topic Access Point not join WLC in Wireless

Access Point not join WLC

Nicolasigl — Mon, 28 Nov 2022 12:18:17 GMT

I have a problem with most AIR-AP1832I-A-K9 model access points.

This is the error message displayed in the terminal.

This AP model supports driver version newer than 7.0.0.0!

The WLC software version ---- 8.3.122.0

This access point was working until yesterday

I wait for answers, thanks

Re: Access Point not join WLC

Scott Fella — Mon, 28 Nov 2022 14:50:05 GMT

Search the forum for more threads on this. Looks like you need to upgrade. Here is a few you can review:

1852 AP Unable to join controller - Cisco Community

Solved: C1852 Access Point Unable to Join Controller C5508 - Cisco Community

Re: Access Point not join WLC

Leo Laohoo — Mon, 28 Nov 2022 23:58:34 GMT

Console into the AP and reboot.
Post the entire boot-up process.

Re: Access Point not join WLC

Rich R — Tue, 29 Nov 2022 08:46:15 GMT

What model of WLC?
If you insist on running old software version like 8.3 at least get the last version of it - 8.3.150.0.
Ideally upgrade to latest 8.5 at least as per TAC recommended link below (if your APs and WLC are supported).

AIR-AP1832I-A-K9 - L2 Error Detected!

Nicolasigl — Fri, 16 Dec 2022 11:53:31 GMT

Here is the complete boot capture:

Welcome to Cisco.

Usage of this device is governed by Cisco's End User License Agreement,
available at:
http://www.cisco.com/c/en/us/td/docs/general/warranty/English/EU1KEN_.html.

Restricted Rights Legend

Use, duplication, or disclosure by the Government is subject to
restrictions as set forth in subparagraph (c) of the Commercial
Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

This product contains some software licensed under the
"GNU General Public License, version 2" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html

This product contains some software licensed under the
"GNU Library General Public License, version 2" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Library
General Public License, version 2", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.0.html

This product contains some software licensed under the
"GNU Lesser General Public License, version 2.1" provided
with ABSOLUTELY NO WARRANTY under the terms of "GNU Lesser
General Public License, version 2.1", available here:
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html

This product contains some software licensed under the
"GNU General Public License, version 3" provided with
ABSOLUTELY NO WARRANTY under the terms of
"GNU General Public License, Version 3", available here:
http://www.gnu.org/licenses/gpl.html.

[*01/01/1970 00:00:24.6924] Made it into bootsh: Mar 14 2017 13:10:04
[*01/01/1970 00:00:24.6924] bootsh build T-3bef165fd4988f5ab7c2e5c32b6c5048b7494d95-g3bef165f-kalairam
init started: BusyBox v1.20.2 (2017-03-14 12:40:47 PDT)

