topic working with CT5508 in Wireless

working with CT5508

Debudas123 — Mon, 05 Jul 2021 07:09:49 GMT

Dear,

i have 12 caps(3602) and one 5508 controller, i have configure all the things, but when i have enable the hight-thoughput (n mode), then no win7 laptops are connecting, but when i will disable it then it is connected with 54 mbps, so what will be the issue.

thanks

Debu

working with CT5508

Leo Laohoo — Wed, 12 Feb 2014 07:52:04 GMT

For 802.11n, you need a minimum of OPEN authentication or WPA2 AES/PSK.

working with CT5508

Sandeep Choudhary — Wed, 12 Feb 2014 07:58:23 GMT

adding to LEO..

Please check the followings :

1. WLAN is WMM enabled

2. Security must be WPA2+AES or Open

(If you dont meet these 2 requirements you wont be able to push HT rates)

3. 802.11n Rates and support should be enabled on the network (a or b/g)

Regards

working with CT5508

Victor Vasantha Kumar — Wed, 12 Feb 2014 08:09:12 GMT

Some drivers behave weird when you configure the WLAN for mixed mode ( TKIP and AES enabled ).

If that is the case, please remove TKIP and have them on ONLY AES.

Regards
Victor V

*****Help out other by using the rating system and marking answered questions as *****Answered"*****

Re: working with CT5508

Debudas123 — Wed, 12 Feb 2014 08:47:41 GMT

Hi,

everything is configured properly as required, but still unable to connect, please see the attachment.

Thanks

Debu

Re: working with CT5508

Sandeep Choudhary — Wed, 12 Feb 2014 08:55:56 GMT

HI Debu,

Take a windows 7 pc, note down the mac address and try to connect to wlan.

on the same time you can run this commands on WLC: debug client <mac address>

Regards

Re: working with CT5508

Leo Laohoo — Wed, 12 Feb 2014 09:09:05 GMT

Please post the output to the WLC command of "sh wlan ".

Can you also specify the model of the wireless NIC card of the client along with the version of the driver used?

working with CT5508

Debudas123 — Wed, 12 Feb 2014 09:24:09 GMT

see the details

(Cisco Controller) >debug client 20:7C:8F:32:43:FA

(Cisco Controller) >*apfMsConnTask_6: Feb 12 14:46:56.488: 20:7c:8f:32:43:fa Ass
ociation received from mobile on BSSID 7c:95:f3:8a:26:e1
*apfMsConnTask_6: Feb 12 14:46:56.488: 20:7c:8f:32:43:fa Global 200 Clients are
allowed to AP radio

*apfMsConnTask_6: Feb 12 14:46:56.488: 20:7c:8f:32:43:fa Max Client Trap Thresho
ld: 0 cur: 1

*apfMsConnTask_6: Feb 12 14:46:56.488: 20:7c:8f:32:43:fa Rf profile 600 Clients
are allowed to AP wlan

*apfMsConnTask_6: Feb 12 14:46:56.488: 20:7c:8f:32:43:fa Applying Interface poli
cy on Mobile, role Local. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 0

*apfMsConnTask_6: Feb 12 14:46:56.488: 20:7c:8f:32:43:fa Re-applying interface p
olicy for client

