iPhone 12 Pro Max with iOS 14.5 Disconnection Issue

davidlic — Sun, 01 Aug 2021 08:03:36 GMT

I have Wireless network with AIR-AP1832 APs and CT-3504 controller (OS Ver.: 8.10.130.0). All is working fine except iPhone 12 Pro Max with iOS 14.5.1, which disconnects from network frequently.

Can anyone help in this regard? WLC Config is attached

Re: iPhone 12 Pro Max with iOS 14.5 Disconnection Issue

Leo Laohoo — Sun, 01 Aug 2021 08:32:48 GMT

What does the debug say?

Re: iPhone 12 Pro Max with iOS 14.5 Disconnection Issue

Mark Elsen — Sun, 01 Aug 2021 09:50:49 GMT

- Have the controller-config , as you posted in attachment, analyzed with : https://cway.cisco.com/tools/WirelessAnalyzer/

(I will attach the controller and ap part in the next section of this answer) , you can also do client debugging with : https://cway.cisco.com/tools/WirelessDebugAnalyzer/

Here's the result from your attachment (from : https://cway.cisco.com/tools/WirelessAnalyzer/ ) - rerun to get complete reports , you will also then get the color indicators indicating severity.

Emesys-WLC

Level	Message
30122	RLDP: RLDP is enabled for all AP types. This may have severe impact on voice applications, and lower performance for general data. It is advisable to use the option of monitor mode Aps if this is a security requirement, or disable it Action: RLDP should be configured to use only Monnitor mode APs, please check your WPS configuration. This may have severe impact on performance
30012	AP Manager: AP manager interfaces count less than number of active ports, and no LAG, not supported configuration Action: For non LAG scenarios, all active physical ports should have a AP manager interface associated, otherwise there can be traffic issues, or CAPWAP errors. Check active port assignment on the interfaces
120003	Security: It is recommended to monitor all channels for rogue detection. Band(s): 2.4GHz,5GHz Action: None
30071	Fast SSID: Fast SSID enabled is recommended for networks that may have Apple IOS client devices Action: Fast SSID allows easier client jump between WLANS, and it is highly recommended for networks with Apple devices. It should not be used in combination with NAC policies. Command: config network fast-ssid-change enable
30076	NTP: Controller without time source, please configure a valid NTP server Action: No time source detected for this controller. It could be incomplete configuration, check that NTP servers are configured. Command: config time ntp server
30077	Security: Controller with telnet enabled, this is not advisable from security point of view Action: For security reasons, it is not recommended to use Telnet for CLI access to the controller, use SSH instead
30112	Multicast: The IPv6 Multicast/Broadcast mode is on Unicast. Action: For performance optimizations, it is recommended to use multicast transport mode. Please enable in general multicast settings
30119	NTP: NTP Polling Interval is set, but no NTP Server is configured. Controller should have time source Action: Please check the NTP time sync status, as having a proper time source is critical for several features
120001	Security: It is recommended to disable Management over wireless, if the feature is needed, ensure you have a proper CPU ACL Action: In Config/network, you can enable/disable this feature. Use only when needed
120004	Security: No WLAN with WPA2/802.1x was detected, it is recommended to use proper authentication for security reasons. This may not be applicable on some deployment models Action: It is expected to see at least one network with L2 security policies enable. This is just a general check to confirm if this is a status done intentionally
120009	Security: No CPU ACL detected, it is recommended it, to restrict management access to the controller Action: In some scenarios, a CPU ACL can be set to improve security. This may need testing, so use with care
120014	Security: The following Management Password policies are not enabled: Position Check,Case Digit Check Action: This is optional security best practice
120015	Security: HTTP access to management is enabled, it is recommended to only allow https for security reasons Action: This is optional security best practice
60020	RF: WLC has 12.5% of APs with failed Interference Profile for 2.4GHz Band Action: None
30097	RRM: TPC is not set to Auto. For general deployments it is recommended to use RRM. Band(s): 2.4 GHz,5 GHz Action: None
30057	RF: Legacy rate in Global in use. Disabling low data rates/11b can help to optimise the channel utilisation on the 2.4 band. Depending on RF coverage, or if using legacy clients, this may cause problems. Please validate before enforcing the changes, as this may have important RF dependencies. Action: In most scenarios, it is good idea to disable 11b data rates (1,2,5.5,11), as they would use more RF time, and be more sensible to interference, it is advisable to only enable 11g rates, unless you need to support legacy devices. Command:config 802.11b rate disabled X
30064	Authentication: EAPoL request timeout larger than 400 ms. EAP key requests may benefit for faster recovery, and better behavior on bad RF, by using higher counts, lower retry timeout. Please validate on your specific client types before enforcing the changes Action: EAPoL request timer found to be higher than 400ms. In most scenarios, 400 would allow faster recovery in case of problems. Some devices may need longer timers, so always check. Use command: config advanced eap eapol-key-timeout, to adjust
30067	Rogue Detection: Minimum Rogue RSSI detection threshold should be set to -80 or higher, unless mandated by your security policies Action: Min RSSI feature allows to filter out unwanted rogues from the network (out of building). It is advisable to use -70 to -80 depending on your physical location and security policies. Command: config rogue detection min-rssi
30083	High Availability: High Availability is a recommended redundancy solution for supported platforms Action: This is general recommendation to use HA feature when possible, to improve network reliability
30084	Webauth: Virtual Gateway IP is not on 192.0.2.0/24 , 198.51.100.0/24 , 203.0.113.0/24 networks, change to recommended to avoid overlapping with Internet Allocated addresses. RFC5737 Action: Virtual GW address must not match any Internet Routable address, as it could lead to controller absorving traffic for it. Use one of the recommended addresses
30111	DHCP: It is recommended to have the DHCP proxy enabled. Action: This is purely a general recommendation, please validate if applicable in your environment
30081	Load Balancing: Enterprise: Aggressive Load Balancing is a recommended best practice for enterprise environments with proper AP density, for local mode APs. Do not use for WLANs with interactive applications (voice/video) Action: Load Balancing could help on load distribution on some scenarios, it must be avoided for networks with interactive traffic like voice or video. Command: config wlan load-balance allow enable ID
30082	Client Profiling: Local Profiling is a recommended best practice for better client visibility Action: Local profiling is recommended in general, unless using NAC profiling. To enable: config wlan profiling local all enable ID
30130	Security: WLC is not vulnerable to CVE-2017-13082 802.11r/FT Action: Informational message about vulnerability exposure
30125	WLAN: Disabled WLAN, no checks run. WLAN(s): Senior Officer Action: None

