Access Point (u-boot>) not is working

nstr1 — Tue, 21 Sep 2021 20:03:28 GMT

Not working my access point 9115.

I have an access point and it show;

Mounting UBI device fs
ubi0: attaching mtd3
ubi0: scanning is finished
ubi0: attached mtd3 (name "mtd=2", size 1017 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 4063, bad PEBs: 6, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 839138221
ubi0: available PEBs: 33, total reserved PEBs: 4030, PEBs reserved for bad PEB handling: 74
Load Addr 0x10000000
Mount UBIFS PARTITION part2 ...
Loading file 'part2/part.bin' to addr 0x10000000...
Done

Checking image signing.
Image signing verification success for part part2 continue to run...
Multi Image Header Found
Count = 0 Offset = 0x10000050 Len = 10985760
Count = 1 Offset = 0x10a7a170 Len = 3065172
Count = 2 Offset = 0x10d666c4 Len = 7202
Booting from Partition: part2
arg 0: 0x10000050
arg 1: 0x3000000
arg 2: 0x1800000
## Loading init Ramdisk from Legacy Image at 03000000 ...
Image Name: Simple Ramdisk Image
Created: 2021-03-03 8:29:59 UTC
Image Type: AArch64 Linux RAMDisk Image (lzma compressed)
Data Size: 3065108 Bytes = 2.9 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 01800000
Booting using the fdt blob at 0x1800000
load dtb from fixed memory location directly...
/memory = 0x80000000 bytes @ 0x0
Set Memory to 2147483648l
WARNING: Node's property /reserved-memory/dt_reserved_buffer is not defined
WARNING: Node's property /reserved-memory/dt_reserved_flow is not defined
Appending NVRAM to dtb, ret:0
Loaded DTB from 0x01800000 with size 7202l
Curr Boot Args: <NULL>
DTB Boot Args (coherent_pool=4M cpuidle_sysfs_switch pci=pcie_bus_safe rootwait crashkernel=128M@0M)
Bootargs set to setenv bootargs console=$consoledev,$baudrate activepart=part2 activeboot=0 bootver=0x44 boardid=0x1 forceboot=0 coherent_pool=4M cpuidle_sysfs_switch pci=pcie_bus_safe rootwait crashkernel=128M@0M $console $nandEcc $mtdparts ubi.mtd=fs BOOT_DEBUG=0
Cleanup Complete.... ARMv8_secure_init_done!!!
Loading Ramdisk to 4fbba000, end 4fea6514 ... OK
reserving fdt memory region: addr=0 size=20000
Using Device Tree in place at 0000000001800000, end 0000000001804c21

Starting kernel ...