*apfMsConnTask_6: Feb 12 14:46:56.488: 20:7c:8f:32:43:fa 10.10.3.79 RUN (20) Cha
nging IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_poli
cy.c:2018)
*apfMsConnTask_6: Feb 12 14:46:56.488: 20:7c:8f:32:43:fa 10.10.3.79 RUN (20) Cha
nging IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_poli
cy.c:2246)
*apfMsConnTask_6: Feb 12 14:46:56.488: 20:7c:8f:32:43:fa In processSsidIE:4309 s
etting Central switched to TRUE
*apfMsConnTask_6: Feb 12 14:46:56.488: 20:7c:8f:32:43:fa In processSsidIE:4312 a
pVapId = 2 and Split Acl Id = 65535
*apfMsConnTask_6: Feb 12 14:46:56.488: 20:7c:8f:32:43:fa Applying site-specific
Local Bridging override for station 20:7c:8f:32:43:fa - vapId 2, site 'default-g
roup', interface 'management'
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa Applying Local Bridging
Interface Policy for station 20:7c:8f:32:43:fa - vlan 0, interface id 0, interf
ace 'management'
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa processSsidIE statusCo
de is 0 and status is 0
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa processSsidIE ssid_don
e_flag is 0 finish_flag is 0
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa STA - rates (8): 130 13
2 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa suppRates statusCode i
s 0 and gotSuppRatesElement is 1
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa STA - rates (12): 130 1
32 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa extSuppRates statusCod
e is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa Processing RSN IE type
48, length 20 for mobile 20:7c:8f:32:43:fa
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa apfMsRunStateDec
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa apfMs1xStateDec
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa 10.10.3.79 RUN (20) Cha
nge state to START (0) last state RUN (20)

*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa pemApfAddMobileStation2
: APF_MS_PEM_WAIT_L2_AUTH_COMPLETE = 0.
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa 10.10.3.79 START (0) In
itializing policy
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa 10.10.3.79 START (0) Ch
ange state to AUTHCHECK (2) last state START (0)

*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa 10.10.3.79 AUTHCHECK (2
) Change state to 8021X_REQD (3) last state AUTHCHECK (2)

*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa Not Using WMM Complianc
e code qosCap 00
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa 10.10.3.79 8021X_REQD (
3) Plumbed mobile LWAPP rule on AP 7c:95:f3:8a:26:e0 vapId 2 apVapId 2 flex-acl-
name:
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa apfPemAddUser2 (apf_pol
icy.c:276) Changing state for mobile 20:7c:8f:32:43:fa on AP 7c:95:f3:8a:26:e0 f
rom Associated to Associated

*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa apfPemAddUser2:session
timeout forstation 20:7c:8f:32:43:fa - Session Tout 1800, apfMsTimeOut '1800' an
d sessionTimerRunning flag is 0
*apfMsConnTask_6: Feb 12 14:46:56.489: 20:7c:8f:32:43:fa Scheduling deletion of
Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_6: Feb 12 14:46:56.490: 20:7c:8f:32:43:fa Func: apfPemAddUser2, M
s Timeout = 1800, Session Timeout = 1800

*apfMsConnTask_6: Feb 12 14:46:56.490: 20:7c:8f:32:43:fa Sending Assoc Response
to station on BSSID 7c:95:f3:8a:26:e1 (status 0) ApVapId 2 Slot 0
*apfMsConnTask_6: Feb 12 14:46:56.490: 20:7c:8f:32:43:fa apfProcessAssocReq (apf
_80211.c:7510) Changing state for mobile 20:7c:8f:32:43:fa on AP 7c:95:f3:8a:26:
e0 from Associated to Associated

*pemReceiveTask: Feb 12 14:46:56.491: 20:7c:8f:32:43:fa 10.10.3.79 Removed NPU e
ntry.
*spamApTask7: Feb 12 14:46:56.492: 20:7c:8f:32:43:fa Sent 1x initiate message to
multi thread task for mobile 20:7c:8f:32:43:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: 20:7c:8f:32:43:fa Creating a PKC PMKID
Cache entry for station 20:7c:8f:32:43:fa (RSN 2)
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: 20:7c:8f:32:43:fa Resetting MSCB PMK C
ache Entry 0 for station 20:7c:8f:32:43:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: 20:7c:8f:32:43:fa Removing BSSID 7c:95
:f3:8a:26:e1 from PMKID cache of station 20:7c:8f:32:43:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: 20:7c:8f:32:43:fa Setting active key c
ache index 0 ---> 8
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: 20:7c:8f:32:43:fa Setting active key c
ache index 8 ---> 0
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: 20:7c:8f:32:43:fa Adding BSSID 7c:95:f
3:8a:26:e1 to PMKID cache at index 0 for station 20:7c:8f:32:43:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: New PMKID: (16)

