topic Everything is working in Wireless

3650 and AIR-CAP3702I-E-K9 - AP only join in access port

albertofdez — Mon, 05 Jul 2021 10:53:25 GMT

Hi,

I have a stack consisting of 2 WS-C3650-24PS (version 03.03 .05SE) configured as MC and 4 AIR-CAP3702I-E-K9.

Everything is working properly and the APs are joined without problems, but only if the port of the 3650 is configured in access mode. This is a problem because i need to set up multiple SSIDs in different VLANs and i need that the AP can join in a trunk port mode.

This scenario what i have set up in other occasions WLC in 2504 and 5508 without any problem.

How do I configure multiple SSIDs in different VLANs but can I put the port mode in trunk?

Best regards.

Everything is working

Rasika Nayanajith — Wed, 09 Sep 2015 00:30:21 GMT

Everything is working properly and the APs are joined without problems, but only if the port of the 3650 is configured in access mode.

This is a prerequisite for Converged access wireless where you have to connect AP directly onto switch (MA) where port is configured as a "Access Port".

You cannot connect AP on trunk port (as it is unsupported). But this will not limited to configure multiple SSID on different vlans in Converged access. Since CAPWAP establish between AP and 3650 switch, you do not want dot1q trunk between AP and Switch.

HTH

Rasika

*** Pls rate all useful responses ***

Hi Rasika,If the port is

albertofdez — Wed, 09 Sep 2015 07:01:57 GMT

Hi Rasika,

If the port is configured in access mode, how the aps put the traffic in the correct vlan?

There are any configuration special in the port or in the wlan?

Best regards.

Hi ,WLC and AP establish

Sandeep Choudhary — Wed, 09 Sep 2015 12:14:27 GMT

Hi ,

WLC and AP establish CAPWAP tunnel and all traffic flow in it.

here is the link which tells u more about LWAPP/CAPWAP traffic study..

http://www.cisco.com/en/US/tech/tk722/tk809/technologies_white_paper09186a0080901caa.shtml

Regards

Don't forget to rate helpful posts

Hi Rasika,And the AP has to

albertofdez — Mon, 14 Sep 2015 10:33:00 GMT

Hi Rasika,

And the AP has to be necessarily connected to a 3650 MC mode in 3650 in MA or another way, is it right?

There is an official document discuss this restriction?

Best regards.

can albertofdez guide me

yoga_1980 — Sun, 27 Sep 2015 11:18:49 GMT

can albertofdez guide me to configure the AIR-CAP3702I-E-K9 , plz when I login I can't get global config mode. plz help me

Use this command : debug

Sandeep Choudhary — Sun, 27 Sep 2015 12:25:23 GMT

Use this command : debug capwap console cli

Regards

dont forget to rate helpful post

Hi,You will be using a

albertofdez — Sun, 27 Sep 2015 12:41:27 GMT

Hi,

You will be using a lightweight version and therefore can not enter setup mode. Use these commands

ap#debug capwap console cli

ap#configure terminal

I am not able to go console

yoga_1980 — Mon, 28 Sep 2015 06:37:37 GMT

I am not able to go console cli

ap# debug capwap ?

client

mcast

mfp

these only I can see

Just give this command

Sandeep Choudhary — Mon, 28 Sep 2015 07:48:11 GMT

Just give this command altogether:

debug capwap console cli

regrads