Wirelss controller issue

saquibsalahis — Mon, 05 Jul 2021 18:24:32 GMT

Facing this issue, few APs were not working so rebooted the WLC, after reboot no APs were showing,

set the Controller to factory defaults, configured as per the cisco guide but no hope

present situation:

WLC 4404, APs:LAP1242AG-E-k9

Acess Points are on the old old network :192.168.1.0

(Cisco Controller) >show sysinfo

Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 4.1.171.0
RTOS Version..................................... 4.1.171.0
Bootloader Version............................... 4.1.171.0
Build Type....................................... DATA + WPS

System Name...................................... DISD-WLAN
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.3
IP Address....................................... 192.168.1.199
System Up Time................................... 1 days 23 hrs 21 mins 7 secs

Configured Country............................... GB - United Kingdom
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +50 C

State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
--More-- or (q)uit
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0

Burned-in MAC Address............................ 00:1E:13:2A:E1:80
Crypto Accelerator 1............................. Absent
Crypto Accelerator 2............................. Absent
Power Supply 1................................... Absent
Power Supply 2................................... Present, OK

running config:

(Cisco Controller) >show running-config
802.11a cac voice tspec-inactivity-timeout ignore

802.11a cac voice stream-size 84000 max-streams 2

802.11b cac voice tspec-inactivity-timeout ignore

802.11b cac voice stream-size 84000 max-streams 2

advanced location expiry tags 1200

advanced location expiry client 150

advanced location expiry calibrating-client 30

advanced location expiry rogue-aps 1200

Cisco Public Safety is not allowed to set in this domain

country GB

dhcp create-scope DISD

dhcp address--More-- or (q)uit
-pool DISD 192.168.1.10 192.168.1.150

dhcp enable DISD
dhcp network DISD 192.168.1.0 255.255.255.0
interface address ap-manager 192.168.1.198 255.255.255.0 192.168.1.1

interface address management 192.168.1.199 255.255.255.0 192.168.1.1

interface address service-port 10.1.1.100 255.255.255.0

interface address virtual 1.1.1.1

interface dhcp ap-manager primary 192.168.1.199

interface dhcp management primary 192.168.1.199

interface dhcp service-port disable

interface port ap-manager 2

interface port management 2

logging buffered 1
--More-- or (q)uit

mesh security eap

mgmtuser add admin **** read-write

mobility group domain RFGROUP

msglog level critical

network webmode enable
network telnet enable

network rf-network-name RFGROUP

snmp version v2c enable

snmp version v3 enable

sysname DISD-WLAN

wlan create 1 DISD DISD

wlan security wpa disable 1
--More-- or (q)uit

wlan enable 1

(Cisco Controller) >

(Cisco Controller) >show time

Time............................................. Sat Dec 7 14:39:51 2019

Timezone delta................................... 0:0

NTP Servers
NTP Polling Interval......................... 86400

Index NTP Server
------- --------------------------------

topic Re: Wirelss controller issue in Wireless

Wirelss controller issue

Re: Wirelss controller issue