*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: [0000] f9 f6 8a d9 9c ab 71 d8 80
22 28 64 a7 0a cf 5c

*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: 20:7c:8f:32:43:fa Initiating RSN PSK t
o mobile 20:7c:8f:32:43:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: 20:7c:8f:32:43:fa dot1x - moving mobil
e 20:7c:8f:32:43:fa into Force Auth state
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: 20:7c:8f:32:43:fa Found an cache entry
for BSSID 7c:95:f3:8a:26:e1 in PMKID cache at index 0 of station 20:7c:8f:32:43
:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: 20:7c:8f:32:43:fa Found an cache entry
for BSSID 7c:95:f3:8a:26:e1 in PMKID cache at index 0 of station 20:7c:8f:32:43
:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: Including PMKID in M1 (16)

*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: [0000] f9 f6 8a d9 9c ab 71 d8 80
22 28 64 a7 0a cf 5c

*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: 20:7c:8f:32:43:fa Starting key exchang
e to mobile 20:7c:8f:32:43:fa, data packets will be dropped
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.492: 20:7c:8f:32:43:fa Sending EAPOL-Key Me
ssage to mobile 20:7c:8f:32:43:fa
state INITPMK (message 1), replay counter 00
.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.497: 20:7c:8f:32:43:fa Received EAPOL-Key f
rom mobile 20:7c:8f:32:43:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.497: 20:7c:8f:32:43:fa Ignoring invalid EAP
OL version (1) in EAPOL-key message from mobile 20:7c:8f:32:43:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.497: 20:7c:8f:32:43:fa Received EAPOL-key i
n PTK_START state (message 2) from mobile 20:7c:8f:32:43:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.498: 20:7c:8f:32:43:fa Stopping retransmiss
ion timer for mobile 20:7c:8f:32:43:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.498: 20:7c:8f:32:43:fa Sending EAPOL-Key Me
ssage to mobile 20:7c:8f:32:43:fa
state PTKINITNEGOTIATING (message 3), replay
counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa Received EAPOL-Key f
rom mobile 20:7c:8f:32:43:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa Ignoring invalid EAP
OL version (1) in EAPOL-key message from mobile 20:7c:8f:32:43:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa Received EAPOL-key i
n PTKINITNEGOTIATING state (message 4) from mobile 20:7c:8f:32:43:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa Stopping retransmiss
ion timer for mobile 20:7c:8f:32:43:fa
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa apfMs1xStateInc
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa 10.10.3.79 8021X_REQ
D (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)

*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa Not Using WMM Compli
ance code qosCap 00
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa 10.10.3.79 L2AUTHCOM
PLETE (4) Plumbed mobile LWAPP rule on AP 7c:95:f3:8a:26:e0 vapId 2 apVapId 2 fl
ex-acl-name:
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa apfMsRunStateInc
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa 10.10.3.79 L2AUTHCOM
PLETE (4) Change state to RUN (20) last state L2AUTHCOMPLETE (4)

*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa 10.10.3.79 RUN (20)
Reached PLUMBFASTPATH: from line 6076
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa 10.10.3.79 RUN (20)
Adding Fast Path rule
type = Airespace AP Client
on AP 7c:95:f3:8a:26:e0, slot 0, interface = 13, QOS = 0
IPv4 ACL ID = 255, IPv6 ACL ID = 25
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa 10.10.3.79 RUN (20)
Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging
Vlan = 0, Local Bridging intf id = 0
*Dot1x_NW_MsgTask_2: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa 10.10.3.79 RUN (20)
Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
*pemReceiveTask: Feb 12 14:46:56.503: 20:7c:8f:32:43:fa 10.10.3.79 Added NPU ent
ry of type 1, dtlFlags 0x0

