topic Re: 802.11ax C9124AXD-E in Wireless

802.11ax C9124AXD-E

mrslyfox686 — Mon, 15 Jan 2024 15:19:44 GMT

Hello

I can’t understand why everything is enabled in the SSID settings for 802.11ax, but in fact on the client side the network is not designated as supporting 802.11ax. Any ideas?

Switch:
Cisco IE-4010-4s24p

PoE injector:
Cisco AIR-PWRINJ6=

AP:
C9124AXD-E
Software Version17.9.4.27
Boot Version1.1.2.4

vWLC:
Cisco Catalyst 9800-CL Wireless Controller
17.9.4a

Running cfg:
802.11ac MU-MIMO : Enabled
802.11ax parameters
802.11ax Operation Status : Enabled
OFDMA Downlink : Enabled
OFDMA Uplink : Enabled
MU-MIMO Downlink : Enabled
MU-MIMO Uplink : Enabled
BSS Target Wake Up Time : Enabled
BSS Target Wake Up Time Broadcast Support : Enabled
802.11 protocols in 2.4ghz band
Protocol : dot11g

Re: 802.11ax C9124AXD-E

balaji.bandi — Mon, 15 Jan 2024 15:44:21 GMT

Depends on your Profile attached to it, you can disable if you do not want.

Re: 802.11ax C9124AXD-E

pieterh — Mon, 15 Jan 2024 16:01:39 GMT

I need to ask to be sure: does this client support 802.11ax ?

your output is only for the vWLC global settings ? (the virtual controller )
-> check the AP / wlan specific configuration

Procedure

Choose Configuration > Tags & Profiles > WLANs.
Click Add. The Add WLAN window is displayed.
Click the Advanced tab.
In the 11ax section, check the Enable 11ax check box to enable 802.11ax operation status on the WLAN.
Click Apply to Device.

Cisco Catalyst 9800 Series Wireless Controller Software Configuration Guide, Cisco IOS XE Cupertino 17.7.x - 802.11ax Per Virtual Access Point [Cisco Catalyst 9800 Series Wireless Controllers] - Cisco

Re: 802.11ax C9124AXD-E

jagan.chowdam — Mon, 15 Jan 2024 16:32:54 GMT

Can you share your WLAN configuration?

802.11ax Config is enabled by default on the WLAN Level.

/** Please rate all useful responses**/

Re: 802.11ax C9124AXD-E

mrslyfox686 — Mon, 15 Jan 2024 21:29:22 GMT

yes, I have several clients equipped with Intel AX210 and AX211 and Samsung Note 20

Re: 802.11ax C9124AXD-E

JPavonM — Tue, 16 Jan 2024 07:02:38 GMT

Can you collect an OTA pcap and confirm whether there are 802.11ax headers on it or not?

If you have not disabled them, these global settings should be there (plus the custom ones per RF-Profile and WLAN-Profile):

wlc# sh run all | i dot11ax
ap dot11 24ghz dot11ax
ap dot11 24ghz dot11ax dynamicfrag
ap dot11 24ghz dot11ax multibssid
ap dot11 24ghz dot11ax spatial-reuse obss-pd
ap dot11 24ghz dot11ax spatial-reuse obss-pd non-srg-max -62
ap dot11 24ghz dot11ax spatial-reuse obss-pd srg srg-max -62
ap dot11 24ghz dot11ax spatial-reuse obss-pd srg srg-min -82
ap dot11 5ghz dot11ax
ap dot11 5ghz dot11ax dynamic-fragment
ap dot11 5ghz dot11ax multiple-bssid
ap dot11 5ghz dot11ax spatial-reuse obss-pd
ap dot11 5ghz dot11ax spatial-reuse obss-pd non-srg-max -62
ap dot11 5ghz dot11ax spatial-reuse obss-pd srg srg-max -62
ap dot11 5ghz dot11ax spatial-reuse obss-pd srg srg-min -82
ap dot11 6ghz dot11ax dynamic-fragment
ap dot11 6ghz dot11ax multiple-bssid
!
//And these are disabled by default
no ap dot11 24ghz dot11ax bss-color
no ap dot11 5ghz dot11ax bss-color
no ap dot11 6ghz dot11ax bss-color

Re: 802.11ax C9124AXD-E

pieterh — Tue, 16 Jan 2024 09:41:08 GMT

be aware this is done separately for 5GHz and for 6GHz band rfprofile

Re: 802.11ax C9124AXD-E

pieterh — Tue, 16 Jan 2024 09:47:03 GMT

I also found this item to configure?
Step 1

Choose Configuration > Radio Configurations > High Throughput.

Step 2

Click the 5 GHz Band tab.

Expand the 11ax section.
Select the Enable 11ax and Multiple Bssid check boxes, if required.
Check either the Select All check box to configure all the data rates or select the desired options from the available data rates list.

Re: 802.11ax C9124AXD-E

mrslyfox686 — Sun, 04 Feb 2024 17:34:58 GMT

Hello @pieterh @JPavonM @balaji.bandi
Unfortunately, I still can't figure out the reason why any of the broadcasted networks are not identified as 802.11ax capable on the client side. Could this be a glitch in the vWLC with this OS version?

Re: 802.11ax C9124AXD-E

Karsten Iwen — Sun, 04 Feb 2024 18:38:24 GMT

You need to show a PCAP of a beacon. This is needed to see what there actually *is* on the WLAN.

Re: 802.11ax C9124AXD-E

mrslyfox686 — Fri, 09 Feb 2024 14:49:33 GMT

Hello @Karsten Iwen @pieterh @JPavonM @balaji.bandi @jagan.chowdam

To ensure that AP begins broadcasting 802.11ax right out of the box, a Factory Reset is required. Essentially, if an AP, currently in operational mode, is reset to factory defaults, upon reconnecting to the same vWLC, it will commence broadcasting 802.11ax.

Why? 😞

Re: 802.11ax C9124AXD-E

pieterh — Fri, 09 Feb 2024 15:26:37 GMT

it will be tagged with all the default-tags, and transmit all the SSID's configured
which suggests that one of your self-defined tags blocks using the "ax" capability

Re: 802.11ax C9124AXD-E

mrslyfox686 — Fri, 09 Feb 2024 16:37:50 GMT

I don’t know, the access point was reset to factory defaults, after which it received the same tag as before. The order was like this:
1. Reset to factory default
2. Executing commands capwap ap primary-base хххххххххххх
capwap ap restart
3. The access point receives the same tag as before the reset and 802.11ax starts working.

Maybe this is due to working in flexconnect mode? or ?