topic Re: command of controlleur in Wireless

command of controlleur

Dhikra Marghli — Mon, 05 Jul 2021 16:49:19 GMT

Hello

what are command that allow to configure

AP Country code.
AP Regulatory Domain............................. Unconfigured

in moblity express 1815i !!???????, that allow AP joind to controlleur

Cisco Controller) >show ap config 802.11a AP28AC.9E89.48E0AP28AC.9E89.3DB8

Cisco AP Identifier.............................. 5
Cisco AP Name.................................... AP28AC.9E89.3DB8
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-AB
AP Country code.................................. -
AP Regulatory Domain............................. Unconfigured
Switch Port Number .............................. 1
MAC Address...................................... 28:ac:9e:89:3d:b8
IP Address Configuration......................... DHCP
IP Address....................................... Disabled
Telnet State..................................... Globally Disabled
Ssh State........................................ Globally Disabled
Virtual IP Address............................... Not Configured
Cisco AP Location................................ default location
Cisco AP Floor Label............................. 0
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................

Re: command of controlleur

srkala — Fri, 08 Feb 2019 20:28:48 GMT

From the WLC CLI,

(Cisco Controller) >config ap country US ?

<Cisco AP> Enter the name of the Cisco AP.
all Configure all the Cisco APs.

(Cisco Controller) >

Re: command of controlleur

Dhikra Marghli — Sat, 09 Feb 2019 04:02:23 GMT

For AP Regulatory Domain............................. Unconfigured

how i can configured ????????? that allow AP joind to conrolleur molity express 1815i !!!???????

thanks in advance

Re: command of controlleur

Dhikra Marghli — Sat, 09 Feb 2019 07:16:46 GMT

For AP Regulatory Domain............................. Unconfigured

how i can configured ????????? that allow AP joind to conrolleur molity express 1815i !!!???????

thanks in advance

Re: command of controlleur

Leo Laohoo — Sat, 09 Feb 2019 08:20:31 GMT

@Dhikra Marghli wrote:

how i can configured ????????? that allow AP joind to conrolleur molity express 1815i !!!???????

Please read THIS.

Re: command of controlleur

Dhikra Marghli — Sat, 09 Feb 2019 08:26:55 GMT

or AP Regulatory Domain............................. Unconfigured

how i can configured Regulatory Domain in acces point 1815 !!

thanks in advance

Re: command of controlleur

Leo Laohoo — Sat, 09 Feb 2019 08:58:50 GMT

@Dhikra Marghli wrote:

how i can configured Regulatory Domain in acces point 1815 !!

Please read > THIS <.

Re: command of controlleur

Dhikra Marghli — Sat, 09 Feb 2019 09:08:45 GMT

THIS for : AP Country code

From the WLC CLI,

(Cisco Controller) >config ap country US ?

<Cisco AP> Enter the name of the Cisco AP.
all Configure all the Cisco APs.

(Cisco Controller) >

//////////////////////////////////////////////

But Also i would other command for : AP Regulatory Domain !!

if i configured code country in acce point then i would tho know if AP Regulatory Domain is show automatic !!!!!!!!!

Re: command of controlleur

Leo Laohoo — Sat, 09 Feb 2019 09:29:51 GMT

AP Regulatory Domain cannot be changed.
If the AP has the wrong Regulatory Domain, contact the vendor and ask for the AP to be swapped out with the correct Regulatory Domain.

Re: command of controlleur

Sandeep Choudhary — Wed, 13 Feb 2019 10:08:20 GMT

Configiure the country code as LEO mentioned. With country code AP will not join to it!

Regards

Dont forget to arte helpful posts