topic Re: Factory settings !!! in Wireless https://community.cisco.com/t5/wireless/factory-settings/m-p/1117695#M213114 <HTML><HEAD></HEAD><BODY><P>Hi Paul,</P><P></P><P>you might want to try the following.</P><P></P><P>First be sure it is an IOS running AP not an LWAPP upgraded one.</P><P></P><P>Open the sliding cover.</P><P></P><P>Unplug any cabling.</P><P></P><P>Next to the LEDs poke gently in the hole with something pointed; pen for example.</P><P></P><P>While you keep the pen in the hole plug in power.</P><P></P><P>Wait for about 5 seconds (but less than about 30s) until one of the LED goes amber (orange).</P><P></P><P>Pull out the pen.</P><P></P><P>Let the box boot (1Minute)</P><P></P><P>Connect console cable .</P><P></P><P>Login with terminal emulation of your choice.</P><P></P><P>Usernames and Passwords default to "Cisco"</P><P></P><P>Type: enable</P><P>Type: erase start</P><P>Confirm following questions</P><P></P><P>Wait while box reboots</P><P></P><P>You have a shiny out of the box box</P><P></P><P>regards</P><P></P><P>Hermann</P><P></P><P></P></BODY></HTML> Thu, 06 Nov 2008 08:28:40 GMT h-zenk 2008-11-06T08:28:40Z Factory settings !!! https://community.cisco.com/t5/wireless/factory-settings/m-p/1117694#M213113 <P>Hi, i need to erase de configuration file in 1131 AG-A K9. is an Autonumos series. and i can not set any configuration unless i erase the the NVRAM. i Have try loooking for any troubble shouting guide but nothign helps. any information it will be apreciated thanks</P> Sat, 03 Jul 2021 23:44:08 GMT https://community.cisco.com/t5/wireless/factory-settings/m-p/1117694#M213113 Paul Webster 2021-07-03T23:44:08Z Re: Factory settings !!! https://community.cisco.com/t5/wireless/factory-settings/m-p/1117695#M213114 <HTML><HEAD></HEAD><BODY><P>Hi Paul,</P><P></P><P>you might want to try the following.</P><P></P><P>First be sure it is an IOS running AP not an LWAPP upgraded one.</P><P></P><P>Open the sliding cover.</P><P></P><P>Unplug any cabling.</P><P></P><P>Next to the LEDs poke gently in the hole with something pointed; pen for example.</P><P></P><P>While you keep the pen in the hole plug in power.</P><P></P><P>Wait for about 5 seconds (but less than about 30s) until one of the LED goes amber (orange).</P><P></P><P>Pull out the pen.</P><P></P><P>Let the box boot (1Minute)</P><P></P><P>Connect console cable .</P><P></P><P>Login with terminal emulation of your choice.</P><P></P><P>Usernames and Passwords default to "Cisco"</P><P></P><P>Type: enable</P><P>Type: erase start</P><P>Confirm following questions</P><P></P><P>Wait while box reboots</P><P></P><P>You have a shiny out of the box box</P><P></P><P>regards</P><P></P><P>Hermann</P><P></P><P></P></BODY></HTML> Thu, 06 Nov 2008 08:28:40 GMT https://community.cisco.com/t5/wireless/factory-settings/m-p/1117695#M213114 h-zenk 2008-11-06T08:28:40Z