topic Cisco 9130AXE - how to configure Multiple BSSID? in Wireless

Cisco 9130AXE - how to configure Multiple BSSID?

shlomoi — Tue, 13 Jul 2021 06:27:42 GMT

Hi,

I'm trying to configure Multi BSSID with my Cisco 9130AXE but with no success. It does seem that the feature is supported and configurable but I no success activating it.

Can you please supply detailed information on how to turn MBSSID on?

Thank you!

Re: Cisco 9130AXE - how to configure Multiple BSSID?

Rps-Cheers — Tue, 13 Jul 2021 10:05:16 GMT

Basic service set identifiers (BSSID) is used to describe sections of a wireless local area network or WLAN.

According to what you mean, can I understand that multiple SSIDs need to be configured?

Catalyst9130 AP can run EWC mode, which is like Mobility Express. You can config the multi SSID refer to the doc, it's a very nice guide for EWC.

Cisco Embedded Wireless Controller on Catalyst Access Points

Re: Cisco 9130AXE - how to configure Multiple BSSID?

shlomoi — Tue, 13 Jul 2021 10:32:36 GMT

Hi,

I'm referring to Multiple BSSID which is part of 11AX new features.

I can see the configuration here:

But after enabling it, each SSID transmit it's own beacon. Therefore I still think there is something I am missing in the configuration.

Can you please share some details on how to configure 11AX Multiple BSSID? Is this feature fully supported? Maybe a firmware version update is require?

Thank You!

Re: Cisco 9130AXE - how to configure Multiple BSSID?

Rps-Cheers — Tue, 13 Jul 2021 14:16:53 GMT

The Multiple BSSID element collapses information for multiple BSSIDs (= SSIDs) into one single beacon frame
If not otherwise needed, this avoids sending the same information elements (e.g. EDCA parameter set etc.) several times

But in the configuration document, only the following configuration. And it seems that the configuration is turned on by default, and no more clear instructions have been found.

Procedure

Step 1

Choose Configuration > Radio Configurations > High Throughput.

Step 2

Click the 5 GHz Band tab.

Expand the 11ax section.
Select the Enable 11ax and Multiple Bssid check boxes, if required.
Check either the Select All check box to configure all the data rates or select the desired options from the available data rates list.

Step 3

Click the 2.4 GHz Band tab.

Expand the 11ax section.
Select the Enable 11ax and Multiple Bssid check boxes, if required.
Check either the Select All check box to configure all the data rates or select the desired options from the available data rates list.

Re: Cisco 9130AXE - how to configure Multiple BSSID?

00u17hj1ymKZeVoUd5d7 — Wed, 14 Jul 2021 09:44:09 GMT

Hi,

Yes, that's exactly what I did. All the above was enabled. Also enabled couple of WLANs (different SSID , BSSIDs...). And there were no Multiple BSSID. Each BSSID transmitted it's own beacon.

Re: Cisco 9130AXE - how to configure Multiple BSSID?

patoberli — Wed, 14 Jul 2021 15:54:13 GMT

This would break support for 802.11ac/n/g/b/a. Do you really want that?

If yes, is your sniffer actually capable of also sniffing those new ones?

And lastly, I'm not sure if that function would disable the old beacons and replace it with the new beacon, or if starts to send out an additional beacon with all the BSSIDs included for compatibility reasons with the old chipsets.

Re: Cisco 9130AXE - how to configure Multiple BSSID?

shlomoi — Thu, 15 Jul 2021 11:30:59 GMT

This does not break 11ac,b,g,n,a...

Are you familiar with the BSSID feature? it is a new feature mandatory in 11ax.

Re: Cisco 9130AXE - how to configure Multiple BSSID?

patoberli — Thu, 15 Jul 2021 12:47:36 GMT

No not really familiar with Multi-BSSID it yet. But the few lines I read sounded like breaking the old standards (if you remove those Beacons, those clients can't anymore connect).
Found this document: https://mentor.ieee.org/802.11/dcn/15/11-15-1014-00-00ax-multiple-bssid-element.pptx
If I understand it correct, it's basically 802.11v-2011, which as far as I know is already supported on the WLC since many years. I also have that enabled since years with no problems in my BYOD environment. Though, by looking at the options on my WLC 8.10, nothing sounds like Multiple-BSSID of the 802.11v features.

Re: Cisco 9130AXE - how to configure Multiple BSSID?

shlomoi — Mon, 19 Jul 2021 08:41:22 GMT

Does anyone from Cisco knows how to configure this feature?

It doesn't seem to be working when enabling it in the GUI

Re: Cisco 9130AXE - how to configure Multiple BSSID?

patoberli — Mon, 19 Jul 2021 09:37:58 GMT

Cisco is not very active in this forum, it's better if you open a TAC for this.

Re: Cisco 9130AXE - how to configure Multiple BSSID?

shlomoi — Tue, 20 Jul 2021 06:41:08 GMT

Thank you!

I will try to do that.