User Access Verification
Username: [*01/01/1970 00:00:27.9514] Active version: 8.2.151.0
[*01/01/1970 00:00:27.9614] Backup version: 8.3.122.0
[*01/01/1970 00:00:28.1114] AP1852I
[*01/01/1970 00:00:28.2113] nss_driver - Turbo Support 1
[*01/01/1970 00:00:28.2113] Supported Frequencies - 110Mhz 550Mhz 733Mhz
[*01/01/1970 00:00:28.3113]
[*01/01/1970 00:00:28.3113] phy_value=0: org="0x1000" phy_reg="0x1800"
[*01/01/1970 00:00:28.6812] Current value of FACTORY_RESET=0
[*11/27/2017 23:59:59.0000] Last reload time: Nov 19 23:03:35 2022
[*11/19/2022 23:03:35.0000] Setting system time Sat Nov 19 23:03:35 UTC 2022
[*11/19/2022 23:03:35.0899] device wired0 entered promiscuous mode
[*11/19/2022 23:03:35.1699] device wired1 entered promiscuous mode
[*11/19/2022 23:03:35.1699]
[*11/19/2022 23:03:35.1699] phy_value=0: org="0x1800" phy_reg="0x1800"
[*11/19/2022 23:03:35.5198] stile_lm_ft_corsica: module license [11/19/2022 23:03:35.5398] stile module dp init successfully
[11/19/2022 23:03:35.6398] NBAR Label:BLD_MCP_DEV_LATEST_20150424_123021 NBAR VERSION:module build date: Nov 4 2015 at 14:26:22
'Copyright (c) 2014-2015 by cisco Systems, Inc.' taints kernel.
[*11/19/2022 23:03:35.5398] stile_lm_dp_corsica: module license 'Copyright (c) 2014-2015 by cisco Systems, Inc.' taints kernel.
[*11/19/2022 23:03:36.1596] miibus get eec9c000!
[*11/19/2022 23:03:36.1796]
[*11/19/2022 23:03:36.1896] boot 3143 build T-3bef165fd4988f5ab7c2e5c32b6c5048b7494d95-g3bef165f-kalairam board corsica mac 74:86:0B:5A:30:B0
[*11/19/2022 23:03:36.1896] Module: aptrace .text=0xbf000000 data=0xbf00803c bss=0xbf008440
[*11/19/2022 23:03:36.1896] Module: qca_nss_gmac .text=0xbf00f000 data=0xbf015af8 bss=0xbf015fb8
[*11/19/2022 23:03:36.1896] Module: qca_nss_drv .text=0xbf01f000 data=0xbf0367b0 bss=0xbf037560
[*11/19/2022 23:03:36.1896] Module: qca_nss_capwapmgr .text=0xbf053000 data=0xbf056b6c bss=0xbf056cc0
[*11/19/2022 23:03:36.1896] Module: nssmgrctl .text=0xbf05c000 data=0xbf05d728 bss=0xbf05da4c
[*11/19/2022 23:03:36.1896] Module: proclikefs .text=0xbf063000 data= bss=0xbf063b40
[*11/19/2022 23:03:36.1896] Module: stile_lm_ft .text= data= bss=
[*11/19/2022 23:03:36.1896] Module: stile_lm_dp .text= data= bss=
[*11/19/2022 23:03:36.1896] Module: qca_nss_profile_drv .text=0xbf8d3000 data=0xbf8d4324 bss=0xbf8d4498
[*11/19/2022 23:03:36.1896] Module: ssdk_reg .text=0xbf8d9000 data= bss=0xbf8d9838
[*11/19/2022 23:03:36.5195] Last reload reason : 0: unknown
[*11/19/2022 23:03:37.7591] adf: module license 'Proprietary' taints kernel.
[*11/19/2022 23:03:37.7591] asf: module license 'Proprietary' taints kernel.
[*11/19/2022 23:03:37.7691] ath_hal: module license 'Proprietary' taints kernel.
[*11/19/2022 23:03:37.7791] ath_dfs: module license 'Proprietary' taints kernel.
[*11/19/2022 23:03:37.7791] ath_rate_atheros: module license 'Proprietary' taints kernel.
[*11/19/2022 23:03:37.7891] ath_dev: module license 'Proprietary' taints kernel.
[*11/19/2022 23:03:37.8091]
[*11/19/2022 23:03:37.8091] __ol_ath_attach() Allocated scn c3b00480
[*11/19/2022 23:03:37.8291] Chip id: 0x9, chip version: 0x1000000
[*11/19/2022 23:03:37.8291]
[*11/19/2022 23:03:37.8291] Target Version is 1000000
[*11/19/2022 23:03:37.8291]
[*11/19/2022 23:03:37.8291] Flash Download Address c0000
[*11/19/2022 23:03:37.8291] ol_transfer_bin_file: flash data file defined
[*11/19/2022 23:03:37.8291] Cal location [0]: 00000000
[*11/19/2022 23:03:37.8291]
[*11/19/2022 23:03:37.8291] Wifi0 NAND FLASH Select OFFSET 0x1000
[*11/19/2022 23:03:37.8491] qc98xx_verify_checksum: flash checksum passed: 0x25fa
[*11/19/2022 23:03:37.8491] ol_transfer_bin_file 4020: Download Flash data len 12064
[*11/19/2022 23:03:37.8691]
[*11/19/2022 23:03:37.8691] Board data initialized
[*11/19/2022 23:03:37.9091] ol_ath_download_firmware :First OTP download and Execute is good address:0xa000 return param 4660
[*11/19/2022 23:03:37.9091] ol_ath_download_firmware:##Board Id 8 , CHIP Id 1
[*11/19/2022 23:03:37.9091] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=AR900B/hw.2/boardData_AR900B_CUS260_negative_pwr_offset_2G_v2_008.bin
[*11/19/2022 23:03:37.9791]