[01/01/1970 00:00:05.0100] hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
[01/01/1970 00:00:05.1020] brcmboard registered
[*01/01/1970 00:00:16.7450] buginf() enabled.
[*01/01/1970 00:00:16.7510] Made it into bootsh: Mar 3 2021 08:06:36 T-0b7bc0faa97ae8a26ea605c7622aac357397184c-g0b7bc0fa-aut
[*01/01/1970 00:00:25.1580] verify signature failed for /bootpart/part2/ramfs_data_cisco.cpio.lzma
[*01/01/1970 00:00:25.1850] Rebooting in 5 seconds ...[01/01/1970 00:00:30.1860] device_shutdown: dev=0xffffffc003a68e20 driver=0xffffffc00094c328 shutdown=0xffffffc000384f80
[01/01/1970 00:00:30.3060] device_shutdown: dev=0xffffffc029799898 bus=0xffffffc00094b8e8 shutdown=0xffffffc000379258
[01/01/1970 00:00:30.4300] device_shutdown: dev=0xffffffc029799098 bus=0xffffffc00094b8e8 shutdown=0xffffffc000379258
[01/01/1970 00:00:30.5540] device_shutdown: dev=0xffffffc003a68620 driver=0xffffffc00094c328 shutdown=0xffffffc000384f80
[01/01/1970 00:00:30.6810] device_shutdown: dev=0xffffffc029798898 bus=0xffffffc00094b8e8 shutdown=0xffffffc000379258
[01/01/1970 00:00:30.8050] device_shutdown: dev=0xffffffc029798098 bus=0xffffffc00094b8e8 shutdown=0xffffffc000379258
[01/01/1970 00:00:30.9290] device_shutdown: dev=0xffffffc003bd1c20 bus=0xffffffc0009614c0 shutdown=0xffffffc000468578
[01/01/1970 00:00:31.0540] device_shutdown: dev=0xffffffc003bd1a20 bus=0xffffffc0009614c0 shutdown=0xffffffc000468578
[01/01/1970 00:00:31.1780] device_shutdown: dev=0xffffffc003bd1220 bus=0xffffffc0009614c0 shutdown=0xffffffc000468578
[01/01/1970 00:00:31.3020] device_shutdown: dev=0xffffffc003a9b470 bus=0xffffffc0009614c0 shutdown=0xffffffc000468578
[01/01/1970 00:00:31.4260] device_shutdown: dev=0xffffffc07d647e10 driver=0xffffffc0009627f0 shutdown=0xffffffc0003d6ff8
[01/01/1970 00:00:31.5530] device_shutdown: dev=0xffffffc07d646010 driver=0xffffffc0009611d8 shutdown=0xffffffc0003d6ff8
[01/01/1970 00:00:31.6810] device_shutdown: dev=0xffffffc07d5abe10 driver=0xffffffc000961100 shutdown=0xffffffc0003d6ff8
[01/01/1970 00:00:31.8080] reboot: Restarting sÿHELO
5.0205HNDRC1a-1.0.38-163.162
CPU0
L1CD
MMUI
MMUA
CODE
ZBBS
MAIN
Boot Strap Register: 0x6fc3b
NVRAM memcfg 0x41627
DDR3-1600 CL11 total 2048MB 2 16bits part[s] %1 SSC

DDR test done successfully
CFE Version: 5
Verifying MASTER U-Boot...
Launching MASTER U-Boot version 0x0044 ...

____ _
/ ___|(_) ___ ___ ___
| | | |/ __| / __|/ _ \
| |___ | |\__ \| (__| (_) |
\____||_||___/ \___|\___/
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|

U-Boot 2017.09 (Feb 05 2021 - 11:50:07 -0800) Broadcom BCM49408

Board: SS-e
I2C: ready
DRAM: 2 GiB
enable MMU ... OK
NAND: Status wait timeout: nandsts=0x0 mask=0x40000000, count=0
NAND ECC BCH-8, page size 4096 bytes, spare size used 216 bytes
1024 MiB
MMC:
SF: Detected mx25l6405d with page size 256 Bytes, erase size 4 KiB, total 8 MiB
In: serial
Out: serial
Err: serial
Platform: 4908
SF: Detected mx25l6405d with page size 256 Bytes, erase size 4 KiB, total 8 MiB
pmc_init:PMC using DQM mode
pmc_patch_4908:7 0 12b046b 34a0346
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.200
Gateway IP address : 10.1.1.1
Run from flash/host/tftp (f/h/c) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 3
Default host ramdisk file name :
Default ramdisk store address :
Board Id (0-18) : 949408EAP_54991
Number of MAC Addresses (1-32) : 11
Base MAC Address : 84:f1:47:b1:2f:30
PSI Size (1-128) KBytes : 48
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Auxillary File System Size Percent: 0
flow memory allocation (MB) : 43
buffer memory allocation (MB) : 16
DHD 0 memory allocation (MB) : 0
DHD 1 memory allocation (MB) : 0
DHD 2 memory allocation (MB) : 0
Partition 1 Size (MB) : 0M
Partition 2 Size (MB) : 0M
Partition 3 Size (MB) : 0M
Partition 4 Size (MB) (Data) : 4M

