topic 1310 bridge setting in Wireless

1310 bridge setting

nivanak — Sun, 04 Jul 2021 17:12:58 GMT

hi!

i configuried 1310 , but it is strangely.

if between root and not-root is 9km,it is failed.

appending my configuring. is it right ?

1. 1310 (root)

interface Dot11Radio0

no ip address

no ip route-cache

ssid tsunami

authentication open

guest-mode

infrastructure-ssid

cca 0

concatenation

distance 20

speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0

54.0

rts threshold 4000

power local cck 100

station-role root

infrastructure-client

bridge-group 1

bridge-group 1 spanning-disabled

2.non-root 1310

interface Dot11Radio0

no ip address

no ip route-cache

ssid tsunami

authentication open

guest-mode

infrastructure-ssid

cca 0

concatenation

speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0

54.0

rts threshold 4000

power local cck 100

station-role non-root

mobile station

infrastructure-client

bridge-group 1

bridge-group 1 spanning-disabled

Re: 1310 bridge setting

thisisshanky — Tue, 30 Nov 2004 18:03:22 GMT

What IOS is it ? Try upgrading to 12.3.2 JA and see if it resolves the problem.

If a lower version than 12.3.2.JA, Try changing Cca parameter to 60 and see if it helps!

command is "cca 60"\

http://www.cisco.com/en/US/products/hw/wireless/ps5279/prod_release_note09186a00802146c0.html

Re: 1310 bridge setting

nivanak — Wed, 01 Dec 2004 04:29:15 GMT

and 1310 bridge's LED COLOR is strange.

now, only R , S , E LED are blinking(green).

Install LED is not blinking.(no color).

of course, 2 bridges are same actual condition.

help me.

Re: 1310 bridge setting

thisisshanky — Wed, 01 Dec 2004 06:05:31 GMT

Thats normal. R, S, E LEDs blink at different rates depending on the signal strength. Check this chart for blink rates and signal strengths.

http://www.cisco.com/en/US/products/ps5861/products_installation_guide_chapter09186a008021e5ee.html#wp1042233

Re: 1310 bridge setting

nivanak — Thu, 02 Dec 2004 06:24:31 GMT

thank to your answer.

but i have a question.

now install mode is off. 2 bridges are off.

another R,S,E LED is no problem.

after setting bridge with two 1310 , istall LED is off now.it is strangely.

by your link site,off signal(install LED) is startup.

if install LED of root bridge is green , is it right ?

i do not understand.

Re: 1310 bridge setting

sorvarit — Mon, 06 Dec 2004 15:59:17 GMT

Try to set the mac address (radio interface) to the root parent under in the webinterface on the non root bridge (Network interfaces> Radio0-802.11g> Settings). Solved our problems with the BR1310. Couldnt find eachother 5m away before doing this... They are 4km away so it could be something with distance in your case also. What type of antennas do you use? We use 24dbi grid antennas with 10m and 20m heliax cables.

Orjan