[*11/19/2022 23:03:37.9791] [Flash] : Ignore Module param
[*11/19/2022 23:03:37.9991] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0
[*11/19/2022 23:03:38.0191] ol_transfer_bin_file: Downloading firmware file: AR900B/hw.2/athwlan.bin
[*11/19/2022 23:03:39.1187] Startup Mode-0 set
[*11/19/2022 23:03:39.1187] HTC Service:0x0300 ep:1 TX flow control disabled
[*11/19/2022 23:03:39.1187] HTC Service:0x0100 ep:2 TX flow control disabled
[*11/19/2022 23:03:39.1187] Firmware_Build_Number:84
[*11/19/2022 23:03:39.1187] host/RAM_fw Build Ver Mismatch: H:0x47, F:0x54 !
[*11/19/2022 23:03:39.1187] num_rf_chain:0x00000004 ht_cap_info:0x0000185b vht_cap_info:0x339a79b2 vht_supp_mcs:0x0000ffea
[*11/19/2022 23:03:39.1187]
[*11/19/2022 23:03:39.1187] RES CFG Support wmi_service_bitmap 9778
[*11/19/2022 23:03:39.1187]
[*11/19/2022 23:03:39.1187] Sending Ext resource cfg: HOST PLATFORM as 0 and fw_feature_bitmap as 10 to TGT
[*11/19/2022 23:03:39.1187] Mesh Supported
[*11/19/2022 23:03:39.1987] wmi_ready_event_rx: WMI UNIFIED READY event
[*11/19/2022 23:03:39.1987] ACS not enabled
[*11/19/2022 23:03:39.1987] ol_ath_thermal_mitigation_attach: --
[*11/19/2022 23:03:39.2087]
[*11/19/2022 23:03:39.2087] __ol_ath_attach() Allocated scn ee500480
[*11/19/2022 23:03:39.2187] Chip id: 0x9, chip version: 0x1000000
[*11/19/2022 23:03:39.2187]
[*11/19/2022 23:03:39.2187] Target Version is 1000000
[*11/19/2022 23:03:39.2187]
[*11/19/2022 23:03:39.2187] Flash Download Address c0000
[*11/19/2022 23:03:39.2187] ol_transfer_bin_file: flash data file defined
[*11/19/2022 23:03:39.2187] Cal location [1]: 00004000
[*11/19/2022 23:03:39.2187]
[*11/19/2022 23:03:39.2187] wifi1 NAND FLASH Select OFFSET 0x5000
[*11/19/2022 23:03:39.2387] qc98xx_verify_checksum: flash checksum passed: 0x8213
[*11/19/2022 23:03:39.2387] ol_transfer_bin_file 4020: Download Flash data len 12064
[*11/19/2022 23:03:39.2587]
[*11/19/2022 23:03:39.2587] Board data initialized
[*11/19/2022 23:03:39.2987] ol_ath_download_firmware :First OTP download and Execute is good address:0x9c00 return param 4660
[*11/19/2022 23:03:39.2987] ol_ath_download_firmware:##Board Id 7 , CHIP Id 1
[*11/19/2022 23:03:39.2987] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=AR900B/hw.2/boardData_AR900B_CUS239_negative_pwr_offset_5G_v2_007.bin
[*11/19/2022 23:03:39.3786]
[*11/19/2022 23:03:39.3786] [Flash] : Ignore Module param
[*11/19/2022 23:03:39.3886] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0
[*11/19/2022 23:03:39.4086] ol_transfer_bin_file: Downloading firmware file: AR900B/hw.2/athwlan.bin
[*11/19/2022 23:03:40.1184] FWLOG: [33477] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 )
[*11/19/2022 23:03:40.1184] FWLOG: [33477] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 )
[*11/19/2022 23:03:40.1184] FWLOG: [33477] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 )
[*11/19/2022 23:03:40.1184] FWLOG: [33477] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 )
[*11/19/2022 23:03:40.5083] Startup Mode-0 set
[*11/19/2022 23:03:40.5083] HTC Service:0x0300 ep:1 TX flow control disabled
[*11/19/2022 23:03:40.5083] HTC Service:0x0100 ep:2 TX flow control disabled
[*11/19/2022 23:03:40.5083] Firmware_Build_Number:84
[*11/19/2022 23:03:40.5083] host/RAM_fw Build Ver Mismatch: H:0x47, F:0x54 !
[*11/19/2022 23:03:40.5083] num_rf_chain:0x00000004 ht_cap_info:0x0000185b vht_cap_info:0x339b79b2 vht_supp_mcs:0x0000ffea
[*11/19/2022 23:03:40.5083]
[*11/19/2022 23:03:40.5083] RES CFG Support wmi_service_bitmap 9778
[*11/19/2022 23:03:40.5083]
[*11/19/2022 23:03:40.5083] Sending Ext resource cfg: HOST PLATFORM as 0 and fw_feature_bitmap as 10 to TGT
[*11/19/2022 23:03:40.5083] Mesh Supported
[*11/19/2022 23:03:42.6976] pid 1451's current affinity mask: 3
[*11/19/2022 23:03:42.6976] pid 1451's new affinity mask: 1
[11/19/2022 23:03:50.5151] L2 Error detected!
[11/19/2022 23:03:50.5151] L2ESR = 0x00010001
[11/19/2022 23:03:50.5151] L2ESYNR0 = 0x1000891d
[11/19/2022 23:03:50.5151] L2ESYNR1 = 0x0245486a
[11/19/2022 23:03:50.5151] L2EAR0 = 0x8261e824
[11/19/2022 23:03:50.5151] L2EAR1 = 0x00000002
[11/19/2022 23:03:50.5151] CPU bitmap = 0x1