BootImage: MASTER
Found external PHY firmware image
MTDPART Str = (mtdparts=nand:1m(nvram),5888k(bootfs),-(fs))
Net: Registering Ethernet Driver.....
Broadcom BCM 4908 Ethernet driver 0.1
pmc_switch_power_up: Rgmii Tx clock zone1 enable 0 zone2 enable 0.
Setting SGMII Calibration value to 0xa
swap_pair = 0

Detecting PHYs...
84880 A0 ae02:5158 --> N/A
84881 A0 ae02:5150 --> N/A
84884 A0 ae02:5148 --> N/A
84884E A0 ae02:5168 --> N/A
84885 A0 ae02:5178 --> N/A
84886 A0 ae02:5170 --> N/A
84887 A0 ae02:5144 --> N/A
84888 A0 ae02:5140 --> N/A
84888E A0 ae02:5160 --> N/A
84888S A0 ae02:5174 --> N/A
84880 B0 ae02:5159 --> N/A
84881 B0 ae02:5151 --> N/A
84884 B0 ae02:5149 --> N/A
84884E B0 ae02:5169 --> N/A
84885 B0 ae02:5179 --> N/A
84886 B0 ae02:5171 --> N/A
84887 B0 ae02:5145 --> N/A
84888 B0 ae02:5141 --> N/A
84888E B0 ae02:5161 --> N/A
84888S B0 ae02:5175 --> N/A
84891 A0 3590:5090 --> N/A
54991 A0 3590:5094 --> N/A
54991E A0 3590:5098 --> N/A
84891L A0 3590:5080 --> N/A
54991L A0 3590:5084 --> N/A
54991EL A0 3590:5088 --> N/A
84892 A0 3590:50a0 --> N/A
54992 A0 3590:50a4 --> N/A
54992E A0 3590:50a8 --> N/A
84894 A0 3590:50b0 --> N/A
54994 A0 3590:50b4 --> N/A
54994E A0 3590:50b8 --> N/A
54991H A0 3590:50d0 --> N/A
54994H A0 3590:50f0 --> N/A
84891 B0 3590:5091 --> N/A
54991 B0 3590:5095 --> N/A
54991E B0 3590:5099 --> N/A
84891L B0 3590:5081 --> N/A
54991L B0 3590:5085 --> N/A
54991EL B0 3590:5089 --> 0x1f
84892 B0 3590:50a1 --> N/A
54992 B0 3590:50a5 --> N/A
54992E B0 3590:50a9 --> N/A
84894 B0 3590:50b1 --> N/A
54994 B0 3590:50b5 --> N/A
54994E B0 3590:50b9 --> N/A
54991H B0 3590:50d1 --> N/A
54994H B0 3590:50f1 --> N/A

Loading firmware into detected phys...
Firmware version: Blackfin B0 v02-02-03-2020-03-16
Loading firmware into phys: map=0x80000000
Halt the phys processors operation
Upload the firmware into the on-chip memory
0% 1% 2% 3% 4% 5% 6% 7% 8% 9% 10% 11% 12% 13% 14% 15% 16% 17% 18% 19% 20% 21% 22% 23% 24% 25% 26% 27% 28% 29% 30% 31% 32% 33% 34% 35% 36% 37% 38% 39% 40% 41% 42% 43% 44% 45% 46% 47% 48% 49% 50% 51% 52% 53% 54% 55% 56% 57% 58% 59% 60% 61% 62% 63% 64% 65% 66% 67% 68% 69% 70% 71% 72% 73% 74% 75% 76% 77% 78% 79% 80% 81% 82% 83% 84% 85% 86% 87% 88% 89% 90% 91% 92% 93% 94% 95% 96% 97% 98% 99% 100%
Reset the processors to start execution of the code in the on-chip memory
Verify that the processors are running: OK
Verify that the firmware has been loaded with good CRC: OK
Firmware loading completed successfully

