topic Hello!Code is 7.6.100.0The in Wireless

WLC 2504: https access to dynamic interface over L3

Jaaazman777 — Mon, 05 Jul 2021 07:56:53 GMT

Hello!

I have a problem with acccessing WLC 2504 dynamic interface with GUI https connection, when I am trying to acccess it from another L3 network.

physic and logic shemes are attached.

the command config network mgmt-via-dynamic-interface enable was already executed at the WLC.

Assume that WLC dynamic interface has ip 192.168.1.10/24 with gw 192.168.1.1 (SW1)

https, ICMP and ssh connection from PC2 (192.168.1.2) to 192.168.1.10 is ok , but from PC1 (192.168.2.2) to 192.168.1.10 only ICMP works and no https and ssh connection.

As far as ICMP works, routing is ok, there is also no firewall between WLC and 192.168.2.0/24 network.

The SW1 has no ACL on its SVI interfaces.

What can cause such kind of problem?

Thank you in advance!

Hi,Any ACLs on WLC?

Christos Stefaneskou — Thu, 05 Jun 2014 18:38:48 GMT

Hi,

Any ACLs on WLC?

Hello!no ACL on the WLC here

Jaaazman777 — Fri, 06 Jun 2014 05:56:20 GMT

Hello!

no ACL on the WLC

here is the config of mgmt2 interface

show interface detailed mgmt2

Interface Name................................... mgmt2
MAC Address...................................... b8:38:61:XX:XX:XX
IP Address....................................... 192.168.1.10
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.1.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
Quarantine-vlan.................................. 0
NAS-Identifier................................... wlc1
Active Physical Port............................. 3
Primary Physical Port............................ 3
Backup Physical Port............................. Unconfigured
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 192.168.1.1
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
IPv4 ACL......................................... Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... No
Guest Interface.................................. No
L2 Multicast..................................... Enabled

What code ? Did you reboot by

George Stefanick — Sat, 07 Jun 2014 20:54:36 GMT

What code ? Did you reboot by chance ? Shouldnt be required to but you know how it goes ..

If you are trying to open WLC

Vinod Arya — Sun, 08 Jun 2014 15:46:20 GMT

If you are trying to open WLC from a client who is connected to an AP managed by same WLC's, you may have to enable the Mgmt Via Wireless option to open the Management Via Wireless page from client.

You can enable it via CLI from the following command :

config network mgmt-via-wireless enable

OR do it from GUI from :

Step 1 Choose Management > Mgmt Via Wireless to open the Management Via Wireless page.

Step 2 Select the Enable Controller Management to be accessible from Wireless Clients check box to enable management over wireless for the WLAN or unselect it to disable this feature. The default value is unselected.

Step 3 Click Apply to commit your changes.

Step 4 Click Save Configuration to save your changes.

-Thanks

Vinod

**Encourage Contributors. RATE Them.**

Hello!I'm trying to access

Jaaazman777 — Mon, 09 Jun 2014 06:52:12 GMT

Hello!

I'm trying to access WLC from the wired network.

Hello!Code is 7.6.100.0The

Jaaazman777 — Mon, 09 Jun 2014 10:33:42 GMT

Hello!

Code is 7.6.100.0

The reboot didn't help