Re: AIR-AP1832I-A-K9 - L2 Error Detected!

Leo Laohoo — Fri, 16 Dec 2022 12:42:03 GMT

@Nicolasigl wrote:

[*11/19/2022 23:03:40.5083] host/RAM_fw Build Ver Mismatch: H:0x47, F:0x54 ! [11/19/2022 23:03:50.5151] L2 Error detected! [11/19/2022 23:03:50.5151] L2ESR = 0x00010001 [11/19/2022 23:03:50.5151] L2ESYNR0 = 0x1000891d [11/19/2022 23:03:50.5151] L2ESYNR1 = 0x0245486a [11/19/2022 23:03:50.5151] L2EAR0 = 0x8261e824 [11/19/2022 23:03:50.5151] L2EAR1 = 0x00000002 [11/19/2022 23:03:50.5151] CPU bitmap = 0x1

Contact Cisco TAC and organize an RMA. The AP is dead.

Re: AIR-AP1832I-A-K9 - L2 Error Detected!

balaji.bandi — Fri, 16 Dec 2022 13:05:20 GMT

Agreed Faulty AP, required replacement, if you have contact raise TAC for RMA.

Re: Access Point not join WLC

Nicolasigl — Fri, 16 Dec 2022 13:39:13 GMT

Welcome to Cisco.

Usage of this device is governed by Cisco's End User License Agreement,
available at:
http://www.cisco.com/c/en/us/td/docs/general/warranty/English/EU1KEN_.html.