Unsupported MII type: 0
bcm4908_eth-0
MAC: 84:f1:47:b1:2f:30

Hit ESC key to stop autoboot: 3 2 1 MG link 1G
0
Mounting UBI device fs
ubi0: attaching mtd3
ubi0: scanning is finished
ubi0: attached mtd3 (name "mtd=2", size 1017 MiB)
ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192
ubi0: good PEBs: 4063, bad PEBs: 6, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 839138221
ubi0: available PEBs: 33, total reserved PEBs: 4030, PEBs reserved for bad PEB handling: 74
Load Addr 0x10000000
Mount UBIFS PARTITION part2 ...
Loading file 'part2/part.bin' to addr 0x10000000...
Done

Starting kernel ...

u-boot> help
? - alias for 'help'
base - print or set address offset
bdinfo - print Board Info structure
boardinit- Download MFG boardinit bundle and burn images to its repective location
boot - boot default, i.e., run 'bootcmd'
boot_image- Boot Image
bootd - boot default, i.e., run 'bootcmd'
bootefi - Boots an EFI payload from memory
bootelf - Boot from an ELF image in memory
booti - boot arm64 Linux Image image from memory
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
bubt - Burn image to NOR flash boot device
chpart - change active partition
cisco_booti- Cisco modified boot arm64 Linux Image image from memory.
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
dhcp - boot image via network using DHCP/TFTP protocol
dm - Driver model low level access
echo - echo args to console
editenv - edit environment variable
env - environment handling commands
erase - erase FLASH memory
erase_nvram- Erase NVRAM
erase_persistent_data- Erase Persistent Data
exit - exit script
false - do nothing, unsuccessfully
fdt - flattened device tree utility commands
fipsalgval- run algorithm validation on test vector bibnar in memory, default:2000000 (0x02000000)
flash_image- Flash Image
flinfo - print FLASH memory information
forceboot- force boot from u-boot image
fuse - Fuse sub-system
go - start application at address 'addr'
gpio - Read/Write Gpio Pins
help - print command description/usage
i2c - I2C sub-system
iminfo - print header information for application image
imxtract- extract a part of a multi-image
itest - return true/false on integer compare
ledstate- Set Led State
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loadx - load binary file over serial line (xmodem mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
lzmadec - lzma uncompress a memory region
md - memory display
meminfo - display memory information
mm - memory modify (auto-incrementing address)
mtdparts- define flash/nand partitions
mw - memory write (fill)
nand - NAND sub-system
nandboot- boot Linux from NAND partition
nboot - boot from NAND device
netboot - boot Linux from network using TFTP/bootp
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
pci - list and access PCI Configuration Space
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
pxe - commands to get and boot from pxe files
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setboardparms- Set Board Params
setbootline- Set Boot Params
setenv - set environment variables
setexpr - set environment variable as the result of eval expression
sf - SPI flash sub-system
showvar - print local hushshell variables
sleep - delay execution for some time
source - run script from memory
sspi - SPI utility command
sysboot - command to get and boot from syslinux files
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
true - do nothing, successfully
ubi - ubi commands
ubifsload- load file from an UBIFS filesystem
ubifsls - list files in a directory
ubifsmount- mount UBIFS volume
ubifsumount- unmount UBIFS volume
usb - USB sub-system
usbboot - boot from USB device
version - print monitor, compiler and linker version
u-boot>
? - alias for 'help'
base - print or set address offset
bdinfo - print Board Info structure
boardinit- Download MFG boardinit bundle and burn images to its repective location
boot - boot default, i.e., run 'bootcmd'
boot_image- Boot Image
bootd - boot default, i.e., run 'bootcmd'
bootefi - Boots an EFI payload from memory
bootelf - Boot from an ELF image in memory
booti - boot arm64 Linux Image image from memory
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
bootvx - Boot vxWorks from an ELF image
bubt - Burn image to NOR flash boot device
chpart - change active partition
cisco_booti- Cisco modified boot arm64 Linux Image image from memory.
cmp - memory compare
coninfo - print console devices and information
cp - memory copy
crc32 - checksum calculation
dhcp - boot image via network using DHCP/TFTP protocol
dm - Driver model low level access
echo - echo args to console
editenv - edit environment variable
env - environment handling commands
erase - erase FLASH memory
erase_nvram- Erase NVRAM
erase_persistent_data- Erase Persistent Data
exit - exit script
false - do nothing, unsuccessfully
fdt - flattened device tree utility commands
fipsalgval- run algorithm validation on test vector bibnar in memory, default:2000000 (0x02000000)
flash_image- Flash Image
flinfo - print FLASH memory information
forceboot- force boot from u-boot image
fuse - Fuse sub-system
go - start application at address 'addr'
gpio - Read/Write Gpio Pins
help - print command description/usage
i2c - I2C sub-system
iminfo - print header information for application image
imxtract- extract a part of a multi-image
itest - return true/false on integer compare
ledstate- Set Led State
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loadx - load binary file over serial line (xmodem mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
lzmadec - lzma uncompress a memory region
md - memory display
meminfo - display memory information
mm - memory modify (auto-incrementing address)
mtdparts- define flash/nand partitions
mw - memory write (fill)
nand - NAND sub-system
nandboot- boot Linux from NAND partition
nboot - boot from NAND device
netboot - boot Linux from network using TFTP/bootp
nfs - boot image via network using NFS protocol
nm - memory modify (constant address)
pci - list and access PCI Configuration Space
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
protect - enable or disable FLASH write protection
pxe - commands to get and boot from pxe files
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setboardparms- Set Board Params
setbootline- Set Boot Params
setenv - set environment variables
setexpr - set environment variable as the result of eval expression
sf - SPI flash sub-system
showvar - print local hushshell variables
sleep - delay execution for some time
source - run script from memory
sspi - SPI utility command
sysboot - command to get and boot from syslinux files
test - minimal test like /bin/sh
tftpboot- boot image via network using TFTP protocol
true - do nothing, successfully
ubi - ubi commands
ubifsload- load file from an UBIFS filesystem
ubifsls - list files in a directory
ubifsmount- mount UBIFS volume
ubifsumount- unmount UBIFS volume
usb - USB sub-system
usbboot - boot from USB device

