https://community.cisco.com/t5/wireless/1832i-get-problem/m-p/4701268#M246972 <P>This need to replace. Open a TAC and request for RMA</P> Tue, 11 Oct 2022 12:23:29 GMT Kasun Bandara 2022-10-11T12:23:29Z https://community.cisco.com/t5/wireless/1832i-get-problem/m-p/4701224#M246967 <P>hello,</P><P>i get the problem my AIR-AP1832I-C-K9 , how can this problem solve please help me. please tell me details .</P><P>thanks you.</P><P>&nbsp;</P><P>(RNAQ-C7) # reset<BR />resetting ...</P><P><BR />U-Boot 2012.07 (btldr release 38) (Oct 29 2019 - 06:39:45)</P><P>This product contains some software licensed under the<BR />"GNU General Public License, version 2" provided with<BR />ABSOLUTELY NO WARRANTY under the terms of<BR />"GNU General Public License, version 2", available here:<BR /><A href="http://www.gnu.org/licenses/old-licenses/gpl-2.0.html" target="_blank" rel="noopener">http://www.gnu.org/licenses/old-licenses/gpl-2.0.html</A></P><P>DRAM: 1 GiB<BR />NAND (ONFI): Detected SPANSION S34MS02G2 [256 MiB]<BR />SF: Detected Macronix MX25U3235F [4 MiB]<BR />MFG data loaded<BR />Scanning shenv data blocks<BR />Total valid parts=4<BR />Active shenv part[1:1], write_counter=12<BR />PCI0 Link Intialized<BR />PCI1 Link Intialized<BR />Net:<BR />PHY ID = 0x4dd074, eth0 found AR8033 PHY<BR />PHY ID = 0x4dd074, eth1 found AR8033 PHY<BR />Valid I2C chip addresses: 51 52<BR />AP 1832/1852 detected...<BR />Power Type: 802.3at POE detected...<BR />Signature returns 0<BR />BL signing verification success, continue to run...<BR />Auto boot mode, use bootipq directly<BR />Hit ESC key to stop autoboot: 0<BR />Specified BOOT: 2<BR />UBI error: ubi_io_read: error -74 while reading 118784 bytes from PEB 1507:4096, read 28672 bytes<BR />ubi_io_read[188] not here<BR />UBI error: ubi_init: cannot attach mtd2<BR />UBI error: ubi_init: UBI error: cannot initialize UBI, error -74<BR />UBI init error 74</P><P>Booting from part1</P><P>Error, no UBI device/partition selected!<BR />Error, no UBI device/partition selected!</P><P>Booting failed, try boot on part2</P><P>Error, no UBI device/partition selected!<BR />Error, no UBI device/partition selected!<BR />(RNAQ-C7) #</P> Tue, 11 Oct 2022 11:19:26 GMT https://community.cisco.com/t5/wireless/1832i-get-problem/m-p/4701224#M246967 Rofiqul7343 2022-10-11T11:19:26Z https://community.cisco.com/t5/wireless/1832i-get-problem/m-p/4701268#M246972 <P>This need to replace. Open a TAC and request for RMA</P> Tue, 11 Oct 2022 12:23:29 GMT https://community.cisco.com/t5/wireless/1832i-get-problem/m-p/4701268#M246972 Kasun Bandara 2022-10-11T12:23:29Z https://community.cisco.com/t5/wireless/1832i-get-problem/m-p/4701577#M247002 <P>RMA the AP.</P> Tue, 11 Oct 2022 23:24:13 GMT https://community.cisco.com/t5/wireless/1832i-get-problem/m-p/4701577#M247002 Leo Laohoo 2022-10-11T23:24:13Z