Restricted Rights Legend

Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

[*01/01/1970 00:00:24.6125] Made it into bootsh: Aug 3 2017 14:11:36
[*01/01/1970 00:00:24.6125] bootsh build T-b783c0fbb7dde1f5cef7cfb8f1f06c6ba654a78b-gb783c0fb-vipendya
init started: BusyBox v1.23.2 (2017-08-03 13:52:39 PDT)
[*01/01/1970 00:00:27.6415] GCM-128 POST passed
[*01/01/1970 00:00:27.6415] GCM-256 POST passed
[*01/01/1970 00:00:27.9114] Active version: 8.3.122.0
[*01/01/1970 00:00:27.9114] Backup version: 8.2.151.0
[*01/01/1970 00:00:28.1114] AP1852I
Jan 1 00:00:28 FIPS[786]: *** shell: FIPS Mode = disabled ***

User Access Verification
Username: [*01/01/1970 00:00:28.2313] nss_driver - Turbo Support 1
[*01/01/1970 00:00:28.2313] Supported Frequencies - 110Mhz 550Mhz 733Mhz
[*01/01/1970 00:00:28.3513]
[*01/01/1970 00:00:28.3513] phy_value=0: org="0x1000" phy_reg="0x1800"
[*01/01/1970 00:00:28.7412] Current value of FACTORY_RESET=0
[*11/27/2017 23:59:59.0099] Last reload time: Jan 22 13:56:27 2022
[*01/22/2022 13:56:27.0000] Setting system time Sat Jan 22 13:56:27 UTC 2022
[*01/22/2022 13:56:27.0699] device wired0 entered promiscuous mode
[*01/22/2022 13:56:27.1499] device wired1 entered promiscuous mode
[*01/22/2022 13:56:27.1499]
[*01/22/2022 13:56:27.1499] phy_value=0: org="0x1800" phy_reg="0x1800"
[*01/22/2022 13:56:27.5198] stile module dp init successfully
[*01/22/2022 13:56:27.5198] NBAR Label:BLD_MCP_DEV_LATEST_20150424_123021 NBAR VERSION:module build date: Oct 14 2016 at 11:20:56
[*01/22/2022 13:56:28.1097]
[*01/22/2022 13:56:28.1097] boot 2 build T-b783c0fbb7dde1f5cef7cfb8f1f06c6ba654a78b-gb783c0fb-vipendya board corsica mac 74:86:0B:5A:30:A8
[*01/22/2022 13:56:28.1196] Module: mbedtls .text=0xbf000000 data=0xbf007e18 bss=0xbf008070
[*01/22/2022 13:56:28.1196] Module: aptrace .text=0xbf00c000 data=0xbf014044 bss=0xbf014448
[*01/22/2022 13:56:28.1196] Module: qca_nss_gmac .text=0xbf01b000 data=0xbf021b7c bss=0xbf02203c
[*01/22/2022 13:56:28.1196] Module: qca_nss_drv .text=0xbf02b000 data=0xbf042a40 bss=0xbf0437f0
[*01/22/2022 13:56:28.1196] Module: qca_nss_capwapmgr .text=0xbf05f000 data=0xbf062b78 bss=0xbf062cc8
[*01/22/2022 13:56:28.1196] Module: nssmgrctl .text=0xbf068000 data=0xbf069728 bss=0xbf069a4c
[*01/22/2022 13:56:28.1196] Module: proclikefs .text=0xbf06f000 data= bss=0xbf06fb40
[*01/22/2022 13:56:28.1196] Module: stile_lm_ft .text= data= bss=
[*01/22/2022 13:56:28.1196] Module: stile_lm_dp .text= data= bss=
[*01/22/2022 13:56:28.1196] Module: bonding .text=0xbf965000 data=0xbf97663c bss=0xbf976a68
[*01/22/2022 13:56:28.1196] Module: ipv6 .text=0xbf983000 data=0xbf9b3840 bss=0xbf9b50ec
[*01/22/2022 13:56:28.1196] Module: lowmemorykiller .text=0xbf9ce000 data=0xbf9ce2c0 bss=0xbf9ce44c
[*01/22/2022 13:56:28.1196] Module: qca_nss_profile_drv .text=0xbf9d2000 data=0xbf9d3324 bss=0xbf9d3498