How i can configure an ip to my access point and load the image ??????????????

Re: Access Point (u-boot>) not is working

jagan.chowdam — Tue, 21 Sep 2021 20:38:57 GMT

Booting from Partition: part2

AP booting from Partiton 2. Have you tried the following commands ?

setshenv BOOT part1

saveshenv

If the above commands do not work, then use "setenv" and "saveenv".

Once you apply the commands, paste the boot log.

Regards,

Please rate all useful responses

Re: Access Point (u-boot>) not is working

nstr1 — Wed, 22 Sep 2021 14:56:21 GMT

i used the following guide,
but now i don't know how execute the OS.

U-Boot> setenv ipaddr 192.168.2.2

U-Boot> setenv serverip 192.168.2.1

U-Boot> ping 192.168.2.1

macb0: link up, 100Mbps full-duplex (lpa: 0x45e1)

Using macb0 device

host 192.168.2.1 is alive

and copy the OS to the AP

U-Boot> tftp ${loadaddr} (here name OS AP)

macb0: link up, 100Mbps full-duplex (lpa: 0x45e1)

Using macb0 device

TFTP from server 192.168.2.1; our IP address is 192.168.2.2

Filename 'uImage-2.6.30'.

Load address: 0x70000000

Loading: ################################################################# ################################################################# ################################################################# ################################################################# ############################

Re: Access Point (u-boot>) not is working

Sandeep Choudhary — Thu, 23 Sep 2021 05:16:02 GMT

Hi,

Check this post:

https://lihaifeng.net/?p=222

if still doesnt work then Contact Cisco TAC.

Regards

Dont forget to arte helpful posts

topic Re: Access Point (u-boot>) not is working in Wireless

Access Point (u-boot>) not is working

Re: Access Point (u-boot>) not is working

Re: Access Point (u-boot>) not is working

Re: Access Point (u-boot>) not is working