Cisco LAP 1522

Emmanouil Patiniotakis — Sun, 04 Jul 2021 05:37:04 GMT

Sorry for this stupid question,

but is there anyway to access directly a LAP 1522 using a console port?

Best Regards.

Re: Cisco LAP 1522

Scott Fella — Wed, 05 Sep 2012 11:46:49 GMT

I believe they do... I know the 1550's do, but it's been years since I touched the 1520's. Bad memory.. The initial mesh APs didn't have console though.

http://www.cisco.com/en/US/docs/wireless/technology/mesh/7.0/design/guide/MeshAP_70.html#wp1294976

Sent from Cisco Technical Support iPhone App

Cisco LAP 1522

Emmanouil Patiniotakis — Wed, 05 Sep 2012 12:05:16 GMT

I have managed to access the CLI but although I can see the log messages I cannot type any commands. Do you have any idea why this is happening?

Re: Cisco LAP 1522

Scott Fella — Wed, 05 Sep 2012 12:34:47 GMT

It should be the same commands as for any lightweight access point. This is different from autonomous.

Sent from Cisco Technical Support iPhone App

Re: Cisco LAP 1522

Stephen Rodriguez — Wed, 05 Sep 2012 12:45:08 GMT

Make sure you are set for 9600/none/8/1 and flow control is off

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered

Cisco LAP 1522

Emmanouil Patiniotakis — Wed, 05 Sep 2012 13:06:47 GMT

Yes all the settings are as you suggested. Scott the problem is that it does not allow me to type anything. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.

IOS Bootloader - Starting system.

Xmodem file system is available.

flashfs[0]: 18 files, 2 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 31868928

flashfs[0]: Bytes used: 15537664

flashfs[0]: Bytes available: 16331264

flashfs[0]: flashfs fsck took 23 seconds.

Reading cookie from flash parameter block...done.

Base Ethernet MAC address: 00:27:0c:27:3f:00

Low Power PoE - enabling LAN Ethernet port only

Loading "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB"...###################################################################################################################################################################################################

File "flash:/c1520-k9w8-mx.124-21a.JHB/c1520-k9w8-mx.124-21a.JHB" uncompressed and installed, entry point: 0x3000

executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

Rights clause at FAR sec. 52.227-19 and subparagraph

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Tue 06-Jul-10 14:49 by prod_rel_team

Proceeding with system init

Proceeding to unmask interrupts

Initializing flashfs...

flashfs[1]: 18 files, 2 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 31352832

flashfs[1]: Bytes used: 15537664

flashfs[1]: Bytes available: 15815168

flashfs[1]: flashfs fsck took 5 seconds.

flashfs[1]: Initialization complete....done Initializing flashfs.

Warning: the compile-time code checksum does not appear to be present.

Radio0 present A600 8000 A8020000 0 A8030000 30

Radio1 present A600 8000 B8020000 0 B8030000 13

Radio2 not present 0 0 0 0 0 11

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

%Error opening flash:/c1520-rcvk9w8-mx/info (No such file or directory)cisco AIR-LAP1522AG-E-K9 (PowerPC 8349) processor (revision A0) with 49142K/16384K bytes of memory.

Processor board ID FCW1346W00Q

PowerPC 8349 CPU at 533Mhz, revision number 0x0031

Last reset from power loss

LWAPP image version 6.0.199.0

4 Gigabit Ethernet interfaces

2 802.11 Radio(s)

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:27:0C:27:3F:00

Part Number : 73-10918-04

PCA Assembly Number : 800-28909-04

PCA Revision Number : A0

PCB Serial Number : FOC13430YBS

Top Assembly Part Number : 800-29338-04

Top Assembly Serial Number : FCW1346W00Q

Top Revision Number : F0

Product/Model Number : AIR-LAP1522AG-E-K9

% Please define a domain-name first.

flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.

Press RETURN to get started!

Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)

*Mar 1 00:00:07.231: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed

*Mar 1 00:00:07.575: m8349_ether_enable: MACCFG1 sync timeout

*Mar 1 00:00:08.079: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0

*Mar 1 00:00:08.579: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1

*Mar 1 00:00:08.655: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 1297 messages)

*Mar 1 00:00:08.683: AP identified to be in Huck Jr/1240/1130 configuration

*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface Ethernet4, changed state to up

*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up

*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet1, changed state to up

*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet2, changed state to up

*Mar 1 00:00:09.615: %LINK-3-UPDOWN: Interface GigabitEthernet3, changed state to up

*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down

*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1, changed state to down

*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2, changed state to down

*Mar 1 00:00:10.667: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet3, changed state to down

*Mar 1 00:00:10.695: %SYS-5-RESTART: System restarted --

Cisco IOS Software, C1520 Software (C1520-K9W8-M), Version 12.4(21a)JHB, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Compiled Tue 06-Jul-10 14:49 by prod_rel_team

*Mar 1 00:00:10.695: %SNMP-5-COLDSTART: SNMP agent on host wifikal.Laiki-agora is undergoing a cold start

*Mar 1 00:00:10.759: Warning: Failed to run startup script

*Mar 1 00:00:10.771: %MESH-6-BVI_CREATED: Mesh BVI1 interface created

*Mar 1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset

*Mar 1 00:00:10.791: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset

*Mar 1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down

*Mar 1 00:00:11.791: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down

*Mar 1 00:00:12.771: %LINK-3-UPDOWN: Interface BVI1, changed state to down

*Mar 1 00:00:18.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up

*Mar 1 00:00:20.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up

Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)

*Mar 1 00:00:22.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER

flash:/mesh_start_cfg.txt: No such file or directoryThe filesystem containing the variables may not be initialized yet.

*Mar 1 00:00:25.771: No Mesh startup file found

*Mar 1 00:00:29.763: Logging LWAPP message to 0.0.0.0.

*Mar 1 00:00:31.787: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER

*Mar 1 00:00:31.787: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Mar 1 00:00:31.987: %SSH-5-ENABLED: SSH 2.0 has been enabled

*Mar 1 00:00:45.355: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC_NO_INJECTOR_CONFIGURED WS-C2960-8TC-L (0025.b413.b802)

*Mar 1 00:00:45.355: -Verify the required power-injector is installed on this port: WS-C2960-8TC-L(Fas 0/2).

*Mar 1 00:00:45.355: -If a power-injector is installed, issue the command:"power inline negotiation injector installed"

*Mar 1 00:01:26.015: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started

*Mar 1 00:01:34.515: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started

*Mar 1 00:01:36.515: %LINK-3-UPDOWN: Interface BVI1, changed state to up

*Mar 1 00:01:37.515: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up

*Mar 1 00:01:39.563: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

*Mar 1 00:03:05.575: %LWAPP-3-FALLBACK_DHCP: Invalid Static Gateway, so fallback to DHCP.

*Mar 1 00:03:15.583: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started

*Mar 1 00:03:15.703: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 20.20.20.37, mask 255.255.255.0, hostname wifikal.Laiki-agora

*Mar 1 00:03:15.703: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started

*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Invalid event 29 & state 4 combination.

*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message.

*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to handle timer message.

*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Failed to process timer message.

*Mar 1 00:03:17.583: %CAPWAP-3-ERRORLOG: Discovery interval timer expiry handler failed.

Translating "CISCO-CAPWAP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)

*Mar 1 00:03:20.751: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY

Translating "CISCO-LWAPP-CONTROLLER.TelestoHQ"...domain server (62.169.194.48)

*Mar 1 00:03:21.759: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.

*Mar 1 00:03:21.815: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.TelestoHQ

*Mar 1 00:03:21.871: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER.TelestoHQ

*Mar 1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired

*Mar 1 00:04:37.583: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired

*Mar 1 00:04:37.583: %MESH-6-LINK_UPDOWN: Mesh station 0027.0c27.3ffc link Down

topic Cisco LAP 1522 in Wireless

Cisco LAP 1522

Re: Cisco LAP 1522

Cisco LAP 1522

Re: Cisco LAP 1522

Re: Cisco LAP 1522

Cisco LAP 1522