[*01/22/2022 13:56:28.5195] Last reload reason : 0: unknown
[*01/22/2022 13:56:30.1590]
[*01/22/2022 13:56:30.1590] __ol_ath_attach() Allocated scn c4000480
[*01/22/2022 13:56:30.1790] Chip id: 0x9, chip version: 0x1000000
[*01/22/2022 13:56:30.1790]
[*01/22/2022 13:56:30.1790] Target Version is 1000000
[*01/22/2022 13:56:30.1790]
[*01/22/2022 13:56:30.1790] Flash Download Address c0000
[*01/22/2022 13:56:30.1790] ol_transfer_bin_file: flash data file defined
[*01/22/2022 13:56:30.1790] Cal location [0]: 00000000
[*01/22/2022 13:56:30.1790]
[*01/22/2022 13:56:30.1790] Wifi0 NAND FLASH Select OFFSET 0x1000
[*01/22/2022 13:56:30.1990] qc98xx_verify_checksum: flash checksum passed: 0x671a
[*01/22/2022 13:56:30.1990] ol_transfer_bin_file 4053: Download Flash data len 12064
[*01/22/2022 13:56:30.2190]
[*01/22/2022 13:56:30.2190] Board data initialized
[*01/22/2022 13:56:30.2590] ol_ath_download_firmware :First OTP download and Execute is good address:0xa000 return param 4660
[*01/22/2022 13:56:30.2590] ol_ath_download_firmware:##Board Id 8 , CHIP Id 1
[*01/22/2022 13:56:30.2590] ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=AR900B/hw.2/boardData_AR900B_CUS260_negative_pwr_offset_2G_v2_008.bin
[*01/22/2022 13:56:30.3390]
[*01/22/2022 13:56:30.3390] [Flash] : Ignore Module param
[*01/22/2022 13:56:30.3490] ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0
[*01/22/2022 13:56:30.3689] ol_transfer_bin_file: Downloading firmware file: AR900B/hw.2/athwlan.bin
[*01/22/2022 13:56:31.4686] Startup Mode-0 set
[*01/22/2022 13:56:31.4686] HTC Service:0x0300 ep:1 TX flow control disabled
[*01/22/2022 13:56:31.4686] HTC Service:0x0100 ep:2 TX flow control disabled
[*01/22/2022 13:56:31.4686] Firmware_Build_Number:5
[*01/22/2022 13:56:31.4686] host/RAM_fw Build Ver Mismatch: H:0x47, F:0x5 !
[*01/22/2022 13:56:31.4686] num_rf_chain:0x00000004 ht_cap_info:0x0000185b vht_cap_info:0x339a79b2 vht_supp_mcs:0x0000ffea
[*01/22/2022 13:56:31.4686]
[*01/22/2022 13:56:31.4686] RES CFG Support wmi_service_bitmap 9778
[*01/22/2022 13:56:31.4686]
[*01/22/2022 13:56:31.4686] Sending Ext resource cfg: HOST PLATFORM as 0 and fw_feature_bitmap as 10 to TGT
[*01/22/2022 13:56:31.4686] Mesh Supported
[*01/22/2022 13:56:31.5486] wmi_ready_event_rx: WMI UNIFIED READY event
[*01/22/2022 13:56:31.5486] ACS not enabled
[*01/22/2022 13:56:31.5586] ol_ath_thermal_mitigation_attach: --
[*01/22/2022 13:56:31.5686] pktlog_init: Initializing Pktlog for AR900B, pktlog_hdr_size = 16
[*01/22/2022 13:56:32.5883] FWLOG: [33776] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 )
[*01/22/2022 13:56:32.5883] FWLOG: [33776] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 )
[*01/22/2022 13:56:32.5883] FWLOG: [33776] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 )
