Cisco 2504 and AP1702i

linuxwiz54 — Mon, 05 Jul 2021 13:36:49 GMT

I was able to configure 2504 wireless controller once configured I plugged in the AP to POE port on 2504, I see the AP with Flashing Green but 2504 doesn't see the AP, what could be wrong any guidance will be appreciated.

the AP which I have is AIR

linuxwiz54 — Sun, 26 Feb 2017 04:32:31 GMT

the AP which I have is AIR-CAP1702I-B-K9

Paste the output of these

Sandeep Choudhary — Sun, 26 Feb 2017 11:59:21 GMT

Paste the output of these commands:

sh version from AP

sh sysinfo from WLC.

Info: If you want to join AP, then you need to setup a dhcp scope on the wlc and make sure that it must be on the same network as the wlc management. The ap will get an ip address from the pool and join the wlc as long as everything else is configured correctly.

Regards

Dont forget to rate helpful posts

I lost this post and finally

linuxwiz54 — Sun, 12 Mar 2017 02:59:33 GMT

I lost this post and finally found it

(Cisco Controller) >show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 20.0

Build Type....................................... DATA + WPS

System Name...................................... Cisco_54:88:e4
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 10.x.x.2
Last Reset....................................... Power on reset
System Up Time................................... 0 days 8 hrs 50 mins 31 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180

--More-- or (q)uit
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +26 C
External Temperature............................. +29 C
Fan Status....................................... 3200 rpm

State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0

Burned-in MAC Address............................ 00:42:5A:54:88:E0
Maximum number of APs supported.................. 5

AP00d7.8f89.22d4>sh ver
Cisco IOS Software, C1700 Software (AP3G2-RCVK9W8-M), Version 15.3(3)JD, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Fri 29-Jul-16 04:10 by prod_rel_team

ROM: Bootstrap program is C1700 boot loader
BOOTLDR: C1700 Boot Loader (AP3G2-BOOT-M) LoaderVersion 15.3() [ TRUE]

AP00d7.8f89.22d4 uptime is 9 hours, 1 minute
System returned to ROM by power-on
System image file is "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"
Last reload reason:

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

cisco AIR-CAP1702I-B-K9 (PowerPC) processor (revision A0) with 376814K/134656K bytes of memory.
Processor board ID FCW2041NLMD
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.3.102.0
1 Gigabit Ethernet interface

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:D7:8F:89:22:D4
Part Number : 73-16776-01
PCB Serial Number : FOC20395SJM
Top Assembly Part Number : 068-100893-01
Top Assembly Serial Number : FCW2041NLMD
Top Revision Number : A0
Product/Model Number : AIR-CAP1702I-B-K9

Configuration register is 0xF

Hi

Sandeep Choudhary — Sun, 12 Mar 2017 16:13:50 GMT

To join 1702 series AP , you need minimum 8.0.100.0 SW version on WLC.

Check here the comptibility matrix:

http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html

Regards

Dont forget to rate helpful posts

Is the POE port assigned to

denizyaran — Sun, 12 Mar 2017 21:19:24 GMT

Is the POE port assigned to any interface and VLAN? And can the AP receive any address?

Thank you Sandeep I upgraded

linuxwiz54 — Mon, 13 Mar 2017 03:15:29 GMT

Thank you Sandeep I upgraded the firmware to 8.0.140 and connected AP and it worked.