topic One more question. I cannot in Wireless

No Global Configuration Mode?

ChrisHudd33513 — Mon, 05 Jul 2021 09:55:46 GMT

I'm sure this has something to do the RAM or Flash memory. This is an access point that's been sitting on the shelf and as far as I knew it was working. However, I can enter privileged mode but there is no "conf t" or configure terminal option. I tried holding down the Mode button on reboot but it didn't seem to change anything. I'm just trying to gain access to the gui. I see the IP address from an IP scanner I have but am not able to access it via web browser. This is all I'm seeing from priveledged mode.

cd               Change current directory
clear            Reset functions
clock            Manage the system clock
crypto           Encryption related commands.
debug            Debugging functions (see also 'undebug')
delete           Delete a file
dir              List files on a filesystem
disable          Turn off privileged commands
enable           Turn on privileged commands
exit             Exit from the EXEC
fsck             Fsck a filesystem
help             Description of the interactive help system
led              LED functions
lock             Lock the terminal
login            Log in as a particular user
logout           Exit from the EXEC
mkdir            Create new directory
more             Display the contents of a file
name-connection Name an existing network connection
no               Disable debugging functions
ping             Send echo messages
pwd              Display current working directory
release          Release a resource
reload           Halt and perform a cold restart
rename           Rename a file
renew            Renew a resource
rmdir            Remove existing directory
save             Start to save raise_interrupt_level stack
send             Send a message to other tty lines
set              Set system parameter (not config)
show             Show running system information
systat           Display information about terminal lines
terminal         Set terminal line parameters
test             Test subsystems, memory, and interfaces
traceroute       Trace route to destination
undebug          Disable debugging functions (see also 'debug')
upgrade          Upgrade software
verify           Verify a file
where            List active connections

Thanks for the help.

Does "show version" give any

Rasika Nayanajith — Wed, 15 Apr 2015 07:19:45 GMT

Does "show version" give any output ?

Rasika

Yes, here is the output:

ChrisHudd33513 — Wed, 15 Apr 2015 21:48:36 GMT

Yes, here is the output:

AP001e.f7ee.4d02>enable

AP001e.f7ee.4d02#show version

Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(7)JX9, RELEAS E SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Tue 17-Jul-07 00:40 by tinhuang

ROM: Bootstrap program is C1130 boot loader

BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE ( fc2)

AP001e.f7ee.4d02 uptime is 22 hours, 6 minutes

System returned to ROM by power-on

System image file is "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"

cisco AIR-AP1131AG-A-K9 (PowerPCElvis) processor (revision A0) with 24566K/81 92K bytes of memory.

Processor board ID FTX1224T0LZ

PowerPCElvis CPU at 262Mhz, revision number 0x0950

Last reset from power-on

1 FastEthernet interface

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:1E:F7:EE:4D:02

Part Number : 73-8962-12

PCA Assembly Number : 800-24818-11

PCA Revision Number : B0

PCB Serial Number : FOC12225C3J

Top Assembly Part Number : 800-29230-01

Top Assembly Serial Number : FTX1224T0LZ

Top Revision Number : A0

Product/Model Number : AIR-AP1131AG-A-K9

Configuration register is 0xF

AP001e.f7ee.4d02#

HiAs I suspected this AP has

Rasika Nayanajith — Wed, 15 Apr 2015 23:42:03 GMT

As I suspected this AP has lightweight recovery image (C1130-RCVK9W8-M)

This mean you require a WLC to manage & configure this AP. If you have autonomous image (eg c1130-k9w7-tar.124-21a.JY.tar) then you can convert this to Autonomous & configure it normally.

Here is the conversion process

http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/

http://mrncciew.com/2013/12/13/ap-conversion-using-mode-button/

HTH

Rasika

*** Pls rate all useful responses ****

I wish I was a little more

ChrisHudd33513 — Thu, 16 Apr 2015 19:37:24 GMT

I wish I was a little more patient because this looks like a much simpler solution than I found. I ended up reloading the image it just took me a while to figure out how to do it. It was fun to work through it though. Thanks for the replies, I looked through the links you provided and it looks like that would have resolved it as well...and would have been easier. lol. Thanks

The AP is running in

varunag — Thu, 16 Apr 2015 19:59:20 GMT

The AP is running in Lightweight mode , WLC is required to configure Lightweight AP . So you need to convert it to Autonomous AP then you can configure it through CLI or GUI .

One more question. I cannot

ChrisHudd33513 — Fri, 17 Apr 2015 18:16:01 GMT

One more question. I cannot find a wireless controller, that I know of. I'm looking for a 2504, the one I'm used to seeing, and have yet to find it. Is there a way this can be done with SDM or using a router with a wireless controller module(which i'm still looking for)?