topic Re: Profile 5ghz only in Wireless

Profile 5ghz only

Pedro10 — Tue, 02 Oct 2018 16:47:41 GMT

Hello everyone,

I have 11 MR33 with 2 SSID's. I would like to disable the 2.4ghz radio from only 1 of these 11 AP's.

What is the most correct way to do this? Create an RF profile for it? Is it really possible to unhit the 2.4ghz radio?

Thank you,
Pedro.

Re: Profile 5ghz only

Pedro10 — Tue, 02 Oct 2018 17:11:50 GMT

I activated a new RF profile only for 5ghz in 1 AP only. Looks like it worked.

I just wanted to know even if this was the right concept.

Thank you.

Re: Profile 5ghz only

hody.crouch — Tue, 02 Oct 2018 17:14:01 GMT

Yes, you would create two RF Profiles. You then assign the RF profiles to your access points using the Wireless > Radio Settings page.

You will find settings for 5GHz-only, 2.4GHz-only, and dual-band (with optional steering) on the RF Profile page.

Re: Profile 5ghz only

paul.groves.rdc — Wed, 17 Apr 2019 07:31:14 GMT

Hi, I was wondering if your 2.4GHz actually turned off. We have MR53E APs and applying a 5GHz only profile didn't turn off the 2.4GHz radio.

I found that there are no SSIDs being broadcast on the 2.4GHz but the 2.4GHz isn't turned off. If I attempt to set the target power for 2.4GHz on an AP to Off, it goes to full power 29 dBm.

We are using firmware 26.2 as that was recommended by Meraki.

Re: Profile 5ghz only

Pedro10 — Wed, 17 Apr 2019 11:41:34 GMT

@paul.groves.rdc

How are you

In fact what is recommended are RF Profiles.
There you create a new profile and you can leave channel 5 or 2.4ghz enabled or disabled, for example.

After creating this profile you inform which access point you will place.

For now it's this solution I found.

Good luck
Peter.

Re: Profile 5ghz only

egmachate — Wed, 08 May 2019 12:52:28 GMT

What are your thoughts on running 5ghz only in all MRs?

Re: Profile 5ghz only

joey.debra — Wed, 08 May 2019 18:58:07 GMT

If all critical devices in your org support 5GHz and your coverage meets the requirement on 5GHz, then go for it!

Re: Profile 5ghz only

paul.groves.rdc — Wed, 08 May 2019 20:29:03 GMT

@egmachate wrote:
What are your thoughts on running 5ghz only in all MRs?

Hi, not an option. It's an events venue so will still have older 2.4GHz devices.

Re: Profile 5ghz only

Dalmiro.Couto — Mon, 24 Jun 2019 19:15:40 GMT

I have the same question. While SSID broadcast is disabled on 2.4 GHZ, the radio is still on and I can't find a way to completely disable 2.4ghz band.

Re: Profile 5ghz only

RSU21it — Mon, 24 Jun 2019 23:28:08 GMT

@Dalmiro.Couto - If I recall correctly, selecting Disable on the 2.4 radio does disable it for any client usage but the AP will still use that band for AP to AP meshing traffic even if the AP is in Gateway mode.

Perhaps Meraki or someone else in the community can confirm this. Don't want to start any rumors...

Re: Profile 5ghz only

Dalmiro.Couto — Tue, 25 Jun 2019 12:35:26 GMT

Yeah, I agree. I would love a future option to completely disable 2.4 GHz radio propagation (even scanning). It's a waste of power in my case.

Re: Profile 5ghz only

Nolan H. — Tue, 25 Jun 2019 14:54:11 GMT

It would be nice if it would actually power off, however I do not think that is something that is possible.

Closest I know to getting to actually 'OFF' is to either set the radio to OFF under the power settings manually (or doing it through the RF Profile method which always seems difficult for some reason), and then contacting Meraki support to have them give you the toggle option under General settings, to disable MESHING.

You shouldn't 'see' any wireless frames then going across the air, however I believe you'll still see the AutoRF changing channels. You can ignore the TX power setting the 2.4GHz radio 'grabs' because its never the same for me. One AP might show 29dBm, another might show 6dBm, both set to OFF. I just ignore it and move on.