topic blue indicator light on 1131 in Wireless

blue indicator light on 1131

lcaruso — Sun, 04 Jul 2021 02:42:21 GMT

The ringed indicator light on the 1131 normally glows green. What is indicated when it is glowing blue instead? Is this a power issue?

Re: blue indicator light on 1131

Madhuri C — Sat, 22 Jan 2011 01:27:36 GMT

Hi,

Please take a look at the below table:

Table 3-1 LED Signals
Message type	Cable Bay Area		Top of Unit	Meaning
Message type	Ethernet LED	Radio LED	Status LED	Meaning
Operating status	Green	—	—	Ethernet link is operational.
	Blinking green	—	—	Transmitting or receiving Ethernet packets.
	—	Blinking green	—	Transmitting or receiving radio packets.
	—	—	Blinking dark blue	Software upgrade in progress
Association status	—	—	Light green	Normal operating condition, but no wireless client devices are associated with the unit.
Association status	—	—	Blue	Normal operating condition, at least one wireless client device is associated with the unit.
Cisco IOS errors	Blinking amber	—	—	Transmit or receive Ethernet errors.
	—	Blinking amber	—	Maximum retries or buffer full occurred on the radio.
	Red	Red	Amber	Software failure; try disconnecting and reconnecting unit power.
	—	—	Amber	General warning, insufficient inline power (see the "Low Power Condition for Autonomous Access Points" section).
Boot loader status	Green	Green	Green	DRAM memory test ok.
	Off	Blinking green	Blue-green	Initialize Flash file system.
	Off	Green	Pink	Flash memory test ok.
	Green	Off	Dark blue	Ethernet test ok.
	Green	Green	Green	Starting Cisco IOS.
Boot loader warnings	Off	Off	Yellow	Ethernet link not operational.
	Red	Off	Yellow	Ethernet failure.
	Amber	Off	Yellow	Configuration recovery in progress (Mode button pressed for 2 to 3 seconds).
	Off	Red	Pink	Image recovery (Mode button pressed for 20 to 30 seconds).
	Blinking green	Blinking red	Blinking pink	Image recovery in progress and Mode button is released.
Boot loader errors	Red	Red	Red	DRAM memory test failure.
	Off	Red	Blinking red and blue	Flash file system failure.
	Off	Amber	Blinking red and blue-green	Environment variable (ENVAR) failure.
	Amber	Off	Blinking red and yellow	Bad MAC address.
	Red	Off	Blinking red and off	Ethernet failure during image recovery.
	Amber	Amber	Blinking red and off	Boot environment error.
	Red	Amber	Blinking red and off	No Cisco IOS image file.
	Amber	Amber	Blinking red and off	Boot failure.

Link : http://www.cisco.com/en/US/docs/wireless/access_point/1130/installation/guide/113h_c3.html#wpxref37237

Regards,

Madhuri

Re: blue indicator light on 1131

Madhuri C — Sat, 22 Jan 2011 01:31:20 GMT

Hi,

If AP is in LWAP mode then please refer to : http://www.cisco.com/en/US/docs/wireless/access_point/1130/installation/guide/113h_c4.html#wp1030793

Regards,

Madhuri

Re: blue indicator light on 1131

lcaruso — Sat, 22 Jan 2011 04:03:04 GMT

thank you.

Re: blue indicator light on 1131

George Stefanick — Sat, 22 Jan 2011 06:06:10 GMT

LIGHT GREEN = Access Point is operational, but no wireless clients are attached

BLUE = Access point is opertional and atleast 1 wireless is associated to the AP

ORANGE = Power issue at the access point

RED = Firmware issue

blue indicator light on 1131

mgallmann — Mon, 08 Jul 2013 17:02:25 GMT

I have an combination of lights that are not named in the Cisco 1131G-A-K9 manuals, The Status LED is a constant pink. The ethernet is blinking green with standard activity. I've been unable to get the SSID to broadcast despite trying different software versions (currently c1130-k9w7-tar.123-4.JA2) and double-checking my configurations. I've checked the flash file system. The image's were updated using HTTP. I've scoured the internet to no avail. Any help would be appreciated. Thanks.

blue indicator light on 1131

Scott Fella — Mon, 08 Jul 2013 17:06:23 GMT

Console into the AP and reboot the AP and post the output. That will have the reason why its like that.