(Cisco Controller) >

thank

Debu

working with CT5508

Debudas123 — Wed, 12 Feb 2014 09:32:23 GMT

(Cisco Controller) >show wlan 2

WLAN Identifier.................................. 2
Profile Name..................................... test
Network Name (SSID).............................. test
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status ....................... Disabled
DHCP ......................................... Disabled
HTTP ......................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ 300 seconds

--More-- or (q)uit
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... ASU
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
mDNS Status...................................... Enabled
mDNS Profile Name................................ default-mdns-profile
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
PMIPv6 Mobility Type............................. none
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream      Downstream
Average Data Rate................................   0             0
Average Realtime Data Rate.......................   0             0
Burst Data Rate..................................   0             0
Burst Realtime Data Rate.........................   0             0
Per-Client Rate Limits........................... Upstream      Downstream
Average Data Rate................................   0             0
Average Realtime Data Rate.......................   0             0

--More-- or (q)uit
Burst Data Rate..................................   0             0
Burst Realtime Data Rate.........................   0             0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
   Authentication................................ Global Servers
   Accounting.................................... Global Servers
      Interim Update............................. Disabled
   Dynamic Interface............................. Disabled
   Dynamic Interface Priority.................... wlan

--More-- or (q)uit
Local EAP Authentication......................... Disabled
Security

   802.11 Authentication:........................ Open System
   FT Support.................................... Disabled
   Static WEP Keys............................... Disabled
   802.1X........................................ Disabled
   Wi-Fi Protected Access (WPA/WPA2)............. Enabled
      WPA (SSN IE)............................... Disabled
      WPA2 (RSN IE).............................. Enabled
         TKIP Cipher............................. Disabled
         AES Cipher.............................. Enabled
                                                               Auth Key Manageme
nt
         802.1x.................................. Disabled
         PSK..................................... Enabled
         CCKM.................................... Disabled
         FT-1X(802.11r).......................... Disabled
         FT-PSK(802.11r)......................... Disabled
         PMF-1X(802.11w)......................... Disabled
         PMF-PSK(802.11w)........................ Disabled
      FT Reassociation Timeout................... 20
      FT Over-The-DS mode........................ Enabled
      GTK Randomization.......................... Disabled

--More-- or (q)uit
      SKC Cache Support.......................... Disabled
      CCKM TSF Tolerance......................... 1000
   WAPI.......................................... Disabled
   Wi-Fi Direct policy configured................ Disabled
   EAP-Passthrough............................... Disabled
   CKIP ......................................... Disabled
   Web Based Authentication...................... Disabled
   Web-Passthrough............................... Disabled
   Conditional Web Redirect...................... Disabled
   Splash-Page Web Redirect...................... Disabled
   Auto Anchor................................... Disabled
   FlexConnect Local Switching................... Disabled
   flexconnect Central Dhcp Flag................. Disabled
   flexconnect nat-pat Flag...................... Disabled
   flexconnect Dns Override Flag................. Disabled
   FlexConnect Vlan based Central Switching ..... Disabled
   FlexConnect Local Authentication.............. Disabled
   FlexConnect Learn IP Address.................. Enabled
   Client MFP.................................... Optional
   PMF........................................... Disabled
   PMF Association Comeback Time................. 1
   PMF SA Query RetryTimeout..................... 200
   Tkip MIC Countermeasure Hold-down Timer....... 60

--More-- or (q)uit
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Disabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled

Mobility Anchor List
WLAN ID IP Address Status
------- --------------- ------

802.11u........................................ Disabled

MSAP Services.................................. Disabled

--More-- or (q)uit

(Cisco Controller) >

Re: working with CT5508

Leo Laohoo — Wed, 12 Feb 2014 09:41:12 GMT

Number of Active Clients......................... 0

"0" clients?