Level	Message
20024	WCAE: Missing configuration. APS: MConf-Room Action: This is indication of incomplete or corrupted config file. Try to capture using transfer upload command
20017	Syslog: Syslog to broadcast. APS: More than 10 APs affected, use standalone tool for more details Action: AP syslog is set to broadcast destination (default). It is recommended to configure unicast server, for security and ease of troubleshooting. Command: config ap syslog host global
60029	RF: AP shows low coverage (all neighbors < -75 dBm) on 5GHz band. This could affect roaming and be indication of poor RF design or NDP issues. APS: AP-ROOM-205-CORRIDOR Action: None
20007	CAPWAP: Invalid primary switch config. APS: More than 10 APs affected, use standalone tool for more details Action: The AP has configured a controller name which is not present in the analyzed config file. This may also indicate an error in the AP configuration.
20028	RRM: Assigned channel not in DCA list. APS: AP-Research-Room-02,AP-SECTT-1 Action: Current assigned channel is not on the DCA list, this could cause problems on roaming or reaction to DFS events. It is recommended to match the DCA channel list to the AP assigned channels
60030	RF: AP has asymmetric nearby between radios, if the antennas per band are the same, this could indicate a radio hang . APS: AP-Room-88 Action: For non DFS channels, if the antennas are same between both radios, if the AP has neighbors better than -77 in one radio, and none in the other, this could be indication of radio hang, and should be investigated
60027	RF: AP is isolated (no neighbors) on 5GHz band. This could be expected on single AP scenarios, but could be indication of poor RF design or NDP issues. APS: AP-Room-88 Action: None
30050	High Density: RX-SOP in use. APS: More than 10 APs affected, use standalone tool for more details Action: This is informational message, no action required, if this was changed intentionally
60013	RF: AP side channel interference above threshold. APS: More than 10 APs affected, use standalone tool for more details Action: None
60011	RF: AP Cochannel interference above threshold, 2.4 GHz Band. APS: AP-Room-88,AP-Room-274,AP-Room-213 Action: None
60005	RF: Interference Profile Failed, 2.4GHz Band. APS: AP-Room-213,AP-ROOM-265,AP-Room-114,AP-CT-1Flr-Room-10,AP-Room-261 Action: None
20032	Rogue Containment: AP used for Containment . APS: AP-ROOM-205-CORRIDOR Action: AP has been used for containment. This is a security feature, but its usage on client serving AP have severe impact on WLAN service availability. If containment is required, use dedicated APs to lower network impact
60012	RF: AP Cochannel interference above threshold, 5 GHz Band. APS: More than 10 APs affected, use standalone tool for more details Action: None
60014	RF: AP high channel utilization. Band 2.4GHz. APS: AP-CT-1Flr-Room-12 Action: None

Re: iPhone 12 Pro Max with iOS 14.5 Disconnection Issue

Arshad Safrulla — Sun, 01 Aug 2021 12:47:29 GMT

Any specific reason that you have multiple country codes(AR,BD,GB,MY,PK) and AP's from multiple regulatory domains (C,A & H)?

Also did you do a RF survey at the site? Most of your AP's are in UNII-3 excluding 2 AP's and and 1 AP has it's 5GHz radio disabled. So it is recommended that you do a RF survey and I can see AP's from multiple regulatory domain are RF neighbors. So depending on the country you have deployed this setup you may be violating your regulatory set rules.

topic iPhone 12 Pro Max with iOS 14.5 Disconnection Issue in Wireless

iPhone 12 Pro Max with iOS 14.5 Disconnection Issue

Re: iPhone 12 Pro Max with iOS 14.5 Disconnection Issue

Re: iPhone 12 Pro Max with iOS 14.5 Disconnection Issue

WLC Messages

Emesys-WLC

AP Message Summary

Re: iPhone 12 Pro Max with iOS 14.5 Disconnection Issue