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

Re: blue indicator light on 1131

Scott Fella — Mon, 08 Jul 2013 18:22:31 GMT

This is autonomous, so do you have it in a 802.af PoE switch

Sent from Cisco Technical Support iPhone App

Re: blue indicator light on 1131

Scott Fella — Mon, 08 Jul 2013 18:26:40 GMT

If its a power issue, take a look at this doc

http://www.cisco.com/en/US/docs/wireless/access_point/1130/installation/guide/113h_c3.html#wp1057645

Sent from Cisco Technical Support iPhone App

blue indicator light on 1131

mgallmann — Mon, 08 Jul 2013 18:30:18 GMT

No it's being powered by the 48V adapter. The ethernet runs to a Cisco 4507 which I believe does not support POE.

blue indicator light on 1131

Scott Fella — Mon, 08 Jul 2013 18:54:15 GMT

You have ssid's configured for the AP? can you post your show run-config?

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

blue indicator light on 1131

mgallmann — Mon, 08 Jul 2013 19:11:56 GMT

Alright. So at first I just configured the SSID. Now when I exit out of the web browser and open up a telnet session there are configurations that I never even made ( the ip RADIUS source, and the SNMP). I've been careful not to have two management connections open while making changes.

ap>en
Password:
ap#sh run
ap#sh running-config
Building configuration...

Current configuration : 1933 bytes
!
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
enable secret 5 $1$Iqff$NwLuIeARC7kTVaXtlHVIB0
!
username Cisco password 7 1531021F0725
ip subnet-zero
ip domain name westernind.com
ip name-server 192.168.34.32
!
!
no aaa new-model
!
dot11 ssid WTGarlandAP
authentication open
!
power inline negotiation prestandard source
!
!
!
bridge irb
!
!
interface Dot11Radio0
no ip address
no ip route-cache
!
encryption key 1 size 128bit 7 F2F80C353D3AD67412F9CD485817 transmit-key
encryption mode wep mandatory
!
ssid WTGarlandAP
!
short-slot-time
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
rts threshold 500
rts retries 50
packet retries 50
station-role root
beacon period 50
beacon dtim-period 50
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
hold-queue 160 in
!
interface BVI1
ip address 192.168.34.82 255.255.255.0
no ip route-cache
!
ip default-gateway 192.168.34.31
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
!
logging snmp-trap emergencies
logging snmp-trap alerts
logging snmp-trap critical
logging snmp-trap errors
logging snmp-trap warnings
!
control-plane
!
bridge 1 route ip
!
!
!
line con 0
transport preferred all
transport output all
line vty 0 4
login local
transport preferred all
transport input all
transport output all
line vty 5 15
login
transport preferred all
transport input all
transport output all
!
end

ap#

blue indicator light on 1131

mgallmann — Mon, 08 Jul 2013 19:21:05 GMT

And when I went into NETWORK INTERFACES > RADIO0-802.11g > SETTINGS (tab) before I could apply the "ENABLE" button it was asking me to put in the RTS Threshold and the DTIM, which I've never had it do. But perhaps it was because Im using an earlier version than before. Random question: Do the system software and bootloader versions have to be the same?

blue indicator light on 1131

Scott Fella — Mon, 08 Jul 2013 19:25:14 GMT

I usually use the command line for the confiugration, so really have no clue what the gui will ask. As far as the bootloader, as long as its not too far off, then that is fine. I have never had to upgrade the bootloader, but thats just me:)

Can you post your show ip int brief

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

blue indicator light on 1131

mgallmann — Mon, 08 Jul 2013 20:26:37 GMT

Interface                  IP-Address      OK? Method Status                Protocol
BVI1                       192.168.34.82   YES NVRAM up                    up
Dot11Radio0                unassigned      YES NVRAM up                    up
FastEthernet0              unassigned      YES NVRAM up                    up

blue indicator light on 1131

Scott Fella — Mon, 08 Jul 2013 20:29:52 GMT

So it looks like the radio is up... so are you able to connect?

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

blue indicator light on 1131

mgallmann — Mon, 08 Jul 2013 20:57:26 GMT

I was able to connect but I had to type in the SSID of the AP on an employees laptop. I want the SSID to be broadcasted so that everyone can see it. I just assumed after you enabled the radio and put the settings in it would automatically broadcast.

blue indicator light on 1131

mgallmann — Tue, 09 Jul 2013 13:41:02 GMT

After I had a client associate to the AP.....the SSID seems to be broadcasting all of a sudden. I'm worried what's going to happen when I change it to PoE. Thank you for your help.

blue indicator light on 1131

T3chSlave — Tue, 09 Jul 2013 18:23:48 GMT

Alright same person different name. I've been able to get the SSID broadcasting but it's also broadcasting "Other Network" even after turning some of the Guest SSID's on and off to see if anything made it go away. Nothing has worked.

Re: blue indicator light on 1131

Scott Fella — Tue, 09 Jul 2013 19:56:53 GMT

Post an updated show run-config.

You sure your not seeing the SSID from another ap that might have it broadcasting.

Sent from Cisco Technical Support iPhone App