topic AIRONET1852i do not boot in Wireless

topic AIRONET1852i do not boot in Wireless https://community.cisco.com/t5/wireless/aironet1852i-do-not-boot/m-p/4531922#M237126 <P>This host will write console data.</P><P> </P><P>::::</P><P>(RNAQ-C7) # reset</P><P>resetting ...</P><P><SPAN>(cut)</SPAN></P><P>Valid I2C chip addresses: 51 52</P><P>AP 1832/1852 detected...</P><P>Power Type: 802.3af POE or Others detected...</P><P>Signature returns 0</P><P>BL signing verification success, continue to run... </P><P>Auto boot mode, use bootipq directly</P><P>Hit ESC key to stop autoboot:  0 </P><P>Specified BOOT: part1 </P><P>nand0: partition (fs) size alignment incorrect</P><P>Error initializing mtdparts!</P><P> </P><P>Booting from part1</P><P> </P><P>nand0: partition (fs) size alignment incorrect</P><P>Error initializing mtdparts!</P><P>nand0: partition (fs) size alignment incorrect</P><P>Error initializing mtdparts!</P><P> </P><P>Booting failed, try boot on part2</P><P> </P><P>nand0: partition (fs) size alignment incorrect</P><P>Error initializing mtdparts!</P><P>nand0: partition (fs) size alignment incorrect</P><P>Error initializing mtdparts!</P><P>(RNAQ-C7) # </P><P> </P><P>::::</P><P> </P><P>This host can be booted from a tftp image．</P><P> </P><P>::::</P><P> (RNAQ-C7) # bootipq tftp</P><P>Specified BOOT: part1 </P><P>（cut）</P><P>Starting image ...</P><P>::::   </P><P> </P><P>But, This host will not be able to boot if the power is removed and then turned on again.</P><P> </P><P>Help me, please.</P> Sat, 15 Jan 2022 05:37:01 GMT apple_toin_ipad 2022-01-15T05:37:01Z AIRONET1852i do not boot https://community.cisco.com/t5/wireless/aironet1852i-do-not-boot/m-p/4531922#M237126 <P>This host will write console data.</P><P> </P><P>::::</P><P>(RNAQ-C7) # reset</P><P>resetting ...</P><P><SPAN>(cut)</SPAN></P><P>Valid I2C chip addresses: 51 52</P><P>AP 1832/1852 detected...</P><P>Power Type: 802.3af POE or Others detected...</P><P>Signature returns 0</P><P>BL signing verification success, continue to run... </P><P>Auto boot mode, use bootipq directly</P><P>Hit ESC key to stop autoboot:  0 </P><P>Specified BOOT: part1 </P><P>nand0: partition (fs) size alignment incorrect</P><P>Error initializing mtdparts!</P><P> </P><P>Booting from part1</P><P> </P><P>nand0: partition (fs) size alignment incorrect</P><P>Error initializing mtdparts!</P><P>nand0: partition (fs) size alignment incorrect</P><P>Error initializing mtdparts!</P><P> </P><P>Booting failed, try boot on part2</P><P> </P><P>nand0: partition (fs) size alignment incorrect</P><P>Error initializing mtdparts!</P><P>nand0: partition (fs) size alignment incorrect</P><P>Error initializing mtdparts!</P><P>(RNAQ-C7) # </P><P> </P><P>::::</P><P> </P><P>This host can be booted from a tftp image．</P><P> </P><P>::::</P><P> (RNAQ-C7) # bootipq tftp</P><P>Specified BOOT: part1 </P><P>（cut）</P><P>Starting image ...</P><P>::::   </P><P> </P><P>But, This host will not be able to boot if the power is removed and then turned on again.</P><P> </P><P>Help me, please.</P> Sat, 15 Jan 2022 05:37:01 GMT https://community.cisco.com/t5/wireless/aironet1852i-do-not-boot/m-p/4531922#M237126 apple_toin_ipad 2022-01-15T05:37:01Z Re: AIRONET1852i do not boot https://community.cisco.com/t5/wireless/aironet1852i-do-not-boot/m-p/4531923#M237127 <P>Contact Cisco TAC and organize an RMA.</P> Sat, 15 Jan 2022 05:57:12 GMT https://community.cisco.com/t5/wireless/aironet1852i-do-not-boot/m-p/4531923#M237127 Leo Laohoo 2022-01-15T05:57:12Z