topic Re: WLC 5508 deployment question in Wireless

WLC 5508 deployment question

egua5261 — Sun, 04 Jul 2021 05:27:17 GMT

Hi There,

Planning to migrate existing WAPs (which models are supported in LW mode and by the controller, already checked), currently running in Autonomous mode.

My question is what will happen when I bring the WLC online in the same LAN as these existing WAPs, will they be affected in anyway, if as I said they are running in autonomous mode, i dont think so, but just double checking just in case?

The plan is to migrate them over without any down time.

Cheers,

egua5261

Re: WLC 5508 deployment question

Scott Fella — Wed, 25 Jul 2012 01:38:20 GMT

It is fine if the WLC is placed in the same subnet as the current access points.

Sent from Cisco Technical Support iPad App

Re: WLC 5508 deployment question

Scott Fella — Wed, 25 Jul 2012 01:41:16 GMT

Just to add, the suggestion is no more than 60 access points in the same subnet as the WLC. This is a suggestion though as I have seen larger number with no issues. Also your current access point are connected to a switch with a trunk port? If the access point will be converted and configured in local mode, the port should be changed to an access port.

Sent from Cisco Technical Support iPad App

WLC 5508 deployment question

egua5261 — Wed, 25 Jul 2012 03:57:32 GMT

Hi Scott,

Thanks for your prompt response.

Indeed the existing WAPs are connected to switchports in trunk mode, as the need to run multiple VLAN ids on the WAPs. So when migrated, are you saying there wont be a need to configure multiple VLANs on the access points but in the WLC controller only?

Cheers,

egua5261

Re: WLC 5508 deployment question

Scott Fella — Wed, 25 Jul 2012 04:01:43 GMT

When an ap is in local mode, all traffic is tunneled back to the wlc. So the wlc will be connected to a trunk port only allowing whatever vlans have been defined on the wlc.

Sent from Cisco Technical Support iPhone App

WLC 5508 deployment question

egua5261 — Wed, 25 Jul 2012 04:38:04 GMT

What is local mode? is that equivalent to Light Weight mode?

Re: WLC 5508 deployment question

Scott Fella — Wed, 25 Jul 2012 11:35:50 GMT

Local mode is the default mode on most Cisco lightweight access points. The other used mode is h-reap which is now called FlexConnect.

Sent from Cisco Technical Support iPhone App

Re: WLC 5508 deployment question

egua5261 — Wed, 01 Aug 2012 07:51:08 GMT

Hi Scott,

I've enabled connectivity between the controller and the neighboring switch (catalyst 4500 series) using etherchannel. Since I decided to enable LAG in the controller. I have assigned an IP to the management interface and a VLAN ID (15) since I decided to use a tagged VLAN for it.

What I'm getting is the switchport interface in the catalyst switch in a suspended state. Not too sure why? see the config below,

sh int gi7/46

GigabitEthernet7/46 is up, line protocol is down (suspended)

switch1#sh int gi7/46 status

Port Name Status Vlan Duplex Speed Type
Gi7/46 suspended 1 a-full a-1000 10/100/1000-TX

I created a port-channel interface and only one interface is currently bound and only one port is being used in the controller.

interface Port-channel7

switchport

switchport trunk encapsulation dot1q

switchport trunk allowed vlan 10-20

switchport mode trunk

end

interface GigabitEthernet7/46

channel-group 7 mode on

I have made sure the speed and duplex setting are the same in the controller's port and the switch port.

(Cisco Controller) >show port summary

           STP   Admin   Physical   Physical   Link   Link
Pr Type   Stat   Mode     Mode      Status   Status Trap     POE    SFPType
-- ------- ---- ------- ---------- ---------- ------ ------- ------- ----------
1 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
Hope you can point me in the right direction here,

Cheers,

egua5261

Re: WLC 5508 deployment question

grabonlee — Wed, 01 Aug 2012 08:11:49 GMT

Please could you do the following:

1. Do a shut and not shut. If the etherchannel does not come, go to step 2

2. Manually set the speed and duplex of the gigabit interface to 1000 and full.

3. After setting the speed and duplex, do a SH and no SH.

Re: WLC 5508 deployment question

egua5261 — Thu, 02 Aug 2012 00:17:39 GMT

Hi Osita,

I followed the steps you provided but it did not bring the interface UP.

It came up once I added the trunking configuration to the interface itself,

int gi7/46

switchport trunk encapsulation dot1q

switchport mode trunk

I was under the impression, etherchannel would do it automatically, as long as the config was added to the port-channel interface. But it did not happen in this switch.

Thanks,

egua5261.

Re: WLC 5508 deployment question

grabonlee — Thu, 02 Aug 2012 08:24:28 GMT

Nice to know that the problem is solved. Always remember that the switch port is configured first and properly b4 setting up etherchannel. The etheris dependent on the switchport.

Cheers