Can you please post the output to this command: sh client detail 20:7c:8f:32:43:fa

Re: working with CT5508

Sandeep Choudhary — Wed, 12 Feb 2014 09:48:41 GMT

no error in these logs....can you tell me from where clients are getting IP address ???

also paste the complete logs

Regards

working with CT5508

Debudas123 — Wed, 12 Feb 2014 09:51:09 GMT

yes

nobody can connect, thats why its showing 0 active clients

thanks

debu

working with CT5508

Leo Laohoo — Wed, 12 Feb 2014 09:55:40 GMT

but when i have enable the hight-thoughput (n mode), then no win7 laptops are connecting,

So what is the model of the wireless NIC?

working with CT5508

Debudas123 — Wed, 12 Feb 2014 09:59:14 GMT

see the details, its showing limited access on win7

(Cisco Controller)
User: admin
Password:*********
(Cisco Controller) >show client detail 20:7c:8f:32:43:fa
Client MAC Address............................... 20:7c:8f:32:43:fa
Client Username ................................. N/A
AP MAC Address................................... dc:a5:f4:b9:33:e0
AP Name.......................................... CAP-MAP-03
Client State..................................... Associated
Client NAC OOB State............................. Access
Wireless LAN Id.................................. 2
Hotspot (802.11u)................................ Not Supported
BSSID............................................ dc:a5:f4:b9:33:e1
Connected For ................................... 221 secs
Channel.......................................... 11
IP Address....................................... 10.10.3.79
Gateway Address.................................. Unknown
Netmask.......................................... Unknown
IPv6 Address..................................... fe80::d017:9f65:a955:bf86
Association Id................................... 1
Authentication Algorithm......................... Open System
Reason Code...................................... 1
Status Code...................................... 0
Session Timeout.................................. 1800
Client CCX version............................... No CCX support
QoS Level........................................ Silver

--More-- or (q)uit
802.1P Priority Tag.............................. disabled
CTS Security Group Tag........................... Not Applicable
KTS CAC Capability............................... No
WMM Support...................................... Enabled
APSD ACs....................................... BK BE VI VO
Power Save....................................... OFF
Current Rate..................................... m7
Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
............................................. 12.0,18.0,24.0,36.0,48.0,
............................................. 54.0
Mobility State................................... Local
Mobility Move Count.............................. 0
Security Policy Completed........................ Yes
Policy Manager State............................. RUN
Policy Manager Rule Created...................... Yes
Audit Session ID................................. none
IPv4 ACL Name.................................... none
IPv4 ACL Applied Status.......................... Unavailable
IPv6 ACL Name.................................... none
IPv6 ACL Applied Status.......................... Unavailable
Client Type...................................... SimpleIP
PMIPv6 State..................................... Unavailable
mDNS Status...................................... Enabled

--More-- or (q)uit
mDNS Profile Name................................ default-mdns-profile
No. of mDNS Services Advertised.................. 0
Policy Type...................................... WPA2
Authentication Key Management.................... PSK
Encryption Cipher................................ CCMP (AES)
Protected Management Frame ...................... No
Management Frame Protection...................... No
EAP Type......................................... Unknown
Interface........................................ management
VLAN............................................. 0
Quarantine VLAN.................................. 0
Access VLAN...................................... 0
Client Capabilities:
      CF Pollable................................ Not implemented
      CF Poll Request............................ Not implemented
      Short Preamble............................. Implemented
      PBCC....................................... Not implemented
      Channel Agility............................ Not implemented
      Listen Interval............................ 1
      Fast BSS Transition........................ Not implemented
Client Wifi Direct Capabilities:
      WFD capable................................ No
      Manged WFD capable......................... No