[*01/22/2022 13:56:32.5883] FWLOG: [33776] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 )
[*01/22/2022 13:56:34.6476] wmi_dbg_cfg_send: mod[0]00000000 dbgcfg40000000 cfgvalid[0] 00000000 cfgvalid[1] 00000000
[*01/22/2022 13:56:34.7176] pid 1604's current affinity mask: 3
[*01/22/2022 13:56:34.7176] pid 1604's new affinity mask: 1
[*01/22/2022 13:56:50.8725] Loading sha2...
[*01/22/2022 13:56:50.8725] Dumpping sha1...
[*01/22/2022 13:56:52.6320] Loading MIC cert and key
[*01/22/2022 13:56:52.6320] Dumpping sha2...
[*01/22/2022 13:56:54.4414] Loading MIC cert and key
[*01/22/2022 13:56:54.8013] Generating key, this may take a while...
[*01/22/2022 13:56:56.2708] Public key portion is:
[*01/22/2022 13:56:56.2708] ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQC4Stxvc/1VME4TVysHs9ch2Jq+yzUPL0i3Ha4n2TiwnieUAEPBhwm0qO2g1LZysMIi0anU5ZlCn2k0UtTPQbobBqtsdpd7KJx70fYi27sTxqhhntJw59J16e69Ld00K1/LOH9B3ld7wIvSeENcfUwifDbF0FFx81izWX5J4V5iVduPS8KnL5TKieKb4qi4a1/4CqFzmTMK4sFhDFVgG0fv+3YfPJXXJ3Cql8+3KfpE6Rdn0iakj9a9YgfsYKZ7sH+L3a9WTsGLCkV4zD9/ABFX9aVJuxJedw/LneOFI4a8zSdHrr+c3smnfUuTBfkDJ8CbUjpWPSczJVfgEcSNoxxp root@m74860B5A30A8
[*01/22/2022 13:56:56.2708] Fingerprint: md5 9b:0e:70:89:e6:b5:0e:08:53:73:b4:dc:30:9e:8e:c2
[*01/22/2022 13:56:56.3408] pid 2695's current affinity mask: 3
[*01/22/2022 13:56:56.3408] pid 2695's new affinity mask: 1
[*01/22/2022 13:56:56.8007] gzip -dc /etc/wcp.usermodule.template.gz | sed -e 's/__TX_POWER_2G_FILE__/\/radio_fw\/S2.csv/g' -e 's/__TX_POWER_5G_FILE__/\/radio_fw\/S5.csv/g' -e 's/__EVM_POWER_2G_FILE__/\/radio_fw\/EVM_2.csv/g' -e 's/__EVM_POWER_5G_FILE__/\/radio_fw\/EVM_5.csv/g' -e 's/__DOMAIN_2G__/0/g' -e 's/__DOMAIN_5G__/11/g' -e 's/__PRODUCT_ID__/AIR-AP1832I-A-K9/g' -e 's/__AP_TYPE__/58/g' -e 's/__WIRELESS_MAC__/74:86:0B:5B:1A:00/g' -e 's/__WIRED_MAC__/74:86:0B:5A:30:A8/g' -e 's/__WIRED1_MAC__/74:86:0B:5A:30:A8/g' | DMALLOC_OPTIONS=debug=0x03,inter=1000,log=/tmp/wcp.dmalloc.log,limit=40000000 wcpd &
[*01/22/2022 13:56:57.3105] Password for 'Cisco' changed
[*01/22/2022 13:56:57.6404] WCP: Opening /tmp/var/platform/board_name failed!
[*01/22/2022 13:56:57.6404] WCP: Opening /tmp/var/platform/board_name failed!
[*01/22/2022 13:56:58.3102] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver get_vap_if_index ioctl SIOCGIFINDEX failed for apr1v0 error No such device
[*01/22/2022 13:56:58.3102] wcpd: /san/BUILD/workspace/8.3MR2_Cheetah_Repost_CCO/label/corsica/base/../elts-meraki/elements/wcp/wcp_db.cc: 1351: void WcpDb::populate_if_index_table(): Assertion `if_index >= 0 && if_index < 64' failed.
[*01/22/2022 13:57:10.2465] ethernet_port wired0, ip #IP local net#, netmask 255.255.254.0, gw #IP local net#, mtu 1500, bcast #IP local net#, dns1 #IP local net#, dns2 #IP local net#, domain rsa-arg.com.ar
[*01/22/2022 13:57:32.5995] !!!!! {watchdogd} Process wcpd gone for 60s
