wlse config templates

diro — Sun, 04 Jul 2021 19:34:55 GMT

When i use config templates in the wlse the job always fails stating that the following command resulted in errors "no dot11 ssid tsunami". I'm running 2.13 on the wlse and this command was not in the template, it is just performed at the of the template. Does anybody have the same problem and is there a solution?

Re: wlse config templates

Scott Fella — Wed, 12 Jul 2006 22:30:35 GMT

Give an example of your template. Did you try to push out a small configuration to see if it works or gives you the same error?

Re: wlse config templates

diro — Thu, 13 Jul 2006 04:51:38 GMT

This is the template, it's all executed,even saved. But at the end i got the config failed with remark "no ssid ..."

version 12.3

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

hostname pod-1-1242-2

enable secret xxxx

username Cisco password xxxx

clock timezone GMT -6

clock summer-time S recurring

ip subnet-zero

ip domain name security.com

ip name-server 10.1.1.2

aaa new-model

aaa group server radius rad_eap

server 10.1.1.2 auth-port 1812 acct-port 1813

aaa group server radius rad_mac

aaa group server radius rad_acct

aaa group server radius rad_admin

aaa group server tacacs+ tac_admin

aaa group server radius rad_pmip

aaa group server radius dummy

aaa authentication login eap_methods group rad_eap

aaa authentication login mac_methods local

aaa authorization exec default local

aaa accounting network acct_methods start-stop group rad_acct

aaa session-id common

power inline negotiation prestandard source

bridge irb

dot11 ssid pod1

authentication open eap eap_methods

authentication network-eap eap_methods

authentication key-management wpa

interface Dot11Radio0

no ip address

no ip route-cache

encryption mode ciphers tkip

ssid pod1

short-slot-time

speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0

power local cck -1

power local ofdm -1

power client 2

channel least-congested 2412 2437 2462

station-role root

no cdp enable

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

no shutdown

interface Dot11Radio1

no ip address

no ip route-cache

encryption mode ciphers tkip

ssid pod1

speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0

power local -1

power client 2

station-role root

no cdp enable

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

bridge-group 1 spanning-disabled

interface FastEthernet0

no ip address

no ip route-cache

duplex auto

speed auto

bridge-group 1

no bridge-group 1 source-learning

bridge-group 1 spanning-disabled

interface BVI1

ip address 10.1.1.13 255.255.255.0

no ip route-cache

ip default-gateway 10.1.1.1

ip http server

no ip http secure-server

ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

ip radius source-interface BVI1

logging snmp-trap emergencies

logging snmp-trap alerts

logging snmp-trap critical

logging snmp-trap errors

logging snmp-trap warnings

snmp-server view iso iso included

snmp-server community public1 view iso RO

snmp-server community pod1 view iso RW

snmp-server chassis-id pod-1-1130-1

snmp-server enable traps tty

radius-server attribute 32 include-in-access-req format %h

radius-server host 10.1.1.2 auth-port 1812 acct-port 1813 key awlat

radius-server vsa send accounting

bridge 1 route ip

wlccp ap username wds1 password xxx

end

Re: wlse config templates

Scott Fella — Thu, 13 Jul 2006 09:34:41 GMT

If you are trying to configure a new ap why don't you push the config out using the boot file. Also if it is a new ap, you have to use 'NO ....." to remove the default configurations you do not need. After you push this template, and then do a show run.... is there an ssid tsunami?

topic wlse config templates in Wireless

wlse config templates

Re: wlse config templates

Re: wlse config templates

Re: wlse config templates