--More-- or (q)uit
      Cross Connection Capable................... No
      Support Concurrent Operation............... No
Fast BSS Transition Details:
Client Statistics:
      Number of Bytes Received................... 38274
      Number of Bytes Sent....................... 331
      Number of Packets Received................. 440
      Number of Packets Sent..................... 3
      Number of Interim-Update Sent.............. 0
      Number of EAP Id Request Msg Timeouts...... 0
      Number of EAP Id Request Msg Failures...... 0
      Number of EAP Request Msg Timeouts......... 0
      Number of EAP Request Msg Failures......... 0
      Number of EAP Key Msg Timeouts............. 0
      Number of EAP Key Msg Failures............. 0
      Number of Data Retries..................... 0
      Number of RTS Retries...................... 0
      Number of Duplicate Received Packets....... 0
      Number of Decrypt Failed Packets........... 0
      Number of Mic Failured Packets............. 0
      Number of Mic Missing Packets.............. 0
      Number of RA Packets Dropped............... 0
      Number of Policy Errors.................... 0

--More-- or (q)uit
      Radio Signal Strength Indicator............ -20 dBm
      Signal to Noise Ratio...................... 74 dB
Client Rate Limiting Statistics:
      Number of Data Packets Recieved............ 0
      Number of Data Rx Packets Dropped.......... 0
      Number of Data Bytes Recieved.............. 0
      Number of Data Rx Bytes Dropped............ 0
      Number of Realtime Packets Recieved........ 0
      Number of Realtime Rx Packets Dropped...... 0
      Number of Realtime Bytes Recieved.......... 0
      Number of Realtime Rx Bytes Dropped........ 0
      Number of Data Packets Sent................ 0
      Number of Data Tx Packets Dropped.......... 0
      Number of Data Bytes Sent.................. 0
      Number of Data Tx Bytes Dropped............ 0
      Number of Realtime Packets Sent............ 0
      Number of Realtime Tx Packets Dropped...... 0
      Number of Realtime Bytes Sent.............. 0
      Number of Realtime Tx Bytes Dropped........ 0
Nearby AP Statistics:
      CAP-MAP-02(slot 0)
        antenna1: 62 secs ago.................... -37 dBm
      CAP-MAP-01(slot 0)

--More-- or (q)uit
        antenna0: 61 secs ago.................... -41 dBm
      CAP-RAP-01(slot 0)
        antenna0: 0 secs ago..................... -19 dBm
        antenna1: 0 secs ago..................... -39 dBm
      IT-GR-FLR-AP01(slot 0)
        antenna0: 0 secs ago..................... -40 dBm
        antenna1: 0 secs ago..................... -49 dBm
      CAP-MAP-03(slot 0)
        antenna0: 59 secs ago.................... -18 dBm
        antenna1: 59 secs ago.................... -28 dBm
DNS Server details:
      DNS server IP ............................. 0.0.0.0
      DNS server IP ............................. 0.0.0.0
Assisted Roaming Prediction List details:

Client Dhcp Required: False

(Cisco Controller) >

working with CT5508

Leo Laohoo — Wed, 12 Feb 2014 10:03:03 GMT

I have a feeling your PC's wireless card does not support 802.11n. I believe it will only support 802.11 b/g and could be falsely advertised as "802.11 b/g/n ready".

working with CT5508

Debudas123 — Wed, 12 Feb 2014 10:07:19 GMT

i have tried lots of laptop, same problem, but winxp is working very fine(in g mode)

Thanks

Debu

working with CT5508

Debudas123 — Wed, 12 Feb 2014 10:11:31 GMT

this problem is in only win7 laptop, winxp are working fine

thanks

Debu

working with CT5508

Leo Laohoo — Wed, 12 Feb 2014 10:34:44 GMT

this problem is in only win7 laptop

Can you specify the model of the wireless NIC driver and the version of the drivers?

working with CT5508

Debudas123 — Wed, 12 Feb 2014 10:35:01 GMT

windows 7 are not connecting, but winxp, macbook and mobiles are connected...

thanks

Debu

Re: working with CT5508

Leo Laohoo — Wed, 12 Feb 2014 10:38:04 GMT

windows 7 are not connecting, but winxp, macbook and mobiles are connected...

This sounds like drivers as well. Are the Windows 7 clients the same hardware?

Have you tried upgrading the drivers of the Windows 7 wireless NIC?

What happens if you use OPEN authentication, can the Windows 7 client associate?