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] waiting for WCP to initialize
[*01/22/2022 13:57:57.3718] Socket Invalid Element wcp/wcp_db Handler has_rlan Data 0 Length 10
[*01/22/2022 13:57:57.4117] AP IPv4 Address updated from 0.0.0.0 to #IP local net#
[*01/22/2022 13:57:57.4317] dtls_init: Use MIC device cert
[*01/22/2022 13:57:57.4317] dtls_init: Use MIC device cert private key
[*01/22/2022 13:57:57.4317]
[*01/22/2022 13:57:57.4317] CAPWAP State: Init
[*01/22/2022 13:57:57.4317]
[*01/22/2022 13:57:57.4317] PNP is not required, Starting CAPWAP discovery
[*01/22/2022 13:57:57.4317]
[*01/22/2022 13:57:57.4317]
[*01/22/2022 13:57:57.4317] CAPWAP State: Discovery
[*01/22/2022 13:57:57.4317] Discovery Request sent to #IP WLC#, discovery type STATIC_CONFIG(1)
[*01/22/2022 13:57:57.4617] Discovery Request sent to 255.255.255.255, discovery type UNKNOWN(0)
[*01/22/2022 13:57:57.4617]
[*01/22/2022 13:57:57.4617] CAPWAP State: Discovery
[*01/22/2022 13:57:57.4617] Discovery Response from #IP WLC#
[*01/22/2022 13:57:57.4617]
[*01/22/2022 13:57:57.4617] This AP model is supported by controller version newer than 7.0.0.0!
[*01/22/2022 13:57:57.4617]
[*01/22/2022 13:57:57.4617] Discovery response from MWAR ''running version 0.0.0.0 is rejected.
[*01/22/2022 13:57:57.4617] Failed to decode discovery response.
[*01/22/2022 13:57:57.4617] CAPWAP SM handler: Failed to process message type 2 state 2.
[*01/22/2022 13:57:57.4617] Failed to handle capwap control message from controller - status 4
[*01/22/2022 13:57:57.4617] Failed to process unencrypted capwap packet 0xcad000 from #IP WLC#
[*01/22/2022 13:57:57.4617] Failed to send capwap message 0 to the state machine. Packet already freed.
[*01/22/2022 13:57:57.4617] IPv4 wtpProcessPacketFromSocket returned 4

Re: Access Point not join WLC

Rich R — Fri, 16 Dec 2022 14:10:49 GMT

As others have already pointed out - it's hardware failure - RMA the AP:
[*01/22/2022 13:56:58.3102] DOT11_DRV[1]: wcp/RadDrv1 :: Dot11BaseDriver get_vap_if_index ioctl SIOCGIFINDEX failed for apr1v0 error No such device

Re: Access Point not join WLC

Leo Laohoo — Fri, 16 Dec 2022 14:13:31 GMT

@Nicolasigl wrote:
[*01/22/2022 13:57:57.4617] This AP model is supported by controller version newer than 7.0.0.0!

Upgrade the WLC firmware to 8.X.X.X.

Re: Access Point not join WLC

Rich R — Fri, 16 Dec 2022 14:18:20 GMT

He's on 8.3.122.0 @Leo Laohoo - it's just another failed 1832 and the rubbish/confusing/misleading error messages that COS provides. When the radio fails it still tries to join but the CAPWAP join is malformed (missing information element for the hardware) , which is obviously a bug in and of itself, but the (mis)handling of that is what causes these messages. Of course it doesn't help that they're running such old software ...