topic Re: WLC9800 With 10gb port in Wireless

WLC9800 With 10gb port

mohamed-elkaffas — Thu, 16 Jan 2025 23:09:26 GMT

i installed wlc9800 17.16.01 on esxi8 , with dedicated port 10gb

Cisco core switch read it 10gb

Esxi read it 10gb

cisco wlc 9800 read it 1gb

is that normal with WLC 9800 or i miss something ?

WLC#show interfaces gigabitEthernet 1 GigabitEthernet1 is up, line protocol is up Hardware is vNIC, address is 0050.56bf.d3c3 (bia 0050.56bf.d3c3) MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full Duplex, 1000Mbps, link type is auto, media type is Virtual output flow-control is unsupported, input flow-control is unsupported ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:05, output 00:00:03, output hang never Last clearing of "show interface" counters never Input queue: 0/375/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 13000 bits/sec, 16 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 8532 packets input, 893763 bytes, 0 no buffer Received 0 broadcasts (0 multicasts) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 47 packets output, 11055 bytes, 0 underruns Output 0 broadcasts (0 multicasts) 0 output errors, 0 collisions, 0 interface resets 1 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 pause output 0 output buffer failures, 0 output buffers swapped out

Re: WLC9800 With 10gb port

Flavio Miranda — Thu, 16 Jan 2025 23:16:45 GMT

@mohamed-elkaffas

As the interface is GigabitEthernet, the information you see is correct.

WLC#show interfaces gigabitEthernet 1
GigabitEthernet1 is up, line protocol is up
  Hardware is vNIC, address is 0050.56bf.d3c3 (bia 0050.56bf.d3c3)
  MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,

In order to achieve 10Giga the interface should be TenGigabitEthernet

Re: WLC9800 With 10gb port

mohamed-elkaffas — Thu, 16 Jan 2025 23:17:48 GMT

how to make it TenGigabitEthernet and the installation read it 1gb

Re: WLC9800 With 10gb port

Flavio Miranda — Thu, 16 Jan 2025 23:22:13 GMT

Which WLC size did you instaled?

Re: WLC9800 With 10gb port

mohamed-elkaffas — Thu, 16 Jan 2025 23:23:13 GMT

large , private cloud

Re: WLC9800 With 10gb port

Flavio Miranda — Thu, 16 Jan 2025 23:31:15 GMT

Actually it does not matter. The interfaces will be giga anyway. If you need more than 1 Giga, you can work with port-channel.

But the overall throughput is much less the 10 Giga.

Supports up to 2.1 Gbps of throughput in a centralized wireless deployment (low-throughput profile without SR-IOV)

With a high (enhanced) throughput profile, up to 5 Gbps can be reached on ESXi and KVM with the right set of network cards

Re: WLC9800 With 10gb port

mohamed-elkaffas — Thu, 16 Jan 2025 23:35:29 GMT

thanks alot for your help , but i have another question does wlc9800 support port channel or from coreswitch side !

Re: WLC9800 With 10gb port

Flavio Miranda — Thu, 16 Jan 2025 23:48:15 GMT

Now you got me. Thinking better I dont believe you can configure the WLC with port-channel. You can use trunk but not port-channel.

On this guide we can see that only one interface is given as option for Management

https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/9800-cloud/installation/b-c9800-cl-install-guide/booting_the_controller_and_accessing_the_console.html

On the following guide they show the configuration for ESXI. See the section "Configuring NIC Teaming on a Virtual Switch"

https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/9800-cloud/installation/b-c9800-cl-install-guide/installing_the_controller.html#task_es3_zfz_bdb

Re: WLC9800 With 10gb port

Rich R — Sat, 18 Jan 2025 15:01:31 GMT

On 9800-CL the name GigabitEthernetX is irrelevant because it's a virtual interface to a virtual switch and there is no direct relationship with the physical interface on the server.
"show int" shows "Hardware is vNIC" and "media type is Virtual" and although it shows "1000Mbps" that has no impact of the rate of traffic through the interface.

> is that normal with WLC 9800 or i miss something ?
That is normal for 9800-CL. You missed the fact that the 9800-CL is not directly connected to the 10G interface as a physical 9800-80 appliance would be.