR-LAP1131AG-E-K9 (PowerPCElvis) processor (revision B0) with 24566K/81

92K bytes of memory.

Processor board ID FCZ1407Q1SD

PowerPCElvis CPU at 262Mhz, revision number 0x0950

Last reset from power-on

LWAPP image version 3.0.51.0

1 FastEthernet interface

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 88:43:E1:AA:1A:E4

Part Number : 73-8962-14

PCA Assembly Number : 800-24818-13

PCA Revision Number : A0

PCB Serial Number : FOC140453YY

Top Assembly Part Number : 800-29144-03

Top Assembly Serial Number : FCZ1407Q1SD

Top Revision Number : A0

Product/Model Number : AIR-LAP1131AG-E-K9

Press RETURN to get started!

*Mar 1 00:00:06.307: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power s

ource

*Mar 1 00:00:06.313: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEA

SE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Mon 17-Jul-06 11:38 by alnguyen

*Mar 1 00:00:07.267: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to

*Mar 1 00:00:08.267: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthern

et0, changed state to up

Re: Web interface not work

dancampb — Thu, 29 Jul 2010 13:05:42 GMT

That AP is running a lightweigh image and doesn't have a web interface. Are you planning on using this AP with a controller or as an autonomous AP? If you want to use it as an autonomous AP you need to convert it:

http://www.cisco.com/en/US/docs/wireless/controller/6.0/configuration/guide/c60lwap.html#wp1105215

Re: Web interface not work

remosa2010 — Thu, 29 Jul 2010 13:22:56 GMT

I need autonomous AP, for convert Ap i need the access point image file.

I can't download it from download area

Re: Web interface not work

dancampb — Thu, 29 Jul 2010 13:47:48 GMT

You can use any of the autonomous IOS AP images to convert the AP.

Re: Web interface not work

remosa2010 — Thu, 29 Jul 2010 13:54:12 GMT

where can i find autonomous IOS AP images ?

topic Re: Web interface not work in Wireless

Web interface not work

Re: Web interface not work

Re: Web interface not work

Re: Web interface not work

Re: Web interface not work